• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Which circuit for fuel pump relay?

jeffncs

Contributor
Bronco Guru
Joined
May 4, 2004
Messages
1,898
Loc.
Raleigh, NC
I made the initial mistake of using the ignition stud for the trigger on my fuel pump relay but quickly realized the circuit is cold when cranking - which means the fuel pump is also cutting off.

Centech harness. Any suggestions for a circuit that’s hot when cranking and in “run” but goes cold when “off”

I know I can figure it out…, someone may save me from laying under my dash longer than needed….

Thanks!
 

jamesroney

Contributor
Bronco Guru
Joined
Sep 11, 2007
Messages
2,612
Loc.
Fremont, CA
Please clarify what an “ignition stud” means.

If it is the “Bat” terminal on the ignition coil, it is absolutely hot during crank. Otherwise the engine would never start.

If it is the “I” stud on the starter relay, it is also hot during crank, and then back-fed with about 8V thru the resistor wire.

The vast majority of carbureted applications do not energize the electric fuel pump during crank, because the float bowl has adequate capacity to run the engine when full.

The majority of SEFI systems control the fuel pump thru the ECU, and provide their own source.

The only other scenario that wants fuel pressure during crank ate those aftermarket TBI systems, and sometimes you need a time delay relay or a double pole ignition switch.

What are we working on?
 
OP
OP
jeffncs

jeffncs

Contributor
Bronco Guru
Joined
May 4, 2004
Messages
1,898
Loc.
Raleigh, NC
I was referring to the stud on the back of the ignition switch. It’s hot when the ignition is on but goes cold when cranking, shutting down the fuel pump off.

I may try the I-terminal. My carb wants more fuel….
 

Broncobowsher

Contributor
Total hack
Joined
Jun 4, 2002
Messages
37,110
No, don't do the I-terminal. It throws off the ballast resistor and results in reduced ignition power.

How does your fuel pump need more power on crank? is this carb or EFI? EFI is a whole hose of issues with power dropping out during crank, as in the computer is off. Carb the fuel bowls will hold enough fuel to start the engine and run for a long time (upwards of a minute in some cases) without any fuel pump. At most you may need a prime of the fuel bowls before starting. Are you running an oil pressure safety switch perhaps? That will block the fuel pump from working until you have oil pressure.

Something else is up. You just have not given us enough details to know what is really going on. I really want to know about this carb that needs more fuel on crank, if that is what it is.
 
OP
OP
jeffncs

jeffncs

Contributor
Bronco Guru
Joined
May 4, 2004
Messages
1,898
Loc.
Raleigh, NC
@Broncobowsher and @jamesroney

Carb is a 570 Holley
It’s a generic Amazon low pressure fuel pump
5.0/302 out of a 94 mustang

It’s a stock ignition box arrangement. I pulled the wire loom apart to retrace all wiring. Unfortunately (story of a busy life!) I don’t get the chance to actually trace any of the wires m. Maybe one night this week.

I have strong spark at the coil. It’s a used, unknown dizzy. I’m looking to replace it and to also ensure I have the right gear since it’s a roller engine.
 

jamesroney

Contributor
Bronco Guru
Joined
Sep 11, 2007
Messages
2,612
Loc.
Fremont, CA
@Broncobowsher and @jamesroney

Carb is a 570 Holley
It’s a generic Amazon low pressure fuel pump
5.0/302 out of a 94 mustang

It’s a stock ignition box arrangement. I pulled the wire loom apart to retrace all wiring. Unfortunately (story of a busy life!) I don’t get the chance to actually trace any of the wires m. Maybe one night this week.

I have strong spark at the coil. It’s a used, unknown dizzy. I’m looking to replace it and to also ensure I have the right gear since it’s a roller engine.
OK, the stud on the ignition switch is the "accessory" terminal. It will be hot in "run" and "acc." It will drop out in "start."

It means that your fuel pump will run in the accessory position too.

You should be able to turn the key "on" and hear the pump click until it pumps up...and the noise changes. Then you know the float bowl is full. Then you can crank the engine. The fuel pump will drop out, but it won't matter. As @Broncobowsher points out...it will run for a minute or more without the fuel pump running once the carb is full.

You can pick up the ignition circuit ahead of the ballast resistor and us it to trigger a relay, but do NOT power the fuel pump with the ignition circuit for all the reasons he posted above. The ballast resistor ignition bypass circuit is tricky, and when the ignition switch drops out...the I terminal on the starter relay tries to push voltage thru the ballast resistor back into the fuel pump. So you end up powering the fuel pump thru the backfeed circuit and it's generally a bad idea. You can pick up the ignition circuit at the voltage regulator too. But it turns out that it does EXACTLY the same thing.
 
OP
OP
jeffncs

jeffncs

Contributor
Bronco Guru
Joined
May 4, 2004
Messages
1,898
Loc.
Raleigh, NC
Thanks guys. I have a direct power source from the battery through the relay. I’m strictly looking for the best trigger circuit for the relay. I’ll check out those options you’ve offered and I’ll try some out. Thanks!
 

904Bronco

Contributor
Bronco Guru
Joined
Sep 28, 2004
Messages
6,720
Loc.
San Martin, CA
From the Centech harness directions, could you use one of these wires to trigger a relay (with Batt power) to operate your fuel pump?

Unfortunately, there is no reference if these wires have power in start and run???

EMISSIONS WIRING 8 ELECTRIC CHOKES
Power has been made available for OPTIONAL requirements such as electric chokes and electrical
switches used to control electrical emissions devices. These wires are labeled "CHOKE", "IDLE SOL" and
"DIST IYOD" and are HOT when the ignition is ON. These wires are available at the passenger side of the
engine compartment at a quick disconnect to allow for removal of these wires if not needed. Many
aftermarket carburetors and some original equipment carbs use an electric choke instead of heated air for
their operation. Connect the white "CHOKE" wire to the electric choke terminal. Make certain that the
remaining choke terminal, if provided. is grounded The electric choke may have only one terminal and
doesn't need an extra ground. Follow your Bronco manual for further information on emissions
requirements.
 

ntsqd

heratic car camper
Joined
Jan 30, 2005
Messages
5,970
Loc.
Upper SoKA
On all electric fuel pump conversions I use this oil pressure switch: https://www.summitracing.com/parts/crt-a68301 Note it has three terminals. One goes to the pump. one is battery power, and the third is 'Starting' mode. Pump wire goes to the control side of the fuel pump relay, power wire I run thru a fuse direct to the battery, the 'S' terminal gets a jumper wire from the 'I' terminal on the starter relay.

Wiring it this means that the fuel pump will run for a few seconds after a hot shut-down. It's been mine and other's experiences that this isn't a problem. When used together with a by-passing FPR I think that it's a desirable function as those cars seem to have less trouble starting again after a recent hot shut-down. Particularly when the carb has a small fuel bowl (Q-Jet, AFB).
 
Top