• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Welding in floor pan patch

thegreatjustino

Contributor
Red Head Grease Monkey
Joined
Jan 23, 2002
Messages
16,291
Loc.
Stockton, CA
I have my driver floorpan pretty well trimmed and fitted. At the kick panel, there is a 1/4" or so gap. I did not trim this straight edge of the new pan at all. This edge lines up pretty darn well with the overlapping flap on the flat part of the floor, but the gap at the kick panel bugs me.

Am I supposed to T weld the patch to the kick panel? Lap weld a piece underneath? Don't weld there at all and use seam sealer to seal the gap? Some combination of the above?

This is my first time doing this. I'm comfortable with the spot welds at the floor support and rocker edge flap and the butt welds everywhere else. It's just this gap at the quarter panel I'm questioning.
 

Attachments

  • 20200502_184151.jpg
    20200502_184151.jpg
    112.3 KB · Views: 272
  • 20200502_185316.jpg
    20200502_185316.jpg
    119.2 KB · Views: 223
  • Gap.jpg
    Gap.jpg
    118.5 KB · Views: 235

1970 Palmer

Sr. Member
Joined
Mar 2, 2020
Messages
454
I just did some floor pans on my 1970 truck. I was able to leave the original pan lip about 1" from the kick panel. I cut the new pans slightly and they cover the original pan area. I massaged the edges to fit smoothly to the floor pan. I screwed them down about every three inches around the perimeter, and across the support. Then a final massaging to smooth the edges. Then I removed all the self taping screws, and used 3M panel bond to glue the pans to the floor. Replaced the screws and let it sit for 18 hours before I removed the screws. Removing the screws after 12 hours would have been easier. After the screws were removed, I placed a dab of Panel Bond on each screw hole and let it dry. I used the Tom's pans and was surprised how well they aligned with the original metal.

You might consider using a filler piece bent into a "L" that could be plug welded to the kick panel, and would give you the lip needed to support your new pan replacement.

John
 
OP
OP
thegreatjustino

thegreatjustino

Contributor
Red Head Grease Monkey
Joined
Jan 23, 2002
Messages
16,291
Loc.
Stockton, CA
The angled bracket from below isn't a bad idea. It would spot weld easily to the remnants of the side flap of the front floor pan.
 

1970 Palmer

Sr. Member
Joined
Mar 2, 2020
Messages
454
I think every rust repair is going to be a little different. The repair needs to take into consideration how much good metal is left to work with to mount the new panel.

I like using butt welds on flat skin patch repairs on quarter panels and fenders. It might take a little more time to metal finish both sides, but it will give a nicer end result after it's painted (note, lap welds show through on flat panels). IMO, on a floor pan repair a lap joint is just fine.

The skill is knowing when to use different kinds of body repairs.
 

AZ69EB

Sr. Member
Joined
Jun 8, 2006
Messages
680
How are you going to finish it, paint or bed liner? If this was my Bronco, this would be the deciding factor. If bed liner, the added “L” patch would be the easiest. If paint, a cleaner approach would be butt patch which would take more patience and time to make it look clean.

Good luck
 

elan

Sr. Member
Joined
May 27, 2015
Messages
541
Loc.
s
Home Depot sells 2 and 3 ft pieces of mild steel that is about 1/2" wide and about 1/32 in thickness. Grind your floor just wide enough for it to fit into the gap leaving the thickest part above the floor surface. Buff and clean all surfaces as though you were going to eat off of them. Focus your heat on the thick strip and let side heat and molten metal tie in the floor pan. Stitch weld in place and take your time, letting things cool down before welding to much to soon. Grind the thick insert and welds flat to your liking. Just a thought.
 
Top