• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Trouble taking off stock body mounts...Help!

Grandolla

New Member
Joined
May 10, 2006
Messages
2
I am trying to replace the body mounts but can't seem to be able to get the stock ones off. Any ideas? Thanks
 

purple72

Full Member
Joined
Dec 31, 2004
Messages
155
Loc.
Wilkinson,IN
Some of the bushings had steel sleaves in the center. Your best bet is to use either an air chisel or sawzall and just cut them out. I used an air chisel in order to eliminate all the burnt rubber smoke. Once you cut through them, they should just pop out. Good luck, cause' it's not much fun.
 

Mark

Contributor
Bronco Klutz
Joined
Aug 29, 2003
Messages
5,417
Loc.
NW Indiana
Ahhhhhhhhh....the joy of removing the original body mounts, how I envy you!
Definitely a sawzall application or an air chisel - cut them bastards apart.
Personally, with me, things don't start coming apart until I get good and pissed!
Have fun!
 

KJHill

Contributor
Sr. Member
Joined
May 26, 2004
Messages
456
Loc.
Central WA
I think I went through 3 blades for the sawzall doing mine. Messy, stinky & loud, but it worked out. My rule was to drink a beer before & after each mount was removed. ;D
 

trailpsycho

Bronco Guru
Joined
Dec 11, 2003
Messages
4,856
Try to get the sawzall blade between the rubber and frame side of the body mounts. IF you try cutting directly through the rubber mount itself, you will wear yourself and your blades out very quickly. I removed the bolts first, then attacked them with a little bit of weight off that particular side of the vehicle using a 2X4 under the rocker with a floorjack (and spacer 4X6)...I was able to slide the blades between the mount and rubber bushing fairly easily while cutting and the cut was reasonably quick. The metal sleeve thats seized inside the rubber isnt that thick and will go pretty quick if your not too much into the rubber. Good luck.

John
 

broncotime

Bronco Guru
Joined
Jun 30, 2003
Messages
1,188
Loc.
Grapevine, Texas
I used a chisel to split open the old rubber and peel it out then had at it with the sawsall! Oh, and the beer suggestion is a good one also. Don't forget to put some duct tape over the frame holes under the mounts behind the seats so you don't have to go fishing for parts that fall in there!
 

Cactus killer

Sponsor/Vendor
Sr. Member
Joined
Dec 22, 2005
Messages
736
The easy way is use a 9/16" drill bit and drill down through until you here a little pop, witch will break off the little fingers that hold the two parts together. It only takes about 10 seconds per mount and they will fall apart.
good luck
 

Cactus killer

Sponsor/Vendor
Sr. Member
Joined
Dec 22, 2005
Messages
736
The easy way is use a 9/16" drill bit and drill down through the hole until you here a little pop, witch will break off the little fingers that hold the two parts together. It only takes about 10 seconds per mount and they will fall apart.
good luck
 

Pa PITT

Contributor
Bronco Guru
Joined
Jul 15, 2005
Messages
11,300
Loc.
Stephenville TEXAS
I had this same trouble ...I have lots of tools so after the sawzall didnt seem too
help much .0.the air chisel sucked ..I think I got one out after about 4 hours of work so heres what I did ...guess I'll catch flack for this but I went a bougth 8 grade 8 bolts that were a little longer than the ones that came with the kit ..
and since my body mount were good I set the lift on top of the body mounts that were there and bolted it all up I guess I'VE got a 2 1/2 lift but it sure worked betterfor me ....
 

jkskier

Sr. Member
Joined
Jun 5, 2005
Messages
399
Loc.
Western Washington
I don't think I could have gotten the sawsall blade between the frame and the rubber mount. I had a crappy sawsall, so I had to cut wedges into the side of the rubber and then attack the center. Long, frustrating, messy process.

Don't forget a dremal with a cutoff wheel for the tabs on the sides of the rear middle mounts. You'll want those gone so you can get everything where it needs to go.
 
Top