• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

What knuckles do I have?

lars

Contributor
Been here awhile
Joined
Jun 29, 2001
Messages
3,334
Loc.
NorCal flatlands
Mine. Similar to Todd’s. 78-79 big Bronco knuckles, TRO with GM parts (I think Todd is using Ford parts). 4x4x2 steering box using one of the few remaining original parts of my Bronco, the OEM 1970 pitman arm. Stock track bar mount on the frame. Gary Yorston track bar mount on the right side inner knuckle. Angles look steep because when I took the photo the engine was out. Much flatter now with an actual running engine installed. Drag link and track bar are nearly the same length. Works pretty well.
 

Attachments

  • 2EBE8938-F569-475D-B96B-A30EBEC6A736.jpeg
    2EBE8938-F569-475D-B96B-A30EBEC6A736.jpeg
    274 KB · Views: 65
OP
OP
M

marcussly27

Jr. Member
Joined
May 6, 2015
Messages
142
Mine. Similar to Todd’s. 78-79 big Bronco knuckles, TRO with GM parts (I think Todd is using Ford parts). 4x4x2 steering box using one of the few remaining original parts of my Bronco, the OEM 1970 pitman arm. Stock track bar mount on the frame. Gary Yorston track bar mount on the right side inner knuckle. Angles look steep because when I took the photo the engine was out. Much flatter now with an actual running engine installed. Drag link and track bar are nearly the same length. Works pretty well.
So this set up, connections all the way in the corner compared to closer to center, works well for aggressive 4 x 4 mainly?
 

toddz69

Sponsor/Vendor
Bronco Guru
Joined
Nov 28, 2001
Messages
11,222
So this set up, connections all the way in the corner compared to closer to center, works well for aggressive 4 x 4 mainly?
It's the best of all worlds, frankly. Tie rod and drag link are moved up for clearance in the rocks. Drag link mounts close to the end of the tie rod to minimize the transverse loading that James mentions above. Trac bar and drag link are nearly the same length, angle delta between the two is not bad and their angles are good when the vehicle is at ride height. The roll center of the front suspension is moved up to preserve the stock roll moment couple. In my opinion, it doesn't get much better for an EB front end (without a drastic re-design) than what Lars is showing in his picture.

Oh, and the front end is dirty and dusty. That means Lars uses his Bronco like God, Henry Ford, and Bill Stroppe intended - frequently :).
Todd Z.
 
OP
OP
M

marcussly27

Jr. Member
Joined
May 6, 2015
Messages
142
It's the best of all worlds, frankly. Tie rod and drag link are moved up for clearance in the rocks. Drag link mounts close to the end of the tie rod to minimize the transverse loading that James mentions above. Trac bar and drag link are nearly the same length, angle delta between the two is not bad and their angles are good when the vehicle is at ride height. The roll center of the front suspension is moved up to preserve the stock roll moment couple. In my opinion, it doesn't get much better for an EB front end (without a drastic re-design) than what Lars is showing in his picture.

Oh, and the front end is dirty and dusty. That means Lars uses his Bronco like God, Henry Ford, and Bill Stroppe intended - frequently :).
Todd Z.
The best for an EB is what I’m aiming for! Does anyone sell a kit to achieve this set up? Looks like I’d have to get the trac bar Yorston mount and a heim tie rod/drag like the one from Tom’s. Based on my previous front end photos is there anything else to consider? The damper will still work although not sure it will be needed?

Thanks!
 
OP
OP
M

marcussly27

Jr. Member
Joined
May 6, 2015
Messages
142
In the meantime I’ll be removing the drip pitman to correct the trac/drag angles. This winter I’ll have a fun project to keep me from going crazy. Really appreciate all the help guys!
 

toddz69

Sponsor/Vendor
Bronco Guru
Joined
Nov 28, 2001
Messages
11,222
The best for an EB is what I’m aiming for! Does anyone sell a kit to achieve this set up? Looks like I’d have to get the trac bar Yorston mount and a heim tie rod/drag like the one from Tom’s. Based on my previous front end photos is there anything else to consider? The damper will still work although not sure it will be needed?

Thanks!
No one sells a kit for that setup that I'm aware of. It takes fabrication and I'm not a fabricator but I have friends that are and were/are very generous with their time to help me accomplish it on my truck.

I ditched my steering stabilizer back in about 1993 or 1994 and haven't felt the need to put it back on since then.

Todd Z.
 
OP
OP
M

marcussly27

Jr. Member
Joined
May 6, 2015
Messages
142

bigjhoov

nobody
Joined
Apr 10, 2005
Messages
3,583
Last edited:
OP
OP
M

marcussly27

Jr. Member
Joined
May 6, 2015
Messages
142
Since I have 44 knuckles will these f150 inserts work for TRO? I’d like to keep my existing tie rods and trac bar if possible. Find some inserts for TRO, install trac bar riser, done. I think everything should clear? Would prefer to do the least amount of drilling on the knuckles as possible.
 

bigjhoov

nobody
Joined
Apr 10, 2005
Messages
3,583
Since I have 44 knuckles will these f150 inserts work for TRO? I’d like to keep my existing tie rods and trac bar if possible. Find some inserts for TRO, install trac bar riser, done. I think everything should clear? Would prefer to do the least amount of drilling on the knuckles as possible.
Possibly, but it depends on what knuckles and flavor of tie rod ends you have.

The Bronco uses smaller factory tie rod ends than the f150 stuff I believe. It gets complicated because you are reverse tapering an existing taper. So, the tapered shims reduce you f150 size TRO taper down to fit the stock bronco tie rod taper.

If you have f150 knuckles and tie rod ends I believe the chevy 1-ton tapered shims will get you back to where you need to be. You really need to determine what you have before you start trying to change things.

Again, I think a stock pitman arm will remedy your current issues. Start small and work from there.
 
Top