• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Surprise under valvecover

OP
OP
ribbits

ribbits

Jr. Member
Joined
Jan 21, 2015
Messages
130
"The special washers are critical to use and are orientation specific, they have a stepped shoulder diameter and must be installed correctly - large diameter down first, smaller diameter against the nut. The rocker stud is stepped and has a larger diameter at the head than at the thread, the washer has the stepped hole so it clears the unthreaded shank portion of the stud but has a tight fit on the 5/16 thread."

Also,,If you get a magnifying glass you can see has a small letter "T" stamped on the small diameter side and I'm assuming that stands for top "TOP"..
Thanks again
 

DJs74

Bronco Guru
Joined
Apr 1, 2014
Messages
1,135
"The special washers are critical to use and are orientation specific, they have a stepped shoulder diameter and must be installed correctly - large diameter down first, smaller diameter against the nut. The rocker stud is stepped and has a larger diameter at the head than at the thread, the washer has the stepped hole so it clears the unthreaded shank portion of the stud but has a tight fit on the 5/16 thread."

Also,,If you get a magnifying glass you can see has a small letter "T" stamped on the small diameter side and I'm assuming that stands for top "TOP"..
Thanks again

Could be, I've never noticed a "T" but it makes sense.

If you decide to go with polylock nuts, you'll like them - they are far superior over staked / interference type rocker nuts IMO.


DJs74
 

Andycapp

New Member
Joined
Feb 15, 2014
Messages
16
Loc.
Puyallup. WA
Nothing more to ad, think the issues been covered. But a question... So you just heard a tapping noise? Was this a sudden WTF IS THAT or just a little noisy and worth taking a look. Just curious. What would be the Carnage if it were ran this way for any length of time?

Sent from my E6790TM using Tapatalk
 

Steve83

Bronco Guru
Joined
Jul 16, 2003
Messages
9,360
Loc.
Memphis, TN, USA, Earth, Milky Way
Can't it just be loose rocker nut?
Not with hydraulic lifters. The nut would have to be visibly high before it would exceed the lifter's automatic adjustment range. And because of all the other details ribbits listed, I assumed he did NOT notice the nut being high on the stud. He said it had no torque, but not that it was high.

And reading all the other warnings people are posting about converting to individually-adjustable rockers just makes me that much happier to keep factory HLAs in everything I drive. My Bronco's engine has somewhere around 800Kmi without rebuild, and my CV ~350Kmi. Stock parts work, when properly maintained.
 

pcf_mark

Bronco Guru
Joined
Jun 11, 2010
Messages
3,697
If it is positive stop rockers then it could be a loose nut. The nuts should not be re-used. One turn out the rocker will flop like a fish and be tricky to see in the photo. They should be tight.

If it is been converted to adjustable then I agree that the nut would not be torqued it is adjusted to lash / pre-load.

Once the OP knows for sure which is in there maybe we can throw some more confusion at him!
 
OP
OP
ribbits

ribbits

Jr. Member
Joined
Jan 21, 2015
Messages
130
Nothing more to ad, think the issues been covered. But a question... So you just heard a tapping noise? Was this a sudden WTF IS THAT or just a little noisy and worth taking a look. Just curious. What would be the Carnage if it were ran this way for any length of time?

Sent from my E6790TM using Tapatalk

Actually I pulled it into the shop and closed the doors.. Don't remember why but I fired it up and raised the hood.. being in the enclosed place it sounded pretty loud and I'm almost legally deaf ... I couldn't even tell what side if the engine it was on but thats not saying much. So I grabbed the engine stethoscope and pinpointed it at the #7 cylinder.. Don't think it was doing it very long but I'm not sure.. I've actually only driven this thing but about 3 miles since I bought it... I took a young guy who is a mechanic type with me during the pre buy and he never noticed it either? The next time I saw the truck (week later) I was loading on on the trailer... The little driving I did it never got over 2000 RPM's for sure..
I was planing on finalizing this thing up today, but unfortunately we had a death in the family and my plans got changed... Have fresh lock nuts in hand and hoping I can get back on it soon and will report back Thanks to all!!
 
OP
OP
ribbits

ribbits

Jr. Member
Joined
Jan 21, 2015
Messages
130
I found some MIL spec 5/16"-24 acorn type lock nuts listed as "for extreme vibration" on Mcmaster-Carr's site.. Ordered them and they do seem to offer more resistance when screwing them down than the staked ones and are also much taller and don't have inserts. These guys have about every kind of nut and bolt you could imagine.. They also had some of the same nuts listed as jam nuts (half as tall) and I got some of those too, but don't think I will need them?? Anyway,, readjusted valves per adjustable valve procedure and installed net new nuts??? Cranked up and was quite as a mouse... I guess Time will tell if it will stay that way... Thanks to all for the great data.. Ohhh, by the way I found 3 spark plugs that were only finger tight, wonder they didn't blow out?? Found out why when I was re-installing them, the custom headers made it kinda tough,, but they are all tight now... Thanks again..
 
Top