• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Vent Window Repair

taylorB

Full Member
Joined
Apr 8, 2011
Messages
215
Loc.
Canton, GA
So ive been looking into why my vent windows wont stay open, they just flap. I figured that the spring and nut were missing or just needed tightening. I pull of the door pannel and come to find out the bolt, spring, and studd are rusted sollid!! :mad: I let it soak in WD-40 and try to tighten it up with smal breaker bar. I got nowhere, so its time to break out the air tools. But that only made things worse by breaking off the stud.... so here is my question, i know i can buy a new stud and everything but how do i take the window apart to get to the stud out??
 

trailpsycho

Bronco Guru
Joined
Dec 11, 2003
Messages
4,856
You have to remove the main glass from the window, then the window felt top and along the sill, next on the periphery of the door frame there are small screws. There is also one large screw just below the pivot of the vent window. With Ll this out of the way, angle the vent toward the latch of the door. It should angle enough to get it out. I dont recall that I had to remove any of the other glass tracks inside the door, but all that was already out when I removed the vents. Make sure the main door glass is out of the door, otherwise it may be easy to chip it on accident as the vent is angled out. I dont think there is enough clearance, even with the window bumper removed and the glass sitting on the bottom of the door.

Once the vent is out, you have to remove the glass from the frame. Ive read some people used a heat gun. I used a razor and was careful with screwdrivers. I did end up chipping one...but I had already bought new glass for the whole truck, soI didnt care much. With the glass out, you can drill the rivets for the pivot bolt--available after market. To put the glass back in the frame there is a special tape-like gasket-seal. Some people have used tthe new resins, but I called a local auto glass shop, they installed the glass into the frames for me for a good price...only a couple of bucks more than what they were going to charge for the tape-seal itself.

It is a total pain in the ass. As I was doing a frame off, it was one of the more tedious sub-projects of the whole build. I powder coated the frames flat black and replaced the rubber, which was of somewhat dissappointing quality.

Good luck!

John
 

Viperwolf1

Contributor
electron whisperer
Joined
Aug 23, 2007
Messages
24,451
It really sucks to replace the L-bolts and I hope I never have to do it again.
 

ericwilkison

Jr. Member
Joined
Jul 27, 2011
Messages
116
Loc.
Portland
I just had to do this on my drivers vent window. I called around but could not find any local glass shops that had the rubber glass seal. I ended up ordering 1/16" Everseal Glass Seal from here: http://www.b-dco.com/ecom/shop/item.aspx?itemid=294. It's good stuff. Installed very easily using motor oil as a lube (supposedly the oil soaks into the rubber and causes it to expand and lock into the frame). Trimed with a razor and looks like it came from the factory.
 

mudstud

Contributor
Bronco Bonehead
Joined
May 19, 2005
Messages
1,517
Loc.
Excel
I got the local glass shop to replace the glass and install the new L bolt for $25.
 

bluesbish

Full Member
Joined
Jan 30, 2011
Messages
278
Loc.
Upstate New York
I did both of mine. hardest part is getting glass out of metal frame without breaking it. I got one out and broke the other. jbg sold me a new piece of glass for about 30 bucks. I used black urethane window weld to glue them back in the frame. it is a fairly major process.
 
Top