• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Yukon 3rd Member

RonJones

Contributor
Full Member
Joined
Jun 30, 2001
Messages
347
A while back I bought a Yukon 3rd member with Grizzly locker. It comes without a yoke, but has the seal (but no oil slinger) installed. Do I just need to install a yoke and torque it to 200 ft-lbs, or do I need to disassemble the pinion Assyrian, remove the seal, set pinion preload, install new seal +/- oil slinger, and put the yoke back on?
 

Attachments

  • B03385C3-5CE8-45DF-97F5-6FA386C051B8.jpg
    B03385C3-5CE8-45DF-97F5-6FA386C051B8.jpg
    94.8 KB · Views: 67
OP
OP
R

RonJones

Contributor
Full Member
Joined
Jun 30, 2001
Messages
347
So at the very least I need to buy a pinion assy o-ring to figure that out.
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
I would think at the very least you should call Yukon and find out how they built it.
Seems to me that if they went to the trouble of selling a third-member without a yoke, but installed the seal fully, they don't expect you to have to pull it apart to do anything.

It's possible that you will have to, but it would sure be nice to simply install a yoke and be done. So I say it's worth the call.
Hopefully theyr'e open on Saturdays though, so you don't have to wait.

Any reason you remember you got it without the yoke installed?

Paul
 
OP
OP
R

RonJones

Contributor
Full Member
Joined
Jun 30, 2001
Messages
347
I bought it from another fellow who got it from JBG; apparently that’s how they sell ‘em.
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
Ok, thanks. I'm going to be ordering one up fairly soon and want to make sure mine's complete (with yoke) if it's offered that way.

Paul
 

bigjhoov

nobody
Joined
Apr 10, 2005
Messages
3,583
You could pull the pinion assembly and see what's between the bearings....
 

Yeller

Contributor
Bronco Guru
Joined
Mar 27, 2012
Messages
7,692
Loc.
Rogers County Oklahoma
Since it has no heat cycles the oring is reusable. Just pull it off the center support and inspect it, it's not so much about looking at it as "excercising" the rubber, it will be just fine.
 
OP
OP
R

RonJones

Contributor
Full Member
Joined
Jun 30, 2001
Messages
347
So, if it’s a solid spacer, just install yoke and torque to spec, correct? Otherwise, new crush washer and set up the preload?
 

Broncobowsher

Contributor
Total hack
Joined
Jun 4, 2002
Messages
37,111
Depends on if the crush sleeve has already been crushed. Or put in a spacer kit while you have it apart.
 
OP
OP
R

RonJones

Contributor
Full Member
Joined
Jun 30, 2001
Messages
347
Should I have to press the outer bearing in order to remove it? It’s been about 40 yrs since I’ve been into one of things, and I don’t recall having to do that.
 

Attachments

  • 18589FC0-4ADA-4AC4-8AD0-9F4CF9320445.jpg
    18589FC0-4ADA-4AC4-8AD0-9F4CF9320445.jpg
    124 KB · Views: 49
OP
OP
R

RonJones

Contributor
Full Member
Joined
Jun 30, 2001
Messages
347
So it is. The pinion assy does have a solid spacer/shims in it so I’m gonna reassemble and fab a yoke bar, then torque it to 200 ft-lbs and call it done.
 
OP
OP
R

RonJones

Contributor
Full Member
Joined
Jun 30, 2001
Messages
347
Here’s what the inside looks like.
 

Attachments

  • 80DDCE7F-DB52-4A58-89CC-5B524D60EBB3.jpg
    80DDCE7F-DB52-4A58-89CC-5B524D60EBB3.jpg
    83.7 KB · Views: 62

WILDHORSES

Sponsor/Vendor
Bronco Guru
Joined
Nov 7, 2003
Messages
2,253
Loc.
USA
That's a solid spacer. Don't forget to check the back lash and gear pattern. Never understood selling third member without a yoke.:cool:

Jim
 
Last edited:
Top