• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Sheared Banjo Bolt

SeanT4x4

Full Member
Joined
Oct 2, 2013
Messages
185
So yesterday after work I was bouncing on the front end to check for bump steer, after reading about that on here (different problem). I noticed a couple drops of brake fluid leaked out of the brake line where it meets the caliper. I had done a disk brake conversion about two months ago and figured those copper washers hadn't smashed enough for it to seal properly. Figured I'd give it a little more torque... bad idea. I sheared the head off and leaked brake fluid all over the garage. Two question, whats the best way to get the rest of that banjo bolt out? (I've never done it before) Its a chevy disk brake conversion from Toms, what do I tell the guy at O'reileys as far as make and model so he can get me the right banjo bolts?
 

half cab

Contributor
Guru Bronco
Joined
Dec 8, 2010
Messages
16,311
I broke one off couple yrs ago n picked up a bolt abstract tool from HF cheap n it worked. Carry the sheared bolt to parts store with ya they can match it .

BTW might want to get a new crush washer to go back with the new banjo bolt .
 

surfer-b

Contributor
Bronco Guru
Joined
Sep 7, 2006
Messages
3,013
Its prob not worth the trouble of trying to remove it, you can get them for bout $20 a piece, you will spend more time and $ trying to remove it. Just go to the parts store and get a caliper for a 75 chevy 1/2 ton 4x4 blazer or truck, and pic up another bolt and couple of washers. Take the old caliper with you and make sure to get the correct side.
 

Apogee

Contributor
Bronco Guru
Joined
Nov 26, 2005
Messages
6,348
Loc.
Tangent, OR
Once the head is gone and the hose is off, just spin out the threaded shank with pliers or vice grips...it shouldn't be tight since there's no preload on it anymore, unless it's rusted in place.

The old Chevy D52 calipers use a 7/16-20 banjo bolt...make sure you get one that's long enough to have at least 1.5 X diameter thread engagement and you should be good to go.
 
OP
OP
SeanT4x4

SeanT4x4

Full Member
Joined
Oct 2, 2013
Messages
185
Ill pick up a set from harbor freight and give that a shot before I think about replacing a two month old caliper. Also bring the bolt from the other side to match and get all new washers. What are these things supposed to be torqued to?
 

BRONCROB

Bronco Guru
Joined
Nov 24, 2010
Messages
1,613
Loc.
WISNER LA.
If only the head broke off you can grab the shank with pliers and take it out that way.If it broke off flush you may want to try a torx type bit inside the bolt hole.I have done that a few times.You need to make sure the bolt wasn't hitting something causing the leak or it will happen again.
 

Apogee

Contributor
Bronco Guru
Joined
Nov 26, 2005
Messages
6,348
Loc.
Tangent, OR
Ill pick up a set from harbor freight and give that a shot before I think about replacing a two month old caliper. Also bring the bolt from the other side to match and get all new washers. What are these things supposed to be torqued to?

Torque values vary depending on the application, however most 7/16-20 banjo bolts can be safely torqued to about 25 ft-lb without risk of failure. If you're having a hard time getting them to seal at that point, replace the copper crush washers with new ones or anneal the ones you have with a torch. I've found that some of the cheap crush washers available today are not fully annealed which can make them less compliant when trying to get them to seal. Rather than trying to find quality crush washers, easier said than done, I'll just heat them with a torch until they're rosy and then let them air cool.

If the sealing surface on the caliper has any major defects, then nothing on your part will get it so seal properly.
 

half cab

Contributor
Guru Bronco
Joined
Dec 8, 2010
Messages
16,311
I have took needle noses plyers n held the crush washers in a gas heater when a torch wasn't available n that worked pretty good.
 

Rustytruck

Bronco Guru
Joined
Feb 24, 2002
Messages
10,872
Should be no load on the broken bolt unless you didn't use the 2 copper washers or the bolt was too long. in as much if you have an old file tap the shank of the file in the hole and twist that broken end out. You may be able to use a flat blade screwdriver if the tip fits in the hole and the blade width flairs out. 2 months old the threads should not be locked tight.
 
OP
OP
SeanT4x4

SeanT4x4

Full Member
Joined
Oct 2, 2013
Messages
185
Thanks for the help. I had both washers on but couldn't get it to seal. Thanks for the tip on heating the washers. I have a torch and will give that a shot before installing the new set.
 
Top