• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Original C bushings

jckkys

Contributor
Bronco Guru
Joined
Mar 15, 2012
Messages
5,221
The poly C bushings I have are marked front and rear. The OE rubber bushings don't seem to be. In fact they have the same Ford part number. I always heard the stock suspension C bushings were 2 degree. So if that's true there must be something about the OE bushings that give them what the 2 degree poly bushings do.
 

Broncobowsher

Contributor
Total hack
Joined
Jun 4, 2002
Messages
37,111
Stock rubber are just rubber. No offset. Only when you go to poly did offset actually exist.

Why would ford put offset rubber bushings in? These were engineered to go down the assembly line as fast and efficient as possible. The wedges are welded on according to production specs. There is no need for an offset bushing as 0° is best for production, just put the bushings in and not have to line up any dots, marks, or anything else. Just one rubber per side and ram the bolts home.

2° poly bushings are as close as you can get to 0° bushings without actually going to original bushings.

Actually there is a way to cheat poly bushings to be 0° bushings. Install one bushing per side upside down. That puts both thick parts on the top or on the bottom. This cancels out the rotation of a thick side on the bottom front and the top rear that the offset bushings create.
 

garberz

Bronco Influencer
Joined
Jun 24, 2007
Messages
6,864
Loc.
Conejo Valley, Ca.
James Duff came up with the idea to offset the “C” bushings, after seeing what longer coil springs were doing to the front end geometry.

Mark
 

nvrstuk

Contributor
Just a Bronco driver for over 50 yrs!
Joined
Jul 31, 2001
Messages
10,621
Loc.
PNW
Mark beat me to it...good job.

James Duff and SEMA and 30+ yrs ago... I'm not sure of the date but between degreed C bushings and poly track bar bushings...we owe alot to that ingenious fella!!

Ever try pressing in a rubber OE track bar bushing 40 yrs ago?? HAHA, I want to bring my video camera... at least with the tools we had back then... :cry:
 

nvrstuk

Contributor
Just a Bronco driver for over 50 yrs!
Joined
Jul 31, 2001
Messages
10,621
Loc.
PNW
Mark beat me to it...good job.

James Duff and SEMA and 30+ yrs ago... I'm not sure of the date but between degreed C bushings and poly track bar bushings...we owe alot to that ingenious fella!!

Ever try pressing in a rubber OE track bar bushing 40 yrs ago?? HAHA, I want to bring my video camera... at least with the tools we had back then... :cry:

This could be a Todd Z question...when did Jim introduce the degreed bushings back at SEMA? (wasn't it at SEMA-best new product?)
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
Ever try pressing in a rubber OE track bar bushing 40 yrs ago?? HAHA, I want to bring my video camera... at least with the tools we had back then... :cry:

Yeah, went to poly that same day because those suckers were NEVER going to go in.
I've still got them in my parts drawer. Bought new from Ford in about '77 or so.

Paul
 

toddz69

Sponsor/Vendor
Bronco Guru
Joined
Nov 28, 2001
Messages
11,222
Mark beat me to it...good job.

James Duff and SEMA and 30+ yrs ago... I'm not sure of the date but between degreed C bushings and poly track bar bushings...we owe alot to that ingenious fella!!

Ever try pressing in a rubber OE track bar bushing 40 yrs ago?? HAHA, I want to bring my video camera... at least with the tools we had back then... :cry:

This could be a Todd Z question...when did Jim introduce the degreed bushings back at SEMA? (wasn't it at SEMA-best new product?)

Off in the weeds in this thread...I didn’t know for sure so I asked Monster Mike. He said 78-79 for the 2-4 deg bushings and around 86 for the 6.25 ones. I know James won a SEMA award for his TTB caster/camber bushings in the early 80s - not sure if he won something for the C-bushings. Stroppe built some replacement bushings for his race Broncos in the early 70s too - not sure if they added any caster or not though.

Todd Z.
 
Last edited:

nvrstuk

Contributor
Just a Bronco driver for over 50 yrs!
Joined
Jul 31, 2001
Messages
10,621
Loc.
PNW
Thanks Todd...Appreciate a "historian" correcting my attempts at recollecting correct dates... :)

Anybody else try pressing in rubber track bar bushings? Dang, we tried several times after hearing a story thatone local guy at the Ford garage wa successful...once!!!
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
When I could not do it I took it to two local machine shops with presses, and neither of them could do it either.
However there have been at least a couple of forum members (either here, or over on broncofix) over the years that said they did it easily.
I wonder if in later years they made the sleeves smaller in order to facilitate them fitting?

Paul
 
OP
OP
J

jckkys

Contributor
Bronco Guru
Joined
Mar 15, 2012
Messages
5,221
I still don't make sense of the idea that poly C bushings need an additional 2 degrees to work with no lift. Obviously the rubber ones are 0 degrees, as there is only one part number for all 4, ie.C6TZ-3B203-A. I never implied otherwise. Do the 2 degree poly bushing makers assume there is some lift? The OE rubber bushings have always worked well for me with no lift. The steering returns to straight quickly after a turn, so more caster doesn't seem to offer much.
 

Justafordguy

Bronco Guru
Joined
Sep 26, 2009
Messages
6,255
Anybody else try pressing in rubber track bar bushings? Dang, we tried several times after hearing a story that one local guy at the Ford garage wa successful...once!!!

I remember back in 1980 how much trouble it was trying to replace the bushing on my 73, the factory bushing was gone and it had death wobble really bad. The only replacement I could find was the factory rubber one from Ford. I struggled with that thing all afternoon but finally got the new one in. I remember the new one was almost destroyed by the time I got it in there but it was way better than what I had before and the death wobble was gone. ;D
 
OP
OP
J

jckkys

Contributor
Bronco Guru
Joined
Mar 15, 2012
Messages
5,221
I started this thread to find info on rubber vs. poly C bushings with no lift. That info was never even discussed let alone answered. Was the subject matter too difficult?
 

toddz69

Sponsor/Vendor
Bronco Guru
Joined
Nov 28, 2001
Messages
11,222
I started this thread to find info on rubber vs. poly C bushings with no lift. That info was never even discussed let alone answered. Was the subject matter too difficult?

Apparently so. I think Tim (Broncobowsher) answered your question in post #2 with about the best possible info you'll find.

Todd Z.
 
OP
OP
J

jckkys

Contributor
Bronco Guru
Joined
Mar 15, 2012
Messages
5,221
With no help or information on the subject of my thread, I've decided to go with rubber C bushings. The 50 yr. old rubber originals were still in good shape and poly has proven a poor material in almost all applications. I'm back to using poly solely for sway bars.
 
OP
OP
J

jckkys

Contributor
Bronco Guru
Joined
Mar 15, 2012
Messages
5,221
Todd, I appreciate your answer, but Broncobowsher simply restated the information in my OP. The unanswered question is; why a stock suspension needs 2 degrees of additional camber in the poly bushings when the rubber bushing have 0? I know 0 degrees works from experience. Where does this perceived need for more camber come from?
 

garberz

Bronco Influencer
Joined
Jun 24, 2007
Messages
6,864
Loc.
Conejo Valley, Ca.
Todd, I appreciate your answer, but Broncobowsher simply restated the information in my OP. The unanswered question is; why a stock suspension needs 2 degrees of additional camber in the poly bushings when the rubber bushing have 0? I know 0 degrees works from experience. Where does this perceived need for more camber come from?

You mean Caster, I’m sure. More caster over stock will in theory will give you better road manners while driving straight down the highway. Less caster was needed when the vehicle wasn’t equipped with power steering, so you could turn the wheels at slow speed. I’m thinking bias ply vs. radial tires may be a reason for less caster back in the day also. I’ve recently learned that the larger dia. your tire, the less Caster is required.

Mark
 

Bronco4x4

Sr. Member
Joined
Dec 21, 2009
Messages
621
I think you mean caster angle instead of camber. If the EB tracks well in addition to the steering wheel returning after turns you should be good. Not sure if zero degree poly C bushings exist and may be why 2 degree are suggested. Check the vendors.
 
OP
OP
J

jckkys

Contributor
Bronco Guru
Joined
Mar 15, 2012
Messages
5,221
True I did mean caster. My point is, with 0 additional caster contributed by the C bushings, the driving characteristics indicate no more is needed. In fact the caster is within spec. For some unknown reason the makers of poly bushings have decided more caster is advantageous, even if it puts the caster out of spec. To create a 0 degree poly mold can't be cost prohibitive when they did make 2, 4, and 7 degree bushings.
 

nvrstuk

Contributor
Just a Bronco driver for over 50 yrs!
Joined
Jul 31, 2001
Messages
10,621
Loc.
PNW
Cranky today? :)

Check out the differences between caster spec's on 1960's trucks with bias ply or nylon tires as OE equpment and mostly manual steering.

Check out the differences in caster specs on '80's and later trucks with radial tires as OE equipment and mostly power steering.

SO, if you have a vehicle that was built and or designed in the '60's and are now NOT using OE spec'd tires and NOT using manual strg then to have the vehicle handle, track, strg wheel return to top after turning, ease of turning (pwr/manual), eliminate/reduce wander... then you INCREASE caster to what the industry in general is spec'ing out for almost ALL new trucks...that is a higher caster spec.

That is my understanding as to why the poly bushings only came in 2deg, not 0 degrees...because they were designed partially to increase caster because of: prolifent use of radials on the market, power strg becoming extremely popular in trucks...

Rubber was stock because it was designed for manual strg systems, nylon/bias tires, etc.

How many vehicles run nylon tires and manual strg as OE equipment today?
 
OP
OP
J

jckkys

Contributor
Bronco Guru
Joined
Mar 15, 2012
Messages
5,221
My new '77 came with radial tires and power steering while keeping the same alignment specs as the '66-'76 Broncos. The '78-'79 specs are different. So is the rest of the truck. The '80 up Broncos are another totally different truck with an independent front suspension. I don't use generalities but specifics. My new '77 with the same alignment specs as '66-'76 Broncos handled better than my new '74 or any other EB I drove. If my '77 built with radials and power steering needed different alignment specs, Ford would have written them, just as they did with later F150 type Broncos. I can't believe Poly or Energy had a real reason to think another 2 degrees of caster is always a benifit. The later models were far heavier, a better reason to increase caster than the tires and power steering that the EBs already had. The '78-'79 Broncos had the wedges welded on the axles with the added caster built in. If the '76-'77s needed more caster they would have done the same for them. Beyond sway bar bushings polyurethane has proven to be a cheap replacement in every sense of the word.
 
Top