• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Temperature Gauge help ..PLEASE

doublehfarm

Jr. Member
Joined
Jan 2, 2021
Messages
65
Loc.
Alabama
Frustration at finest....
I replaced sending unit twice and have went back to the original one as well.. new gauge and have put new wire to check guage still nothing..

have tired grounding sending unit wire but gauge wont move .. any other test I can do to pinpoint my problem??

All other gauges work fine. thanks
 

66CTBronco

Jr. Member
Joined
Nov 18, 2020
Messages
92
Loc.
New england
Battery connection at the gauge ok from the gauge cluster voltage regulator? Grounded the gauge at the gauge to test the sending unit wire?
C
 

savage

Bronco Nut
Joined
Apr 18, 2007
Messages
2,483
Loc.
Renton
I kept having issues without the gauge in my 74. Is your sending unit screwing it to a metal intake or a aluminum intake? Is this a stock gauge or after market?
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,651
If the pressure and fuel gauges work, then you know the regulator is fine.
If the gauge does not peg to full when you ground the wire then either the gauge itself is bad (rare, but it happens) or the input, or output wires are broken somewhere.

If you measure voltage at the input side of the gauge what do you read? If nothing, then the wire is broken between the IVR and the gauge.
If you read a pulsing signal, then measure what is at the output side of the gauge (toward the sending unit) and see if you have a similar signal to the input. IF so, then measure at the sending unit wire. If it's not present, then there is a break in the wire between the gauge and the engine.

What year is your Bronco? If it's a '70 or earlier, triple-check the two rectangular firewall connectors. If a '71 or later, then this wire in question will be on the single flat connector behind the engine. I think it's the red one with the wires for ignition coil and oil pressure as well.

And "speaking of grounds" as we always do... Make sure you have a good body ground directly from the battery (in addition to the main cable to the engine) and a secondary ground strap between the engine and firewall.
This is likely not your issue if your other gauges work. But it's still a worthwhile thing to do.

Paul
 
OP
OP
doublehfarm

doublehfarm

Jr. Member
Joined
Jan 2, 2021
Messages
65
Loc.
Alabama
Thanks for all the help...

Its a 66 . Im going to try to order a sending unit from a supplier today that may fix the problem. will start tracking down the other issues this afternoon... thanks again
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,651
If grounding the sending unit wire does not do anything, then a new sending unit will not do anything either. Even though all the parts are new, something is wrong upstream of the sending unit as you verified by grounding the wire.

Paul
 

66CTBronco

Jr. Member
Joined
Nov 18, 2020
Messages
92
Loc.
New england
Ground the sending unit wire at the sending unit. Pegged gauge the wire is ok sending unit is bad. No peg keep looking. Ground the gauge at the sending unit terminal of the gauge. If it pegs the gauge to sending unit wire is bad, if not keep going. Look for regulator voltage at the sending unit terminal of the gauge. If you see voltage the connection to the cluster regulator is ok, the gauge is shorted and dead. If no voltage check the cluster voltage regulator connection at the gauge.... by default that connection has to be bad. That’s the entire circuit from one end to the other. As dirtdonk said if the other two gauges work the gauge regulator is good.
C
 
Top