• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

third member question

berg bronco

Bronco Guru
Joined
Dec 16, 2008
Messages
1,287
Loc.
franklin NC
I heard a clunking in the rear end so I removed the third member and found a pile of metal teeth in the axle housing! side gears and spider gears!my ring and pinoin look fine. i think its a limitied slip, gears are 456 and I run 35" tires and 20% offroad and 80% on road. what do you guys think is my cheapest and most logical fix? and how do i figure out what kind of carrier i have ?
 

65 mustang

Sr. Member
Joined
Mar 30, 2007
Messages
430
Replace everything including the ring & pinion and axle bearings. The cheepist way is to do it your self or find somebody local. Most LS or Lockers are around 1000. to just swap.The 3rd member is probable a stock unit.The axle ratio is found by jackin up the diff. rotate the drive shaft 1 rotation while counting the number of rotations the tires make. After reading that,sorry If you look into the carrier if you only see the spider gears its open.The locker thing is a little more tricky.I'm not sure really. if you do a search for that i know you'll find it. Scott
 
Last edited:

broncnaz

Bronco Guru
Joined
May 22, 2003
Messages
24,342
To ID what you have or had if it was a limited slip the ring gear bolts are recessed into the cover. If it was a open diff the ring gear bolts are not recessed. typically if the spider and side gears break on a LS carrier the clutch coover will also bust. I've broken 2 trac locs in my 73. They are not the strongest units especailly with big tires. I'm now running a 4 pinion trac loc with a currie billet steel cltuch cover going to see if the 4 pinion holds up or not. I've also reused my gears both times as theres been no actual wear or damage to them because of the breakage.
With your tire size I wouldnt suggest another factory trac loc you need after market or just get a open carrier. mostly it will cost you whatever the diff costs and a set of bearings if you do the rebuild your self.

Here's a pic of a factory trac lock cover see how the cover is recessed for the bolts also note the cracked cover.
 

Attachments

  • clutch cover.jpg
    clutch cover.jpg
    52.8 KB · Views: 46

bax

Contributor
Old Member
Joined
Aug 22, 2005
Messages
14,552
Put new spiders and side gears in and rock on. JBG sells them. You do have to figure out what you have however to get the correct replacement parts.
 
OP
OP
berg bronco

berg bronco

Bronco Guru
Joined
Dec 16, 2008
Messages
1,287
Loc.
franklin NC
broncnaz thanks for the pic! mine is a ls
bax is changing the side/spider gears simple?

I also noticed after looking closer that my pinion gear has a small chip on one tooth:(
 

broncnaz

Bronco Guru
Joined
May 22, 2003
Messages
24,342
Is the chip on the wear surface or the edge? if on the wear surface then iits kinda suspect. if just on the edge no big deal.
Swapping out spider gears is simple pull the ring gear off and the 2 small screws holding the clutch cover on then split the case. I'd go to Currie's site http://www.currieenterprises.com/theres a lot more parts needed then the JBG kit will give you. You may as well put in new clutch packs and preload springs as well.

here's another pic for you its of the trac loc I broke last year had some small chips on the gears but they were not bad reused them.
 

Attachments

  • broke 2.jpg
    broke 2.jpg
    120.3 KB · Views: 61
Top