• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Sticky throttle??

Hawkdoc

Contributor
Full Member
Joined
Sep 1, 2006
Messages
281
Loc.
Huntsville
Having a problem with a TA470 on a mildly built 302. Every time I come up to a stop, I have to "bump" the throttle to get the idle down. Getting to be a real PITA. Any ideas on cause?

Thanks
Hawkdoc
 

wildbill

Old Bronco Guy
Joined
Jun 29, 2001
Messages
6,890
:p :p :p Stiffer return spring should do it and look and see that there isnt any burs on it or a little bent good luck.%) %) %) Bill %) :cool: ;D
 

airman

Contributor
Bronco Guru
Joined
Nov 26, 2003
Messages
1,843
Pull the linkage off of the carb and operate both the carb and the linkage by hand. Its probably in the linkage but check the carb just in case. I had a carb gasket do something similar once on the choke side. Make sure there is no rubbing or bumping anything. Look under the dash too.

Are you using two springs?
 

broncnaz

Bronco Guru
Joined
May 22, 2003
Messages
24,342
Check and lube all the linkage all the way back to the pedal and install a stronger or second spring.
 

Broncobowsher

Contributor
Total hack
Joined
Jun 4, 2002
Messages
37,111
Also check the air cleaner, they have been known to hang a throttle.
Are you using linkage or cable?
I would avoid an overly stiff spring, that often just masks the problem until it gets worse. It also puts a lot of stress on the throttle shaft bore causing premature wear.

The return spring on the carb should be enough to return the throttle closed, the extension spring is a back-up. It also adds to the "feel" of the accelerator to keep it from feeling too light.

An odd one that is similer...
Friend had a BUILT AMC 401. almost 700 HP on motor alone. BIG roller cam. The distributer advance would fight the carb at idle. Set the engine to idle then after reving it the RPMS would stay up. What was happening was the advance would kick in, bring the revs up and not let the engine come back to an idle. Back off the idle screw to slow it down and it would drop enough to pull in the advance and bring the idle down to a stop. We just needed to tweak the advance a hair (don't remember which way we did, think it was tighter spring or lighter weight) to get it right. But that was on a stupid big motor that still had a lope to it even at 3000 RPM, didn't run good until over 5000. Was kicked off tracks for pushing a full steel car under 10's
 
OP
OP
Hawkdoc

Hawkdoc

Contributor
Full Member
Joined
Sep 1, 2006
Messages
281
Loc.
Huntsville
I am running a FOMOCO drop base air cleaner and it has plenty of clearance. I am only running one spring at this time. It strange that I just have to "barely bump" the throttle to get it to drop. I checked the linkage last night and felt fine but everyhting got oiled a little anyways. I will try and get a shorter spring on the way home tonight.

Hawkdoc
 

airman

Contributor
Bronco Guru
Joined
Nov 26, 2003
Messages
1,843
With the two springs, make sure the smaller one goes inside of the bigger one so they dont catch on eachother.

On the holley make sure the choke side of the throttle is not rubbing on something too like a gasket.
 
OP
OP
Hawkdoc

Hawkdoc

Contributor
Full Member
Joined
Sep 1, 2006
Messages
281
Loc.
Huntsville
I will double check it tonight. Need to try NApa for springs on the way home.

Hawkdoc
 
Top