• Just a reminder that you won't be able to start new posts or reply to existings posts in the Archive forum.

    This is where all the old posts go so they can still be used for reference and searched.
  • Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Moving driver side seat back

daddycreswell

Contributor
Bronco Guru
Joined
Jul 30, 2011
Messages
2,854
Loc.
Lebanon, TN
While I have the driver side seat out to recover, I was looking at maybe moving it back a couple of inches to give my 6' 3' frame some more room. Is it as simple as measuring back a couple of inches and drilling new holes? The holes toward the door would be easy to access from under the tub, but the ones toward the middle look like they are covered underneath. Any suggestions?
 

asinor

Bronco Guru
Joined
May 13, 2011
Messages
1,396
Loc.
Tulsa, OK
Use some kind of reinforcement under the floor pans (fender washers or something). I know the passenger side mounts go through a body brace, not sure about the driver side.
 

NGABronco

Contributor
Always Learning
Joined
Feb 4, 2007
Messages
7,574
Loc.
N. GA now South Carolina
Make a 1"x4" plate that will bolt into the original hole, weld a stud onto the other end and use a nut to hold the seat down, I've done that on several rigs, (I'm 6'5") and it's easy to go back to stock.!!%)%)%)
 
OP
OP
daddycreswell

daddycreswell

Contributor
Bronco Guru
Joined
Jul 30, 2011
Messages
2,854
Loc.
Lebanon, TN
Make a 1"x4" plate that will bolt into the original hole, weld a stud onto the other end and use a nut to hold the seat down, I've done that on several rigs, (I'm 6'5") and it's easy to go back to stock.!!%)%)%)

Thanks NGA, I will try that.
 

snipi

Full Member
Joined
Feb 15, 2011
Messages
166
Loc.
Mesa
if you drill you might want to drop the auxillary tank mine was already out when i did mine, I really like the idea already posted above
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
I like NGA's method too, but did mine slightly differently.
I drilled the holes in the floor where I wanted them, then backed them up with some nuts welded to 1/4" thick plate steel as a reinforcement plate.

Instead of the stud (which might be easier and a better idea anyway) I simply drilled and tapped the plate, welded the nut in place, then welded the plate to the underside of the floor.

Seems to be sufficiently strong to my way of thinking.

Paul
 

Yeller

Contributor
Bronco Guru
Joined
Mar 27, 2012
Messages
7,692
Loc.
Rogers County Oklahoma
I lowered the seat 4" and pushed it back, I'm 6' and feel like a kid. It sure is nice looking through the center of the windshield and not at the top of the frame.
 
OP
OP
daddycreswell

daddycreswell

Contributor
Bronco Guru
Joined
Jul 30, 2011
Messages
2,854
Loc.
Lebanon, TN
I lowered the seat 4" and pushed it back, I'm 6' and feel like a kid. It sure is nice looking through the center of the windshield and not at the top of the frame.

How did you lower the seat? Did you cut the cut the step up out
 

Yeller

Contributor
Bronco Guru
Joined
Mar 27, 2012
Messages
7,692
Loc.
Rogers County Oklahoma
I cut floor flat all the way back to the bed floor on both sides and set the seats to match. Everything was crusty anyway and needed replacing.

Its kind of fun to pull up next to a stock unlifted truck and look eye to eye with them when your sitting on 37's. No lift with 37's, they fit nice with modified rear wheel houses and no inner fenders
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
I hope you took lots of progress pics of that project Yeller!
Any chance you have a build thread with regard to the seat lowering? Be nice to see.
There are quite a few that would like to lower their seats, and even one who's going to be doing that for a customer's Bronco.

Be nice to see how it turned out at least.

Paul
 

Yeller

Contributor
Bronco Guru
Joined
Mar 27, 2012
Messages
7,692
Loc.
Rogers County Oklahoma
I'm horrible about taking pics, I took a few of the build but no thread. I do have a few that I could email that show it somewhat, PM me your addy.

There's really not much bronco left except the body, I built my own chassis and used parts that I had from other projects, most of them from the evil bow tie. Some say what I've done is sacrilige but I did pull it off the trailer headed to the scrap yard, so I say its another getting the love it deserves instead of being gone forever.
 

andyp

Contributor
Sr. Member
Joined
Jan 28, 2011
Messages
898
Make a 1"x4" plate that will bolt into the original hole, weld a stud onto the other end and use a nut to hold the seat down, I've done that on several rigs, (I'm 6'5") and it's easy to go back to stock.!!%)%)%)

Any pics?
 
Top