• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Tech Lessons (Newbie Mistakes)

Bronco Junkie

So Cal Broncos
Joined
Feb 29, 2012
Messages
3,246
Always wear safety glasses when someone is welding on the inside and you are underneath holding the dolly.
 

69red

Full Member
Joined
Dec 17, 2004
Messages
239
Loc.
Cochrane, AB,CAN
when you are separating the 3spd transmission from the transfer case, make sure you dont pull the transmission ouput shaft out :-[
 

ep67bro

Contributor
Bronco Junky
Joined
Aug 28, 2008
Messages
3,873
Loc.
Easton, MD
When using a cut off wheel watch where the sparks are going they will set something on fire!
 

broncobilly72

Full Member
Joined
Nov 8, 2010
Messages
349
When rebuilding an engine, be sure to put the oil pan drain plug in before adding oil. Clean, new oil is just as hard to clean up as dirty old oil from the concrete floor.
 

NYLES

Bronco Guru
Joined
Aug 13, 2004
Messages
9,846
Not mine, but I was helping...make sure the torque converter is fully seated prior to transmission installation and engine start-up or you'll lose the tabs on the front of the pump.

been there done that.......dont forget the flexplate
 

savage

Bronco Nut
Joined
Apr 18, 2007
Messages
2,483
Loc.
Renton
I was heading north to deliver.That week tractor with BIG CUMMINS DEISEL was serviced,well allways double check oil plug,you know whats next 14 plus quarts from front to back,but I shut engine off before any damage ,good for owner and mechanic that service the truck,just long day for me.
 

Rustytruck

Bronco Guru
Joined
Feb 24, 2002
Messages
10,872
Adjust your points on the wide side of tolerance so you dont have to adjust them all the time.

As for window glass always use a new gaskit and when removing the old window cut off the gaskit flange with a razor knife to make removal easier and no chance of breakage.

aluminium intake manifolds and gas leaks are not compatable.
 

Jdgephar

Bronco Guru
Joined
Sep 25, 2012
Messages
1,526
Not mine, but I was helping...make sure the torque converter is fully seated prior to transmission installation and engine start-up or you'll lose the tabs on the front of the pump.

Did this myself, but thankfully engine would not crank, so no damage and I was able to put the torque converter all the way on.

Also, distributor stabbed with the crank 180 deg. out of time (TDC of exhaust)

Next....make sure fan clears all hoses (specifically radiator hoses) before starting the engine again.
 

RnrdTheFox

Sr. Member
Joined
Dec 4, 2005
Messages
727
Loc.
Superior, CO
When you are 15 and trying to debug a fuel problem on your carb, don't forget to reconnect your fuel line before cranking. Because when you keep cranking it and it decides to backfire, you are on fire!

Yep, real story. I was lucky that my dad was sitting in is truck reading something and was a vol fireman. He had a fire extinguiser in is truck and put it out before it did real damage other than melt a few hoses and wires.
 

Pat'sBronco

Jr. Member
Joined
Nov 13, 2009
Messages
87
Loc.
Murfreesboro, TN
Always remember to put the transfer case in 2 hi or (anything other then neutral) after you reinstall everything when replacing the clutch. (Before you freak out);)
 

pa69broncoguy

Sr. Member
Joined
Sep 6, 2011
Messages
566
always check all your oils after a complete restoration, belive it or not if you forget gear oil in the rearend it will lock up and trash everything in a very short distance, dont ask me how i know this:)
 

Master Chief

Contributor
Bronco Guru
Joined
Nov 24, 2006
Messages
1,312
Did this myself, but thankfully engine would not crank, so no damage and I was able to put the torque converter all the way on.

Luck was on your side. This happened around 1985 when I was stationed in Maryland. We messed with it for hours then decided to pull the transmission out again. Brought it to a shop called Drive Line north of Lexington Park, they quickly explained what happened. Cost my buddy a new pump and whatever the shop fee was to replace, I call it a free life lesson for me.
 

707Bronk

Sr. Member
Joined
Mar 18, 2012
Messages
590
After you get home from a tire rotation and park your vehicle for the night, make sure to check the lug nuts before you drive it the next day.

Yup, some years ago I was driving in downtown San Luis Obispo and next thing I know I am watching my tire and wheel roll past me into an intersection. Luckily enough it rolled right through the intersection traffic at a fairly good clip and didn't cause any damage to anyone or anything...my drivers side rear drum and backing plate were toast though.
 

Tulsa76bronco

Sr. Member
Joined
Apr 23, 2013
Messages
635
Make sure u pay attention to which wire u put back on your battery. Red is positive, good thing it only cost me a new regulator
 

mlake01

Jr. Member
Joined
Oct 1, 2012
Messages
61
I've owned my Bronco for 17 years (plus I'm getting old) so I'm hardly a newbie!

Should someone start a new thread "Tech Lessons (Veteran Mistakes)"? I may be able to make a contribution or two...:-X

3 broncos over 30 years - made my living as a truck mechanic for years - here's a veteran screw up for you: Always put the drain plug back in before putting fresh oil in...

I noticed the drain plug sitting on the radiator at about the same time the puddle actually reached my feet!
 
Top