• Just a reminder that you won't be able to start new posts or reply to existings posts in the Archive forum.

    This is where all the old posts go so they can still be used for reference and searched.
  • Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

My Rock Slider / Ski Build

Bundy

Bronco Guru
Joined
Jan 10, 2009
Messages
2,045
After browsing around for ages on here I finally pulled the trigger and jumped into getting rid of my rusted out rockers and replacing them with 2x6 3/16" rectangular tube to provide ultimate protection out on the trail.

I started by measuring down from the sill about 3/4", taped a line and started cutting with an angle grinder with a cut off disc for the outer line and had to use the ole sawzall for some of the inner where it connected to the door post.

As you can see, both the inner and outer rocker were pretty much destroyed so I opted to weld supports to the frame instead of welding them to the inner rocker.
 

Attachments

  • Marked4cut.jpg
    Marked4cut.jpg
    198.9 KB · Views: 304
  • PassDoorPsot.jpg
    PassDoorPsot.jpg
    88 KB · Views: 285
  • folded rust.jpg
    folded rust.jpg
    213.6 KB · Views: 287
  • old rocker.jpg
    old rocker.jpg
    97 KB · Views: 266
  • rocker cut.jpg
    rocker cut.jpg
    88.5 KB · Views: 332
OP
OP
Bundy

Bundy

Bronco Guru
Joined
Jan 10, 2009
Messages
2,045
I decided to go with the 2x6 instead of the 2x5 so that it would protrude a bit more to act as more of a step and also make contact with rocks way before the rest of the body would.

I left a small lip of the inner rocker to act as a guide so the ski would be (mostly) even along the rocker. Once the tube was clamped in place I was able to measure both ends and opted to cut about an inch from the edge of the fenders just in case I want to ever jump up to 37" tires in the future.

After the length of the skis were determined I wanted to cut the ends at 45 degrees and cap them but my chop saw was too small to take 2x6 rectangle (but I'm sure 2x5 would have fit %)) so I reverted back to the angle grinder/cutoff wheel and a 99 cent protractor. To my surprise they came out really well freehand cutting the angles and only needed minimal grinding for the caps to seat nicely.
 

Attachments

  • clamped.jpg
    clamped.jpg
    80.4 KB · Views: 301

tasker

Contributor
all knowing of nothing
Joined
Jun 2, 2006
Messages
21,707
Loc.
NH
LOOK AWESOME, exactly what i'd like to do to mine at some point.
 
OP
OP
Bundy

Bundy

Bronco Guru
Joined
Jan 10, 2009
Messages
2,045
My next move was to measure from the tube to the frame for the 2x2 supports that were being welded to the frame.

I opted to weld 3/16" plates to frame and didn't really have to cut the supports any shorter to allow for the extra plate as it wasn't a major concern exactly how far they stuck out just as long as it was a uniform distance.

After I had the 2x2 supports cut I tacked them to the sleds and clamped it back up to figure out where to put the plates I wanted to weld to the frame... but before I welded the plate to the frame I had to remove the damned rhino lining from the surface.

Stupidly I spent an $8 flapping wheel before I realized the flapper just melts the lining and ruins the disc so I switched over to a paint stripping disc and alot of stripping later I was able to tack in the plates. The plates near the rear spring hangar had to be raised pretty high up since the frame moves slightly up but I was able to weld 3 sides and not the top which I wouldn't have been able to weld anyway with the tub in the way.
 

Attachments

  • Frame2.jpg
    Frame2.jpg
    102.1 KB · Views: 307
  • Frame.jpg
    Frame.jpg
    111.9 KB · Views: 287
  • Welded sku.jpg
    Welded sku.jpg
    103.7 KB · Views: 277
OP
OP
Bundy

Bundy

Bronco Guru
Joined
Jan 10, 2009
Messages
2,045
another thing I had to consider when placing the 2x2 supports was the potential upgrade for extended arms and where the new bracket would be. Since most vendors sell kits that are moved back 11" or less, I was able to measure and place the suppors far enough back to leave the space open for future brackets.

After all the fitting I was able to finish welding the plates to the frame and the supports to the sleds.

Then it was primer and paint. I used a can of rustoleum on the door support and old rocker area (after a good wash and scrub) to try to prevent further rust.

After that I just clamped the sleds back into place with the 2x2 supports attached and was able to weld the support to the frame plates!
 

Attachments

  • paint.jpg
    paint.jpg
    110.6 KB · Views: 239
  • Finished.jpg
    Finished.jpg
    80.5 KB · Views: 330
OP
OP
Bundy

Bundy

Bronco Guru
Joined
Jan 10, 2009
Messages
2,045
Thanks guys- I'm pretty pumped on them!

The only problem is that since I have more protection my driving style has gotten quite a bit more aggressive ;D

Oh and my first major scratch on them hahaha

Here is a crappy little vid which you can seem em a little better in action
http://www.youtube.com/watch?v=2Mh8Ob1SqMo
 

Attachments

  • first ding.jpg
    first ding.jpg
    55.8 KB · Views: 250

NateMob

Full Member
Joined
Jul 24, 2011
Messages
248
I need someone close to me to build me some of these. Yours look great.
 
OP
OP
Bundy

Bundy

Bronco Guru
Joined
Jan 10, 2009
Messages
2,045
Thank you- they were super easy to do... most of the time was all prep; cutting, grinding, beveling, flapping, stripping (the paint). I planned on about 10 hours and it took me 24 but that's pretty typical ;D
 

Oatmeal

Sr. Member
Joined
May 17, 2009
Messages
664
I've been wanting to do this to mine for a really long time but, I would really miss my aux tank.
Then, I realized something, I AM a sheetmetal guy for f..k's sake and I could build a smaller tank to fit there, it won't hold as much but....I'm just really lazy%) however, when I get motivated, I know I'll really get into it.
Hmm.....I should probably build a rear tank too ?:?

I once built a set of rocker guards (just like Chuck's Rock Skis.....before he was selling his) out of 7 gauge stainless steel for a buddy's Bronco (they are hell for tough, by the way) but, it was so much work that, I didn't even make a set for mine.....lazy%)

Hans
 
Top