• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Wiring help

Stevenb

Contributor
New Member
Joined
Jun 24, 2007
Messages
39
Loc.
Spokane Valley, WA
Hello there. Merry Christmas everyone. I am putting in a Centech harness. I have the RJM efi harness already. My issues are with the two where they overlap. The alternator and battery area. I have the RJM all hooked up. Ran it for years. Now I’m swapping in a centric harness and that area has me stalled. Do I hook up the wires for the Centech as if I didn’t have an RJM harness? It seems like it doubles up on the alternator and battery wires. I may have other questions too but these have me questioning my already fragile sanity. Thank you for the help. I was trying to finish up tonight. Then I also noticed my tranny guy didn’t put my neutral safety switch back in when he rebuilt my tranny too. More fun. Thank you for the help.
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
Did your Centech harness come with the 3-wire adapter? Or was it the RF harness that was supposed to come with the adapter?
Been so long, I can’t remember!

Either way, there used to be a short adapter that connected to two together, and that was that.
The only crossover should be that, once that three wire connection is made, the RF harness takes over for the coolant temperature sensor, the oil pressure sensor, and the green wire to excite an internally regulated alternator.
Which you may not need, depending upon which alternator you’re using.

Sounds like you’re using a stock alternator with a separate regulator on the fender or firewall?
As Steve said, post up some pictures of your set up.
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
Sorry, I don’t remember how that used to go exactly. But like I said, it’s been awhile.

And just to bring it to the top for discussion, maybe now is the time to upgrade to a 3G alternator.😉
 

ntsqd

heratic car camper
Joined
Jan 30, 2005
Messages
5,970
Loc.
Upper SoKA
Now is always a good time to upgrade an original alternator. Everything that's been added to the truck likely has a power demand that the original alternator was not sized for. Anymore I want at least 100 amps from the alternator, more if the vehicle has unusual accessories.
 

904Bronco

Contributor
Bronco Guru
Joined
Sep 28, 2004
Messages
6,720
Loc.
San Martin, CA
Well my take without knowing how you have things hooked up currently is that the EFI harness would be left alone...

And you would use the Centech harness for charging and feeding power to the rest of the Bronco. Only exception I can think of is how your H20 temp and oil pressure sensors are wired, I can't remember if the RJM harness had a provision for that...
 

jamesroney

Contributor
Bronco Guru
Joined
Sep 11, 2007
Messages
2,607
Loc.
Fremont, CA
Well my take without knowing how you have things hooked up currently is that the EFI harness would be left alone...

And you would use the Centech harness for charging and feeding power to the rest of the Bronco. Only exception I can think of is how your H20 temp and oil pressure sensors are wired, I can't remember if the RJM harness had a provision for that...
RJM does indeed have the red/white and the white/red sender wires in the injector harness.
 

904Bronco

Contributor
Bronco Guru
Joined
Sep 28, 2004
Messages
6,720
Loc.
San Martin, CA
Thank you James...

I pulled up my RJM wiring harness instructions, pictures enclosed. (One of the 1st EFI harnesses I did back in the day)

As mentioned, the RJM harness has provisions for oil and water gauges, and there is a wire in the harness for A/C clutch activation.
You could run your Centech harness wires directly to the sensors or you could tie them into the harness connector where the RJM harness ties into the existing factory bronco harness at the firewall.
Same if you have A/C...

The RJM harness needs Ign power, which will need to come from the Centech harness. The directions reference getting power from the Ign switch RED/Green stripe wire on a factory Ford harness. They reference the pigtail wiring in the second picture.
I haven't installed a Centech harness in years... But I believe they have a number of wires on the passenger side of the engine bay (3 wires : Dark Blue, White and violet) in a 3-wire weather-pack connector that will have 12v ignition power. I see in their directions that there was a dark blue wire "Ign Pwr" that could be used for a 12v Ignition source. The Centech directions seem to imply that wires will have 12v in when the Ign switch is in the On position. Not sure if there is 12v power in start and run, or whether the RJM harness needs that (It is not stated in the RJM directions that it does.)

The directions also show an Alternator connection, it is just a field wire, it will have power when the ignition is energized. It is Not a Batt terminal wire. I would suggest that you just use the Centech harness to do the Alt circuit.

The RJM fuse/relays have a red 10g wire that needs to remain hooked to the Battery. It also has a 18g purple wire that needs to remain connected to the "S" of the starter relay.

I believe that about covers it. I hope my explanation isn't clear as Mud.

Doug.
 

Attachments

  • 20251222_113605[1].jpg
    20251222_113605[1].jpg
    275.6 KB · Views: 110
  • 20251222_114918[1].jpg
    20251222_114918[1].jpg
    189 KB · Views: 69
OP
OP
Stevenb

Stevenb

Contributor
New Member
Joined
Jun 24, 2007
Messages
39
Loc.
Spokane Valley, WA
Sorry. I should have asked better and clearer and added photos.

I made the connections at the firewall. Orange, blue and dark blue connected to the RJM with weatherpack connectors from the Centech. I followed the RJM color guide. It was water temp, oil pressure and ignition power.

I am running a 3 wire Chevy alternator at the moment. If I could swap to a 3-g on a v belt 351 Windsor easily enough I might do that.

My biggest question which I think I found an answer from DirtDonk from back in 2010 or 2013, was to only use the violet start wire going to the S terminal on the solenoid, and use the red to the battery with a fuse able link or mega fuse. It said pull the yellow and save for high voltage accessories. Pull the white I terminal that goes back to the weatherpack that Centech had wanted to go to the coil, but RJM does already.

So. I pulled the yellow tach feed wire back Green wire back, RJM already had a tach feed, yellow alternator back, and just left those two, the violet start and battery. I’ll hook the violet up along with the violet start from the RJM on the S terminal, and the other to the feed from the alternator on the solenoid post for battery power. I’d send photos but I’m at work now. When I get home I will.


It looks like nothing hooks to the I terminal now?

Also, they have two more violets going to the neutral safety switch on the tranny and two others for the back up lights. But the two for the lights are fed from the drivers side and the two violets are on the passenger side. Seems so odd to me. Any tricks with their hookups?

Thank you all for the help again. I will have to look into the 3-g alternator.
 
OP
OP
Stevenb

Stevenb

Contributor
New Member
Joined
Jun 24, 2007
Messages
39
Loc.
Spokane Valley, WA
I also have a question. So many. Sorry. In the passenger side there is the violet start wire that comes out near the battery with all of the other wires. But then I have a violet start and a violet ns start that aren’t loomed that come out by the firewall. Where do these little suckers go. I have the Centech illustration but it makes no sense to me for these wires. I wish I could add photos from my hone but that seems like it’s not an option. Thank you for the help.
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
Sorry, took a while to get back to this
The old Centech harnesses used to include two discreet purple wires.
One was a little shorter and was intended to go straight from the ignition switch directly to the “S” post of the starter relay. This one would be used in the case of manual transmission with no fancy interrupter switches in the middle.
The second, longer one (probably the one marked NS in your case) was meant to be run from the ignition switch to one side of your neutral safety switch on the side of the transmission.
Then the remaining length, after you cut it to length to fit the switch, is attached to the other side of the NSS and runs out to your S post of the starter relay.
They could have just made it one long wire, and called it a day. I think they did that in later kits.

But one is intended for use with a neutral safety switch or a clutch interlock switch if so desired.
The other would be used for a standard bronco with a manual transmission.
 
OP
OP
Stevenb

Stevenb

Contributor
New Member
Joined
Jun 24, 2007
Messages
39
Loc.
Spokane Valley, WA
Sorry, took a while to get back to this
The old Centech harnesses used to include two discreet purple wires.
One was a little shorter and was intended to go straight from the ignition switch directly to the “S” post of the starter relay. This one would be used in the case of manual transmission with no fancy interrupter switches in the middle.
The second, longer one (probably the one marked NS in your case) was meant to be run from the ignition switch to one side of your neutral safety switch on the side of the transmission.
Then the remaining length, after you cut it to length to fit the switch, is attached to the other side of the NSS and runs out to your S post of the starter relay.
They could have just made it one long wire, and called it a day. I think they did that in later kits.

But one is intended for use with a neutral safety switch or a clutch interlock switch if so desired.
The other would be used for a standard bronco with a manual transmission.
Thank you sir. I think I figured out how to add photos. We’ve been swamped with Christmas stuff that’s interrupting the bronco work! But last night was a Santa cruise on Lake Couer d’Alene, and that was the last thing until Christmas so I should be able to get back at it tonight. Thank you for taking holiday time to help me. I appreciate your wisdom and that you share it.
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
Happy to help. Now we’ll just have to wait to see if any of that was correct!🙄😉😁
 
OP
OP
Stevenb

Stevenb

Contributor
New Member
Joined
Jun 24, 2007
Messages
39
Loc.
Spokane Valley, WA
I also have a question. So many. Sorry. In the passenger side there is the violet start wire that comes out near the battery with all of the other wires. But then I have a violet start and a violet ns start that aren’t loomed that come out by the firewall. Where do these little suckers go. I have the Centech illustration but it makes no sense to me for these wires. I wish I could add photos from my hone but that seems like it’s not an option. Thank you for the help.
https://classicbroncos.com/forums/media/img_2264-jpeg.32811/

Link to photos of my wires.
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
You’re running a C4 Aut Trans, correct?
Where is the NSS Wiring?
Essentially, forget the purple/violet wire marked simply “start” or “starter relay/solenoid” or whatever it is. That’s straight from the key and used with a manual transmission.
You only use the one marked “NS start” or whatever the wording is.
It’s up to you, the end user/Installer, to follow the part of it that comes out of the driver side, firewall, cut it and splice it into 1/2 of the neutral safety switch on the transmission, and then splice the other half of the neutral safety switch into the remaining section of purple wire that should then be run over to the other side, where you will find it next to your other purple wire by the starter relay.

If I remember the last one I did, a 73 with an auto, I took the long half of the purple wire from the neutral safety switch, ran it back into the firewall where the driver side, across under the dash and out the other side in the harness. Rather than having it strung across the firewall or curved around the engine compartment.
But the final tucking and rolling is up to you.
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
A side note.
If you just wanna start the engine, for testing purposes, you can simply hook either of the violet wires to the starter relay S terminal right now and get the starter to crank.
The problem is, it can start in any gear and so you have to be extra careful to make sure it’s in neutral or park. If not, you could have a runaway freight train on your hands.
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
Are you at the stage that your battery is connected?
If so, rather than just testing for continuity on those wires, put the test probe on both wires, one at a time, and have someone turn the key.
See if you get a full 12 V on both of them.
 
Top