• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Motor Mount

BubMullen

Contributor
Jr. Member
Joined
Oct 20, 2025
Messages
63
I believe I have a motor mount issue. Truck idles fine in park and neutral but in drive it shakes pretty bad, and also when taking off the line there is a pause then a high rev take off.

So if that is the problem, how hard to swap motor mounts on a 302 ?

is this something I can do with a hydraulic jack, a block of wood and sockets set?

Do I have to unbolt/remove other stuff or just focus on the motor mounts?
 

jeffncs

Contributor
Bronco Guru
Joined
May 4, 2004
Messages
1,898
Loc.
Raleigh, NC
The motor mounts are pretty easy to replace - it’s 2 bolts annd a nut and an engine hoist or a floor jack to lift the engine to swap the mount.

Typically, a bad/broken motor mount presents as the engine shifting under acceleration and clunking / banging. It’s not usually a “vibration”.

Can you describe the vibration? Is the engine sputtering or changing behavior? What happens with the engine when you first touch the gas pedal? Does the vibration go away when driving? Any vibration when in P or N?
 
OP
OP
B

BubMullen

Contributor
Jr. Member
Joined
Oct 20, 2025
Messages
63
The vibration just shakes the vehicle pretty bad. If I shift to neutral it stops. No vibration in park either When I first touch gas it takes a couple of seconds to respond then takes off
 

Broncobowsher

Contributor
Total hack
Joined
Jun 4, 2002
Messages
37,111
I'm going to say that it's not a motor mount. Sounds more of a tune up issue. Misfire under load, possible ignition. Delayed throttle response, possible carb issue.
 

SLOWnEASY

Contributor
Sr. Member
Joined
Sep 26, 2022
Messages
526
Loc.
San Diego, Ca.
when taking off the line there is a pause then a high rev take off.

When I first touch gas it takes a couple of seconds to respond then takes off
From your other post you have a 1973 with a 302 and a C4. The above are from post #1 and post #3. Is post 3 the same concern as post #1 but just reworded for clarity? Or
are you talking about two different things? Like are you saying you hit the gas and there is a pause and then the engine speed increases and then there is an additional pause before the truck takes off? I'm assuming it's just a rewording but figures it's best to ask.
 
OP
OP
B

BubMullen

Contributor
Jr. Member
Joined
Oct 20, 2025
Messages
63
Well that is a heck of a lot better than motor mount

Sounds like a tuneup next weekend
 

Broncobowsher

Contributor
Total hack
Joined
Jun 4, 2002
Messages
37,111
Plugs, wires, cap, rotor, carb issue, vacuum leak. Any of those are on the suspect list. And that is not an all inclusive list either, there are still other things. Fixing the problem is generally the easy part, diagnosing the problem is where the struggle is usually at.
 
OP
OP
B

BubMullen

Contributor
Jr. Member
Joined
Oct 20, 2025
Messages
63
sounds like the diagnosis is the hard part I hope I can check a couple of things tonight
 

EPB72

Contributor
Bronco Guru
Joined
Jul 13, 2019
Messages
1,216
Loc.
Pleasant Hill, CA
From your other post you have a 1973 with a 302 and a C4. The above are from post #1 and post #3. Is post 3 the same concern as post #1 but just reworded for clarity? Or
are you talking about two different things? Like are you saying you hit the gas and there is a pause and then the engine speed increases and then there is an additional pause before the truck takes off? I'm assuming it's just a rewording but figures it's best to ask.
Have you checked your ATF level /conditio? Could be a reason for engine rev before moving.

If you power brake can you induce/ intensify vibration ,, a lot of things could be cause of vibration,

Running condition well checking basics ,, ignition ,, preform power balance,, carb/ / exterminator if you have a lean condition . Vacuum leak ,,

Motor mount unlikely BUT I ‘ve seen to many unlikelys ,,, a sagged mount is usually the culprit where there’s metal to metal contact ,, trans mounts would do quick visual ,,
Usually determining a drivetrain type vibration or engine running condition is fairly obvious but hard to say without being ther ,, good luck
 
OP
OP
B

BubMullen

Contributor
Jr. Member
Joined
Oct 20, 2025
Messages
63
Thanks for all the info

Yes I thought I had it narrowed to the motor mount so I asked a different way. Sorry about that

Last night I checked the hose and PCV. The hose was loose so I put a hose clamp on and snugged it down. That didn’t help. Question about PCV it is extremely loose in the oil filler cap is that expected? Should I be able to lift straight out?

I did the check of putting one foot on brake, place in drive and give it just a little gas. That did end the vibration. Can you help me understand why that would be? Is idle too low?

Thanks again guys. I am learning and couldn’t do this without you all
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
Question about PCV it is extremely loose in the oil filler cap is that expected? Should I be able to lift straight out?
Yes, it should come straight out with a light pull.
The better it seals, the better off you are overall. So if it’s really loose and floppy, maybe a new grommet is called for.
But other than that, it’s just a very light restriction fit.
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
I did the check of putting one foot on brake, place in drive and give it just a little gas. That did end the vibration. Can you help me understand why that would be? Is idle too low?
Yes, but unfortunately, it could still be many things. Lots of reasons for it to change a vibration or the way it runs by adding a little load. Or even just RPM.

Have you tried removing any fan belts to see if it’s one of the accessories?

When you put your foot on the break and push the gas pedal, did the engine twist in the mounts?
It’s theoretically possible for an engine mount to be bad inside and transmit more of the engine vibration to the frame, but I’ve never seen or heard of that happening.

Good Nathan follow the entirety of the exhaust system. See if there is anywhere that’s even remotely close to another piece of metal. Such as body or frame.

Pull the boot off the transfer case shifter, or any other shifter that comes to the floor, and see if anything is remotely close to touching the body.

Could be as simple as a vacuum leak. Without rereading, did you check for vacuum leaks, using some sort of a precision spray around the engine?
Got pictures of your overall engine compartment for us to see?
 
OP
OP
B

BubMullen

Contributor
Jr. Member
Joined
Oct 20, 2025
Messages
63
I did not check for a vacuum leak last night, if I can get to it I will do that this evening
 
Top