• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

250 engine swap

Braddw25

Full Member
Joined
Jan 23, 2009
Messages
287
Loc.
Jersey Shore, PA
So I'm getting ready to swap a 250 inline into my Bronco instead of the 170 that's there. Has anyone here actually performed this swap? I'm particularly interested in what if anything you did to the stock motor mounts. I understand that the 250 is a little over an inch wider on the bottom end compared to the 170. I read on the FOrdsix site that this will cause the 250 to sit higher in the engine bay than a 170 or 200 would. Since the 250 is already taller than those blocks, I'm thinking this could cause me some problems. Also, would it cause problems with getting the rest of the driveline to line up right if the motor is sitting a bit higher than it should. Much of the info on the fordsix sight is based on Mavericks, Falcons, and Mustangs, so I'm not sure if the problems described there apply to the Bronco as well. That is why I would like to hear from someone who has actually done this swap.

I do know that I will have to either do a body lift or use some sort of hood scoop, and that the oil pan will need to be changed to rear sump. Any other issues that I should be aware of with this swap??

Thanks!
 

Explorer

Bronco Guru
Joined
Mar 2, 2008
Messages
4,390
Loc.
Raphine, Virginia
I started to do that swap, even bought an engine unseen that turned out to be a 240 big block. You have it covered pretty well. You will need the V8 bell housing as the starter mounts in the lower location instead of above the oil pan.
 
OP
OP
B

Braddw25

Full Member
Joined
Jan 23, 2009
Messages
287
Loc.
Jersey Shore, PA
That had to be a bummer on the 240. My 250 is sitting on blocks on my garage floor next to a 300. I knew the 300 was bigger, but when you see them side by side it's hard to believe just HOW much bigger the 300 is. I know it has been done, but I would not want to try to swap in one of those BB sixes. They are a great engine, but I think the mods required to get one to fit would be a bit beyond my abilities and patience.
 

Juntura

Jr. Member
Joined
Jan 17, 2007
Messages
90
I have a '66 bronco with a 170 and just recently purchased a 250 to swap in. There is a member from New Mexico (I think) who successfully did this a number of years ago. Pictures of his swap and his tbi conversion are on this site and bronco fix. I emailed him a while ago and he said that a 1" body lift, at the very least, is required. For motor mounts he said he just hogged out the holes on the stock engine cradles (Frame mounts) and then set the motor down with the mounts already bolted to the motor.

Other considerations- I have not started my swap yet as I have been buried at work (fortunately).

Oil pan- I am fortunate that my 250 came with a race style sheet metal oil pan that has lots of clearance. If you do not build a similar pan you will need to put the lower portion of the stock 170 pan on the 250 ring. The oil pans do not swap.

Clutch- based on looking at the setup for my clutch linkage it looks like the 250 will require some fabbing. Rather than fabing a mechanical clutch linkage I sourced an aluminum bellhousing from a late 80's Windsor truck that has mount for a slave cylinder.

Exhaust- If you want to do headers, which really help these motors, there were no options until just recently. Most bronco headers are for the 170/200 starter location. Classic Inlines is just no testing a set of headers that should work with a 250 in the Bronco. You may want to confirm this on the Ford6 site.

Cooling- My 250 is actually 269ci which is 58+% bigger than my 170. I am worried about cooling using the stock rad out here in the desert. Based on some real quick reads through vendor catalogs it looks like a 5.0 conversion radiator will bolt up and will have the inlet/outlet on the correct side. I need to research this further before spending $400+.

Carb- The most common way to mount a bigger carb on one of these log heads is with a bolt on stack style adapter. My measurements lead me to believe this set up will be too tall for just a 1" body lift. Classic Inlines sells a 2-brl adapter that you actually mill the head down before putting on a new 2-brl flange. I will be using this approach to keep everything as low as possible.

Sorry to ramble. I don't even know what I am going to do yet. I have a bronco with a running 170 in it, a recently rebuilt 200 sitting in the bed, and a hipo 250 short block with 1,000 miles on the garage floor. Too many options is not good for me!
 
OP
OP
B

Braddw25

Full Member
Joined
Jan 23, 2009
Messages
287
Loc.
Jersey Shore, PA
Not rambling at all Juntura. It's good to exchange ideas because two heads are better than one.

I am planning on cutting and flipping my oil pan from my 250 to convert it to rear sump. I was aware of the difference in oil pans.

I had not thought about the clutch linkage yet. I'm glad you brought that to my attention.

As for headers, I think that CLifford offers a header that they claim will fit any of the small sixes in a bronco.

Here is a link:

http://www.cliffordperformance.net/Merchant2/merchant.mvc?Screen=PROD&Store_Code=CP&Product_Code=53-2111&Category_Code=F200

I am planning on getting some kind of aftermarket radiator also. I doubt very much that the stock radiator would be enough to cool a built 250 which is what I'm planning on having.

I am going to get one of the alloy head/intakes from classic inlines, so I won't need to worry about having my log head machined. I will decide what carb to use when I figure out just how far I want to go with my motor performanc wise. I just want to make sure my Bronco can eat my Brothers new Jeep Wrangler for lunch. As long as my 250 can do that I'll be satisfied.
 

bmc69

Contributor
Bronco Guru
Joined
Jun 11, 2004
Messages
12,015
I did my 250 conversion a long time ago..and its no longer in my possesion (well teh truck is..I gave the engine and tranny/t-case away).

A few things I remember. I did not have any issue at all with the engine mounts. I did fuss with teh clutch mechanical linkage but not so much that I remember doing anything that took any real time.

I ran the forward sump pan..wth a 5.5" lift, I had plenty of clearance.

I ran the 250 bone stock and the stock 6-banger raddy always kept it cool just fine...and with no fan shroud to boot.

With no body lift, the Carter 1 bbl carb did not clear the hood. I installed a Duiff hood bubble 'scoop' and then fabbed up an aircleaner using two pieces of aluminum sheet that was offset to center the filter up in the hood as best I could.

The engine I used came out of a '70-something Grenada and so had the big bracket for A/C and PS. I never installed eiher..but they would have fit on there just fine.

V-8 bellhousing and all that..already noted.

I drove that combination as a daily driver for many years...bullet-proof engine.
 

Explorer

Bronco Guru
Joined
Mar 2, 2008
Messages
4,390
Loc.
Raphine, Virginia
rocklord has a new CI head and intake for sale. If you want one I would jump on it. CI is having production problems and mavereq waited over 4 months and finally scrapped his build. The Clifford intake may fit better on the 250, but it sucked on my 200. I had to dent the header and cut the starter bolt for it to fit my 200.
 

Juntura

Jr. Member
Joined
Jan 17, 2007
Messages
90
Explorer,

Thanks for the heads up regarding Rocklord. I pm'ed him. I think the Aluminum head is outside my budget, but we will see.

Brad,

If you are looking for performance out of your six make sure to call Clay Smith Cam's Techline and talk to George 714-523-0530. The guy who built my motor is good, real good (he built it for himself and I bought it when he moved on to another project) and he wouldn't stop talking about George. I called and spoke with George regarding the cam I need to make torque out of this stroked version; it didn't take George 10 seconds to come up with the custom grind that would work for me. Clay Smith is a bit more expensive, but I will pay for someone that knows their stuff.
 
OP
OP
B

Braddw25

Full Member
Joined
Jan 23, 2009
Messages
287
Loc.
Jersey Shore, PA
Thanks for all the suggestions gentlemen. Juntura, if you decide not to buy that intake and head, let me know. I am definetely interested.
 

bmbm

Contributor
Sr. Member
Joined
Jun 16, 2007
Messages
762
250 six in Bronco

I put a 250 in my 66 recently and this seems to be a complete list of what is involved. I still have the 170 radiator that has never needed anything in the 20+ years of my owning this Bronco. So far no overheating problems even in hot weather. Most likely this radiator will soon give out and I have considered the three core six radiator from WH. I did slot the mounts to lower the 250 and during the swap did the 1" body lift, plenty of room for stock carb and air cleaner.
Also with a 2.5" sl I have so far had no problems with the front sump pan with mostly street and light trail use. In the future the pan will be modified. Thinking about cutting the pan off the flange, turn it around and weld it back together.
No problems with driveline angles so lowering by slotting the mounts must have put it close to stock. I did the nv3550 conversion at the same time and that created a couple of extra things to do but was well worth it. Some fabrication was needed for the clutch linkage.
Also power steering conversion at same time and all seems to be working great.
 
OP
OP
B

Braddw25

Full Member
Joined
Jan 23, 2009
Messages
287
Loc.
Jersey Shore, PA
Thanks BmBM. Sounds like you are pretty pleased with your 250 install. I also just realized why I hadn't given any thought to clutch linkage before. I'm putting an M5R2 5 speed behind my 250 so I will be installing a hydraulic clutch.
 

mcdobson

Sr. Member
Joined
Jul 28, 2008
Messages
401
Loc.
Sacramento
What oil pump and pickup tube do you use if you modify the pan?
Juntura, you mention your engine was stroked, what combo of parts are used to stroke a 250?
 

bmbm

Contributor
Sr. Member
Joined
Jun 16, 2007
Messages
762
250 six in Bronco

mcdobson
As far as the oil pump and tube I am going to ask the guy who did this same swap on his Bronco. He has an old post on here somewhere concerning the GM fuel injection on his 250. I have his email address.
Bradw25
I am very pleased with this engine. This along with the 5 speed and power steering, front discs and other mods really changed the Bronco. What is an M5R2 out of? Does AA make an adapter?
 
OP
OP
B

Braddw25

Full Member
Joined
Jan 23, 2009
Messages
287
Loc.
Jersey Shore, PA
mcdobson
As far as the oil pump and tube I am going to ask the guy who did this same swap on his Bronco. He has an old post on here somewhere concerning the GM fuel injection on his 250. I have his email address.
Bradw25
I am very pleased with this engine. This along with the 5 speed and power steering, front discs and other mods really changed the Bronco. What is an M5R2 out of? Does AA make an adapter?

M5R2 5 speeds are found in F-150s and Broncos from around 89 to 96 or something like that. They are found behind 300 sixes and I believe 302s but not behind 351Ws or 460s from that time period. From what I have read they are identical to the bigger and sturdier ZF 5Speed as far as adapting goes so that an adaptor kit designed for the ZF will work with the M5R2. The M5R2 has a bad reputation that is largely underserved. For one thing, many people confuse them with another Mazda tranny, the M5R1 that came in rangers. The M5R1 is relatively weak and I would not consider using it in my Bronco. The other thing with teh M5R2 is that they have rubber plug seals installed in the case. These seals are prone to rotting and falling out which allows all the tranny fluid to leak out and ruins the tranny. THere are brass replacement plugs available and I can tell you that these trannies are plenty strong. I have two friends who have F-150s acquipped with the 300 six and M5R2 trannies. One has over 200K and the other has over 300K. They both had the stock rubber plugs replaced, and their trannies to this point have lasted as long as their 300 sixes. To me this says that the M5R2 is plenty strong enough for my little 250.
 

Juntura

Jr. Member
Joined
Jan 17, 2007
Messages
90
McDobson,

I have no idea all of the parts used to build my stroker motor. I do know the custom CP pistons were over $1,000 and the forged rods are from a turbo import car. Their are various stroker builds on the smallsix forum. The guy I bought my motor from goes by fast64ranchero and is a great guy to ask questions of.

Sorry I can't be more help regarding the swap- right now it is just a figment of my imagination.
 

bmbm

Contributor
Sr. Member
Joined
Jun 16, 2007
Messages
762
Braddw25
Thanks for the info on the M5R2. Recently a member talked about using a M50D with a 250 not sure how that turned out. The NV3550 seems hard to come by so other 5 speed alternatives are good to know about.
 
Top