• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Torker 289

Thatbroncokid

Jr. Member
Joined
Mar 5, 2015
Messages
135
Loc.
BC Canda
Anybody run one of these? I currently have a stock 302 with the motorcraft 2 barrel and stock intake . I have one available to me for pretty cheap and just wondering if its worth my time. I've been having a hell of a time getting my current setup to run properly. It runs great in first gear, (3 speed on the floor), but as soon as i put it in second and let out the clutch, the rpm's drop way down and I have no power uphill or with any kind of load. Don't have anywhere to tap into manifold vacuum thanks to the PO plugging the vacuum tree, and I can't tell if i have a vacuum leak. Don't have any marks left on my balancer either other than TDC, so I can set my timing roughly, mostly by ear. Any insight? Thanks!
 

Amac70

ME
Joined
Mar 27, 2002
Messages
3,269
buy a new tape for balancer, check for vacuum leaks. get it running first before you start changing things.
 
OP
OP
Thatbroncokid

Thatbroncokid

Jr. Member
Joined
Mar 5, 2015
Messages
135
Loc.
BC Canda
Ive checked to the best of my ability for vacuum leaks using carb cleaner and spraying around. Any other suggestions on how to check for them?
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,651
Anybody run one of these?
I have one available to me for pretty cheap and just wondering if its worth my time.

Normally a Torker intake is a higher rpm manifold not really suited for a Bronco. Especially if you have a poor gearing/tire match.
But a good price is a good price, up to a point. Not as tall as some high rpm setups, but might also be trouble if you don't have a body lift.
Might be better than what you have, but most likely it's a pass.

I've been having a hell of a time getting my current setup to run properly. It runs great in first gear, (3 speed on the floor), but as soon as i put it in second and let out the clutch, the rpm's drop way down and I have no power uphill or with any kind of load.

Sounds typical of a Bronco with larger tires and 3.50 gears.
Do you know what you have in the gearing department now? What size tires?

...and I can't tell if i have a vacuum leak.

Have you tried the old spray method? It's very easy to find vacuum leaks usually, with just a can of carb cleaner or similar product. Even WD-40 or water in a spray bottle will often get the job done.
(edit: obviously you do know about that and have done it!)

Don't have any marks left on my balancer either other than TDC, so I can set my timing roughly, mostly by ear. Any insight?

As Amac said, a timing-tape kit would be the best way. But you can also just make your own marks. You can base them off of what others have here I would think. Someone can give you an idea of how far apart 2 or 5 degree tick marks should be. Or you can buy a "dial back" timing light so you don't need anything more than the zero mark.

Since you don't have any other marks, are you advancing your timing by turning the distributor clockwise? And your light is moving to the right of the zero mark, correct?
Just as a guess, I'd say that half an inch to the right of the zero mark is somewhere around 6 degrees or so. That's just from memory though. Doing the actual math it looks like for a 7" diameter damper, roughly every 1/8" around the edge is equal 2 degrees. Hmm, that makes 1/2" 6 degrees like I said!
Saying it that way though (1/8" = 2°) sounds like a big gap for 2 degrees.

Anyway, you get the idear. Easy enough to make something work in this case. Especially since knowing what you have down to the nth-degree is not necessary to just get it running well.

Paul
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,651
If you can't find a vacuum leak with carb cleaner, then very likely you don't have one.
Either that or you're just not spraying in the right places. But if you've sprayed all around the top end of the engine while it was running and did not detect any change in idle speed or quality, I'd say you're doing ok in the vacuum department.

It's still possible to have an internal vacuum leak, under the intake manifold runners, but that's not as common as just the usual garden-variety leak.
Not impossible though!

Paul
 
OP
OP
Thatbroncokid

Thatbroncokid

Jr. Member
Joined
Mar 5, 2015
Messages
135
Loc.
BC Canda
I don't know about the gears actually. I'm thinking it would be whatever came in the truck originally, and I'm currently running 31's . It really hesitates/sputters going up hills (only in second gear) to the point of not being able to maintain the speed limit. Could it be a result of bad timing? Or is that something that would poke its ugly head out in first gear as well? Thanks so much
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,651
Well, it could still easily be timing, but it would usually at least let you know it's not happy even in first gear.
But because first is such a big jump from second, it could act more "normal" in first because it's not struggling as hard.

Your 31's should not be causing the trouble by themselves. They are larger than stock, but only slightly so.
Very likely you have 3.50's, but 4.11's were an option (or even 4.56 if you had a 6-cylinder engine) so you never know.

You could also be suffering from a clogged fuel filter. Works ok under less load (less gas used) but as soon as you go to a higher gear and the load on the engine increases, the fuel delivery is not sufficient. But that doesn't sound quite like it yet either.

What about the trans itself? Have you checked and changed the oil in it? They really should be done at regular intervals, and most do not get done. Perhaps the trans is just starting to fail. I hope not of course! But it's possible.

Back to the engine though, if it's not pulling to it's full potential, then you get even more of the effect in the higher gears. It's just that it doesn't usually come out as such an extreme difference between first and second.

But fiddle with timing, and see what you get.

Good luck.

Paul
 

Nevadasmith

Full Member
Joined
Apr 30, 2016
Messages
182
Loc.
Fallon, Nv
One other thing to try (all of Paul's suggestions are good) is to blow compressed air backwards through the fuel lines, make sure you take the caps off both tanks, a partially plugged fuel line, or selector valve will cause these symptoms, also a clogged power valve in carb. It's probably timing related, but I was having simmilar problems, and found a rag, and some leaves in the main tank, (P/O's do strange things) after cleaning my tank, fuel line, and replacing the 20-40 year old fuel pump, no more problems, good luck!
 

Nevadasmith

Full Member
Joined
Apr 30, 2016
Messages
182
Loc.
Fallon, Nv
Oh, I would avoid that manifold, not a good application for it, actually I would look around for an OE with a casting nuber between c8-d4 with the vacuum stuff still on it, or at least open ports.... just my opinion
 
OP
OP
Thatbroncokid

Thatbroncokid

Jr. Member
Joined
Mar 5, 2015
Messages
135
Loc.
BC Canda
Very interesting . I don't know when the filter was last changed so its definitely worth changinng that out, and ill blow out the lines while im at it. I also find my three speed doesn't like going back into first gear unless im going very slow or stopped at which point its butter smooth. Is it not a synchronized first gear or something?
 

Broncobowsher

Contributor
Total hack
Joined
Jun 4, 2002
Messages
37,114
That intake is poorly named. Should have been called "The Screamer" as it is a higher RPM manifold. Suggest avoid it.
 

Nevadasmith

Full Member
Joined
Apr 30, 2016
Messages
182
Loc.
Fallon, Nv
Very interesting . I don't know when the filter was last changed so its definitely worth changinng that out, and ill blow out the lines while im at it. I also find my three speed doesn't like going back into first gear unless im going very slow or stopped at which point its butter smooth. Is it not a synchronized first gear or something?
Does not want to go to first like grinding, or like its just stops you from shifting. Yeah it's syncro first, but you still have to be kinda close on rpm, or the syncro just stops you from shifting. Try blipping the throttle as you down shift, it takes some finesse, and practice. Grinding could be a symptom of larger problems, I would do an oil change any how, make sure it's not black tar, and no metal comes out. Good luck!
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,651
Yes, these are good shifting transmissions, but they don't just pop into first like some do.
As Nevada said, you either have to blip the throttle a bit, or just wait until you're going slow enough, like you've been doing.

Mine shifted like butter it's whole life, but always needed that matching rpm to get the job done.

Paul
 
OP
OP
Thatbroncokid

Thatbroncokid

Jr. Member
Joined
Mar 5, 2015
Messages
135
Loc.
BC Canda
Interesting! Definitely not grinding . more of a whirring sound i guess is the only way i can think to describe it. Glad to hear its somewhat normal! Tomorrow Im gonna pick up a new fuel filter, some timing tape, and blow out my fuel lines and see if we get anywhere with that. Ill check in hopefully tomorrow sometime!
 

gnpenning

Contributor
Bronco Slave
Joined
Dec 26, 2011
Messages
2,601
Loc.
I have more questions than answers.
Engine speed and ground speed need to be correct to shift proper as mentioned. Ground speed low with high rpms down shifting will be a issues. Notice your ground speed when you upshift at moderate throttle. To easily down shift you need to be going slower. Engine, tranny, and ground speed matching make for smooth shifts.

Sorry if you already know this.
 
OP
OP
Thatbroncokid

Thatbroncokid

Jr. Member
Joined
Mar 5, 2015
Messages
135
Loc.
BC Canda
Engine speed and ground speed need to be correct to shift proper as mentioned. Ground speed low with high rpms down shifting will be a issues. Notice your ground speed when you upshift at moderate throttle. To easily down shift you need to be going slower. Engine, tranny, and ground speed matching make for smooth shifts.

Sorry if you already know this.

This is a fantastic way of explaining it. Much appreciated!
 

Rustytruck

Bronco Guru
Joined
Feb 24, 2002
Messages
10,872
I'm pretty sure if you can't get the factory 2 barrel to run properly you will have severe problems making another set up run properly. You will not only have to buy parts but you will also have to buy some talent to make the parts work properly. Work to make your current parts to work properly. At one time this all worked and it can again. You can do this!
 
OP
OP
Thatbroncokid

Thatbroncokid

Jr. Member
Joined
Mar 5, 2015
Messages
135
Loc.
BC Canda
I'm pretty sure if you can't get the factory 2 barrel to run properly you will have severe problems making another set up run properly. You will not only have to buy parts but you will also have to buy some talent to make the parts work properly. Work to make your current parts to work properly. At one time this all worked and it can again. You can do this!

Thanks for the positivity!!
 
OP
OP
Thatbroncokid

Thatbroncokid

Jr. Member
Joined
Mar 5, 2015
Messages
135
Loc.
BC Canda
And a little update:

Nobody in my town sells timing tape, so I'm gonna have to order it from Amazon and wait a few days for it. Oh well. I'm sure something else will come up that needs fixing in the mean time!
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,651
Most of the auto parts stores that have one of those "Mr Gasket" wall displays in the old aisle will have one, but it's usually for a Chevy with a slightly smaller or larger diameter than what we need.
You can use them in a pinch, but I'd rather order the correct one like you're doing.

Paul
 
Top