• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Yet another drivetrain problem

olsin6

Jr. Member
Joined
Feb 9, 2011
Messages
53
Loc.
Mesa
So I just recently installed shims in the rear end decreasing my pinion and yoke angle. Now I am thinking that my double cardan joint is the culprit. As I start to move forward (regardless of in gear or not), I get a knocking. My double cardan seems really loose. I get under the truck and I can move it side to side a good inch or two. I was thinking I could just take that joint out and take the driveshaft all the way up to the transfer case if the splines are long enough. Any advice or ideas?

Also my driveshaft I can get a half rotation in before it locks(this is off and just sitting there). Is this normal?
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,651
As I start to move forward (regardless of in gear or not), I get a knocking. My double cardan seems really loose. I get under the truck and I can move it side to side a good inch or two.

Pretty much any u-joint setup, double or single cardan type, should be free of any visible play whatsoever? So that one that moves like yours is toast. Whether it moves 2 inches, or 2-tenths of an inch, it's toast.
Actually, there IS some play, but you would normally not be able to feel it by hand. You'd have to measure it with dial-indicators and such.
Where exactly is it moving? With that much, it sounds like you might have not only bad joints, but the centering yoke and ball could be bad as well.


I was thinking I could just take that joint out and take the driveshaft all the way up to the transfer case if the splines are long enough. Any advice or ideas?

Do you mean take the special double-cardan setup out and use just a single joint at each end? If so, I wouldn't. You "can" of course, if you have a custom shaft built or yours lengthened, but by the time you do that, you might as well have paid for the new CV stuff and just fixed what you have.
Assuming it's still fixable that is. After all, that IS a bunch of movement.


Also my driveshaft I can get a half rotation in before it locks(this is off and just sitting there). Is this normal?

So what's moving? Your driveshaft's splines, or the pinion yoke on the rear end, or the yoke on the back of the transfer case, or all of the above?
And no, it's not normal. Same as my first answer. There should be virtually zero play in the joints, and just a tiny bit more in the splines. A little rotational play in the two end yokes is normal, but here again, it's just measured in thousandths of an inch in some cases. Even worn ones might be a 1/4" unless you've got a locker in the rear end.
Yours sounds a bit excessive. To say the least.

And just what led up to this? A new lift kit? Some other change? Or did it just start making a noise/vibration when you were just out driving it? Did it come on slowly, or all at once?

Paul
 
OP
OP
olsin6

olsin6

Jr. Member
Joined
Feb 9, 2011
Messages
53
Loc.
Mesa
Well I inherited the bronco when my uncle passed away. It has the James Duff 5.5" long travel "ultimate" lift I believe. I know nothing about axles or any of that so I have no clue I'd I have a Dana, one that's a locker etc. It's 4 wheel drive but front axle is not on.

I will have to see what exactly is moving, it is an aftermarket driveshaft already, just not sure how long it goes. I have new u-joints sitting right next to me but didn't want to put them in until I figured out the problem. This is not a DD, it was being made for a nice beach cruiser. The knocking was there when I got it. Although it has gotten better after I put te shims in. The double cardan just seemed a bit unnecessary to me, as a single cardan would do just fine. But you guys are the ones who know what your talking about. Its kinda hard to explain, but in person you can see it all.

I will try to take video and post it on an external website for you guys.
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,651
A video would be a good tool I think. They don't show everything well, but something like this sounds like it's right up that alley.
Sounds like you've got a great project. Sorry for the reason you got it, but the fact that he and his family left it to you is a great thing.

So it's pretty fixed up it sounds like. Tall lift and custom shafts already. Maybe the joints just wore out from a bad angle, and you fixed it with the shims? Maybe.

Smart to wait, and I didn't mean to come across so snooty with my first comment. The reason I said that I would not change to a single though, is that the doubles are WAY more forgiving of odd and acute angles. And with the lift, and the relatively short shaft of a Bronco, you're likely to have some hard to handle angles.
When you get the chance, if you can measure them, get some specifics on the relative angles of the rear pinion as it aims up towards the transfer case, and the angle of the transfer case's output yoke. See if they can be "matched" in relation to each other. That's the only way to get a single-cardan shaft to run without vibration.
I can't say for sure from here of course, until we see more of your truck, but it's typically much easier to make the double-cardan work.

Good luck. Will be waiting for your vid. And maybe some others with more experience with a 5.5" lift will chime in too.

Oh, and what other mods? Different transmission perhaps? Transfer case? Axles? Body lift? Steering linkage changes?
I know this is your first Bronco, so you might not know just from looking, but maybe you gathered that other things might have been done by your uncle.

Good luck.

Paul
 

trailpsycho

Bronco Guru
Joined
Dec 11, 2003
Messages
4,856
You definitely want to keep the CV. Have it rebuilt or rebuild it yourself; the parts are available. You dont want it to fail; been there and done that...by the time it drops and hits the ground at speed...you have to replace it...and your lucky if you dont seriously damage something else, tear something off or pole-vault.
 

broncnaz

Bronco Guru
Joined
May 22, 2003
Messages
24,342
Well the play in the rear end could either be due to a locker or the gears have to much back lash. Couldnt really see the t case end but one shot it looked like it had a lot of play. You probably need to tear it apart and see how worn stuff is if the pin on the end for the CV is fine then you should be good. Just replace all the joints.
Ujoints tend not to last long on short wheel base lifted vehicles especailly if the angles are jacked up. double cardon joints will help make the ujoints last longer even when the angles are off. But they still need the angles to be close.
 
OP
OP
olsin6

olsin6

Jr. Member
Joined
Feb 9, 2011
Messages
53
Loc.
Mesa
Well I got new u-joints sitting right next to me. But to be honest, if I was to pull the CV off, I wouldnt know what I was to be looking for. haha
 

rustbucket

Bronco Guru
Joined
Mar 22, 2004
Messages
1,579
I just want to mention that you can't really just take out the CV joint, or get a regular single cardan joint driveshaft, without doing some other work. If you decide to go this route, the pinion on the rear end needs to be on plane with the output yoke on the transfer case. You would have to cut your spring mounts and rotate your rear end to match.

On CV joints, the pinion on the rear end needs to be in line with the main tube of the driveshaft minus a degree or two. You want it to be perfectly in plane, but when you're driving and have load on the system, you make up that 1-2 degrees.

I agree with keeping the CV. It's a much better system. Take the driveshaft to a place to get it balanced. They can check the u-joints. If your truck was in gear, and your transfer case was in gear, then I might have a peak at those two units, as well. Seems like a bit much play.

Nice looking Bronco, by the way. Already has some nice goodies on it.
 
OP
OP
olsin6

olsin6

Jr. Member
Joined
Feb 9, 2011
Messages
53
Loc.
Mesa
Sounds good, so I'm going to go the CV route then. I appreciate all the help guys. I'll let you know what happens.

Thanks, the motor in it is immaculate and sounds like a throaty beast. It has over $14k invested into it and that's just adding up all the receipts he had saved.
 

thegreatjustino

Contributor
Red Head Grease Monkey
Joined
Jan 23, 2002
Messages
16,291
Loc.
Stockton, CA
OP
OP
olsin6

olsin6

Jr. Member
Joined
Feb 9, 2011
Messages
53
Loc.
Mesa
I actually got the kit from TBP, it came with the spicer clips, u-joints, and new CV. Awesome, so I guess I will replace that stuff and see how it goes.
 
OP
OP
olsin6

olsin6

Jr. Member
Joined
Feb 9, 2011
Messages
53
Loc.
Mesa
Top