• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Question on Petronix 2 upgrade

salineriverman

Jr. Member
Joined
Dec 29, 2021
Messages
54
Loc.
Wilmar
Having issues with old points in 71 bronc-
Looking to upgrade to pointless Distributor - Anyone use the Petronix D130700 flamethrower on their 302 - 4 barrel carb which doesn’t have a body lift?? Just making sure it will clear hood before I order. Thanks in advance.
 

mhinchliffe

Jr. Member
Joined
Dec 21, 2018
Messages
117
I put the ignitor only in my distributor. Starts like a modern fuel injected one now. It used to take longer to start with the conventional points. Much smoother idle too. Stock 2v carb.
 

fluffybunny

Full Member
Joined
Oct 28, 2015
Messages
219
I put a Pertronix ignition along with a Flamethrower 40011 coil on mine November 2021. Stock distributor. No issues. I tried looking up the number of the Pertronix which I ordered off of Amazon and it's not showing any other any infor other than 8 cylinder Ford ignition. It's really easy to install. I just have a jumper wire bypassing the resistor on the firewall and i keep the points in the glovebox just in case I need it.
 

Attachments

  • Screenshot_20230111_080313_Gallery.jpg
    Screenshot_20230111_080313_Gallery.jpg
    69.8 KB · Views: 74

EB70

Sr. Member
Joined
Jun 9, 2006
Messages
730
I put a Pertronix ignition along with a Flamethrower 40011 coil on mine November 2021. Stock distributor. No issues. I tried looking up the number of the Pertronix which I ordered off of Amazon and it's not showing any other any infor other than 8 cylinder Ford ignition. It's really easy to install. I just have a jumper wire bypassing the resistor on the firewall and i keep the points in the glovebox just in case I need it.
Ditto on all counts except I didn't do the coil. I carry the old points just in case, but I don't really think I need to.
 
OP
OP
salineriverman

salineriverman

Jr. Member
Joined
Dec 29, 2021
Messages
54
Loc.
Wilmar
Thanks - I ordered the 91281 kit and flamethrower coil and Pertonix 2001 relay today - hopefully it’ll solve some of my hard to crank issues.
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
It might... But it really depends on what your issue is.
When you say "hard to crank" is it literally cranking hard and straining the starter motor? Or is it just not starting quickly like it should?
In other words, does the engine crank slowly, or does it just take awhile of normal cranking for it to fire?

Modern points, but especially condensers are acknowledged to more often than not be crap. So it's a crap shoot putting in new parts around the original designs because it's hard to find anyone that builds them to the same old quality we used to know.
Making the Pertronix stuff an even better upgrade than it was twenty years ago!

Paul
 
OP
OP
salineriverman

salineriverman

Jr. Member
Joined
Dec 29, 2021
Messages
54
Loc.
Wilmar
Yea
It might... But it really depends on what your issue is.
When you say "hard to crank" is it literally cranking hard and straining the starter motor? Or is it just not starting quickly like it should?
In other words, does the engine crank slowly, or does it just take awhile of normal cranking for it to fire?

Modern points, but especially condensers are acknowledged to more often than not be crap. So it's a crap shoot putting in new parts around the original designs because it's hard to find anyone that builds them to the same old quality we used to know.
Making the Pertronix stuff an even better upgrade than it was twenty years ago!

Paul
- it doesn’t crank very quick - it takes a while - it’ll sputter and backfire some.
We ran some new fuel lines , installed a new fuel pump and blew out the fuel lines and got a flow of gas to fuel pump.
Once we get the ignator kit installed hopefully it’ll crank and run better.
It’s still got a little miss in it - Maybe this will get it going.
We put a new Winch on this week and modified the old Warn bumper so Harbor Freight 12000 lb winch would work - it looks pretty good . Still needing to repair top and paint job. Gas mileage is terrible - must be getting 8 miles to gallon!!!😩😩. Wonder how much it’d improve if had 411 gears - currently running 456’s
 

fluffybunny

Full Member
Joined
Oct 28, 2015
Messages
219
I get 8-9 mpg with 350 gears and 33's. I only use ethanol free gas that's $4.50 gallon while the 87 ethanol fuel is $3.25. That's the price you pay for thumbs up and compliments everywhere you go.
 
OP
OP
salineriverman

salineriverman

Jr. Member
Joined
Dec 29, 2021
Messages
54
Loc.
Wilmar
Than
I get 8-9 mpg with 350 gears and 33's. I only use ethanol free gas that's $4.50 gallon while the 87 ethanol fuel is $3.25. That's the price you pay for thumbs up and compliments everywhere you go.
Thanks , I was hoping for 10 to 12 mpg but with present gears probably not going to happen. I only run ethanol free fuel too! Most stations here only carry premium ethanol free. I have a new Eldelbrock 4 barrel carb and my brother had put a larger cam in motor when it was rebuilt in mid to late 80’s. My tires are Cooper 31.50 x10.50 - 3 speed hurst
Got a miss in engine - hopefully new pertronix kit will fix. If not back to the head scratching!
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
Depending upon your tire size and engine configuration, you might find the 4.56 mileage better than the 4.11! It all depends.
But with mine as a daily commute driver for many years, 8 to 10 miles per gallon around town was normal. Usually the lower…
And I checked every tank back then !
Mine had 4.11 and 32 inch tires. Highway mileage varied between 12 and 17 depending on conditions and which carburetor I had, but average was about 15 around town.
Is that what you’re checking? How long does it take to warm up to the point that you start to drive?

And slow cranking won’t necessarily change between ignition types.
Generally the only ignition issue you experience slow cranking under is too much spark advance. And you can have that just as easily with a Pertronix or any electronic ignition, as well as points.
What is your overall engine configuration? Stock? Modified? Carbureted or fuel injected?
What is the condition of your wiring in general? Especially the battery cables?
How old is the starter?
Do you have a timing light and have you checked the timing yet?
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
Oh, and I’m not trying to talk you out of the Ignitor. I think it’s a great set up and I have used them myself as well.
Just trying to get you to check some other things and hope you have a timing light because once you install a new distributor or new ignition inside the original distributor, you’re going to need to check the timing anyway.
No matter how careful you are during the install.
 
OP
OP
salineriverman

salineriverman

Jr. Member
Joined
Dec 29, 2021
Messages
54
Loc.
Wilmar
I’ve installed a new-rebuilt starter, new plug wires , plugs, new Eldelbrock 4 barrel carb, new fuel lines , new rear tank and cleaned front tank, fuel pump, points and condenser.
Has a 302 with a fair sized cam - new 31x10.50 Cooper tires.
I’ll get my mechanic to check timing and make sure all cyl are firing properly .
I’ve also installed new brakes, power steering and tilt steering , new shorty headers and exhaust and new alternator.
It’s cranks with ease once it warms up - but as I said earlier it’s a bugger to crank. I do think the timing may be off a bit - I did find the negative battery cable was a little loose. Still got to install two fenders and new fender flares and decide what to do about top that has rusted out on back and over drivers side door. Then the paint job.
 

mhinchliffe

Jr. Member
Joined
Dec 21, 2018
Messages
117
Just my opinion here but to run ethanol free getting 8-9mpg is a waste of money. The gas isn't in there long enough for phase separation to set in and with all the work you've done I'm gonna say your soft lines are ethanol resistant. I have noticed that the E free fuel will act like it's flooded/vapor locked when trying to start after it's hot.
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
Quite a list of done's and still-to-do's it looks like!
A great head start.

Just to make certain we're all on the same page again though, when you say "slow" when cold, you mean the engine turns over very slowly such as with a weak battery? Or slow, as in it takes longer for the engine to fire?
Just making sure.

Don't scrimp on the battery cables. Use at least 4ga, but 2ga is better. Many of us use custom cables made up of anything from 1ga or 0ga standard cable, to 1/0 welding cable.
No trouble with size in those cases!
But I believe the originals were 6ga which is perfectly fine when new and with a stock engine. But for more overhead capacity with higher compression, older starters, more ignition timing, deteriorating cables over time, and anything else you can think of, bigger is naturally better when it comes to battery and starter cables.
Even the short one can benefit, but it's all about the length. And anymore, 2ga copper is standard offerings in most auto parts stores.
Easy and inexpensive.

Not saying that's your only issue with the slow cranking, and the slow when cold thing is odd. More often than not if it's ignition timing too far advanced, it gets worse when hot.
So perhaps there is something else afoot here.
Still, doesn't hurt to verify.

Good luck.

Paul
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
Oh, and I don't suppose there's a chance that your brother still has the cam card, or part number for the cam he installed?
Long shot after all these years I'm sure, but hey, sometimes you get lucky!

Paul
 
OP
OP
salineriverman

salineriverman

Jr. Member
Joined
Dec 29, 2021
Messages
54
Loc.
Wilmar
Thanks Paul , it’s slow to crank as taking a long time for the engine to fire .
It’ll then die if you don’t keep it revved up for a few minutes - Not sure on cam size and no one knows what he put in since he passed away in 2019.
The engine was pulled from a wrecking yard and he had a mechanic who I don’t know rebuild the engine in mid to late 80’s. It doesn’t have a lot of miles on it since it was only used during deer season and turkey season. The bad side to that was it stayed outside at the deer camp in the elements . It hadn’t been driven since 2009.
I’ll replace battery cables this week and try and get a timing light. Thanks
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
Well, the battery cables will probably be a benefit, but now that I know you're speaking of slow to fire rather than slow cranking, the new ignition will likely help a bunch.
Can also be carburetor related especially when speaking of an engine that had not been run much (if at all!) over the years. So time will tell.

Probably take a few all-of-the-above tests and adjustments and cleanings and tweakings to get it back to snuff.

Have fun in the process!

Paul
 
Top