• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

ZF Transmission Question

Tedster100

Chairman of the Bored
Joined
Aug 25, 2010
Messages
1,762
Will a ZF from a F150 with a 4.9 in it bolt up to a 302 motor? It was listed as a 4.9 may be 4.6?
 
Last edited:

KyleQ

Bronco Guru
Joined
Apr 24, 2008
Messages
5,480
It should - the 4.9/5.0/ and 5.8 had the same bell...

Later Windsor V8 patternNote: this is commonly called the Ford Small-block V8 pattern, though it is used in some "big block"-sized V8's as well as some V6's and I6's.

200 I6 1978-1983 only, partial (4 of 6 bolts) pattern.
250 I6
255 V8
289 V8 - (made after August 3, 1964) - had 6 bolts holding bellhousing to block
302 Cleveland (Australia)
351 Cleveland V8 (not the 351 Cleveland M-block engine)
351 Boss
351 Cobra Jet
302 Windsor V8
351 Windsor V8
400 Cleveland M-block V8 aka 400FMX (certain 1973 casting numbers D1AE and D3AE, mated to the FMX transmission)
3.8/3.9/4.2L Canadian Essex 90° V6 (RWD only)
240 I6
300 I6
4.6L Modular V8 (first two casting runs, numbers F1AE and F2VE)
5.0L V8
5.8L V8
 

broncnaz

Bronco Guru
Joined
May 22, 2003
Messages
24,342
Its probably not a ZF thats behind that 300. ZF's were only put in F250's and to my knowledge only behind 351's 460's and diesels. Some savlage yard/parts sites may say a ZF was behind a 302 or a 300 but they usually just group stuff together because it can interchange. I personally havent seen a F150 that came from the factory with one. Doesnt mean it didnt happen but with the info out there in the ford circles its highly doubtful
 

KyleQ

Bronco Guru
Joined
Apr 24, 2008
Messages
5,480
Yeah - its pretty much 250 only territory, but car part lists a bunch a Zf5's from F150's... so who knows.
 

707Bronk

Sr. Member
Joined
Mar 18, 2012
Messages
590
When I swaped in a ZF, I only looked for the S5-42 and S5-47 models. I ended up with an S5-42 out of an early 90's F-250 4x4 with a SB bellhousing.

ZF makes a bunch of other Transmissions, but I think the S5-42 and S5-47's 4x4 versions are the typical ones for the Bronco swaps. There should be an ID tag to identify. I think from 87-95 was the S5-42 and from 96-97 had the S5-47. I also remember something about there being two different 1st gear ratios, and you definately want the lower 5.72 ratio.
 

ahansen_1985

Bronco Guru
Joined
Nov 2, 2008
Messages
1,245
Loc.
amity, oregon
This might help you Identify it by the case....
ImageUploadedByTapatalk1362076725.871948.jpg


1966,351w,m5od,205....3.5" lift, 2" body, 37/13/15 boggers
 

707Bronk

Sr. Member
Joined
Mar 18, 2012
Messages
590
I want a ZF so friggen bad...

They are cheap and abundant. I found one on craigslist for $250 (staming marks indicated it was recently rebuilt too). Junkyards should be filled with them.

My only concern with them is that they have an internal slave. Even though I think they are fairly heavy duty and reliable, if it ever goes bad, you must pull the tranny. I do like the feel and ease of the hydrollic clutch though!
 
OP
OP
Tedster100

Tedster100

Chairman of the Bored
Joined
Aug 25, 2010
Messages
1,762
Hey thanks! Even more good info! I can't find any ZF's in the wrecking yards, craigslist, anywhere around here! There's a place that has them rebuilt but it's $1,500 for one, too much for me. I'm still looking.. Thanks for all the info.
 

707Bronk

Sr. Member
Joined
Mar 18, 2012
Messages
590
Hey thanks! Even more good info! I can't find any ZF's in the wrecking yards, craigslist, anywhere around here! There's a place that has them rebuilt but it's $1,500 for one, too much for me. I'm still looking.. Thanks for all the info.

Wow! Maybe there are not as plentiful as I thought they were. They should be, given the number of 87-97 Ford F-250s that were sold. You guys out in Ohio either do not believe in Manual transmissions, or are you guys still using them as your daily drivers, or there is some guy out there selfishly hoarding them preparing for the apocalypse! haha

When I found mine, they seemed to be as plentiful as finding an NP435.

Thats a bummer though. Keep your eye out for anyone parting out an F-250, or perhaps buy one and part it out yourself.
 

broncnaz

Bronco Guru
Joined
May 22, 2003
Messages
24,342
Got to remember that manual transmissions are not as popular as they once were. Late 80's and early 90's I would almost say that over 80% of the trucks sold had autos. I think out of about 20 trucks in the junkyard of that era only 3 had manuals and one was a 2wd, one was diesel so that leaves only one small block ZF in my recent search. Far fewer manuals were sold and in todays market they are even harder to find. heck I dont even see very many F150's or big broncos of that era with manuals.
Also all the auto trucks now have higher towing capacity than the manuals it didnt used to be that way.

As for the different ratios Im pretty sure the differance is in the diesel versions. The gas versions have the lower first gear.
 

Dave

Contributor
Bronco Guru
Joined
Aug 25, 2006
Messages
2,264
Back when everyone was on the NV4500 craze the ZF was trashed on this and other forums as a POS. Mostly because they are aluminum and several were burnt up using gear lube instead of the recommended Dextron. I was ridiculed when I installed mine about 10 years ago. It's been a great trouble free tranny. I wouldn't discount the Mazda. They are a dime a dozen. I actually like the gear ratio better for a DD.
 

KyleQ

Bronco Guru
Joined
Apr 24, 2008
Messages
5,480
I've been looking for years around here and have not found one - I've never seen a manual F250 in my neck of the woods at a yard... Car-part comes up with a minimum of 450+ shipping...
 

AZ69EB

Sr. Member
Joined
Jun 8, 2006
Messages
680
They are loud with a lot of neutral roll over noise. Thye are a great transmission if you can get past that. I still need to put a loud system in my bronco!
 
OP
OP
Tedster100

Tedster100

Chairman of the Bored
Joined
Aug 25, 2010
Messages
1,762
Found a Mazda trans & transfer case nearby for $250. Think I'll pick it up & keep looking for a ZF. If nothing else I can get the NP205 bolted up and fabricate the cross members for them since they should be in the same location for the ZF. If I can't find a ZF right away I may just throw it in, 1st gear is much taller than my NP435 or the ZF but I could live with it for now if I can't locate a ZF.
 

707Bronk

Sr. Member
Joined
Mar 18, 2012
Messages
590
They are loud with a lot of neutral roll over noise. Thye are a great transmission if you can get past that. I still need to put a loud system in my bronco!

When I first put mine in it had a ton of neutral roll over. But, I also had a few other engine perforance problems as well.

I found that as I tuned the engine better, the roll over noise got less and less noticeable. Now the neutral roll over is almost gone and only noticeable when cold.
 

76Broncofromhell

Bronco Totalitarian
Joined
Jul 30, 2001
Messages
4,250
Loc.
Grass Valley, CA
Back when everyone was on the NV4500 craze the ZF was trashed on this and other forums as a POS. Mostly because they are aluminum and several were burnt up using gear lube instead of the recommended Dextron. I was ridiculed when I installed mine about 10 years ago. It's been a great trouble free tranny. I wouldn't discount the Mazda. They are a dime a dozen. I actually like the gear ratio better for a DD.

You speak the truth.


Other transmissions
M5OD can be good, as can an AX15 which also got a thrashing from YJ guys who couldn't tell an AX5 and AX15 or a BA10 from an AX15 and bought NV3550. For reference BA10s and AX5s look somewhat similar to an AX15s which is where the confusion started.

AX15s are still far easier to come by than the M5OD due to the huge amounts of Cherokees and YJs on the road and the internet rumors that they are weak. They've gone up in price though since their trough a few years ago.

ZF S5-42
I've had one in my Bronco for 10 years as well, and listened to many "old timers" (who are old guys who are completely full of it but sound knowledgeable) who demanded that it take 80W-90 instead of the recommended ATF. Fortunately I was smart and put ATF in it, and have experienced NO ISSUES in 10 years owning one.

I also have a ZF in my rock crawler for going on 4 years now with no issues. It's a great transmission.


Slave Cylinder
There is a lot of hype on them failing. I haven't had one fail yet. The biggest thing is to keep the factory hose away from heat as it is vinyl. If you replace the slave cylinder assembly and throwout when you swap in the transmission, you won't encounter any problems.


Finding a ZF
I pretty much glue myself to the Craigslist App when I'm taking a company-sponsored dump and type in ZF to see what comes up on the feed. I've found a few phenomenal items this way. So surf CL and Pirate as much as possible and you will find one.
 
OP
OP
Tedster100

Tedster100

Chairman of the Bored
Joined
Aug 25, 2010
Messages
1,762
Well, I found a ZF! At least I think I have. Searched an autoparts site and found three in a 90 mile area. Closest one is 7 miles away. You know, it used to be you called or went to a junk yard and asked if they had a part and they guy at the counter knew if they did and what row and condition it was in. Now, you call and unless you give them a specific year, make and model they can't tell you crap! The search turned up a ZF 4x4 box in a 93 F250, when I called and asked if they had any ZF transmissions the guy didn't even know what a ZF was. Then he insisted on a year, make and model. Foutunately, I had all the info from my search. He was floored when I told him it was for a 93 F250 4x4 and he searched and said I have one exactly for that year and model! Go figure says me! Going to look at it on Monday!
 
Top