bronco_daddy
Full Member
Anyone here using this system..'73 I just bought has it and I have been tweaking it along with some other things about it I want to mod..what has been you experience?
Biggest piece of crap I ever spent too much money on.........I sold it and put the carb back on. Seriously though, I had one on my old 302. Got the dual tank kit (additional pump and electric selector valve, wiring.......), closed loop kit and air/fuel ratio meter and installed an in line fuel pressure gauge to help with the tuning. My motor was fairly stock with only a little more compression and mild torque cam. Cold start was instantaneous and it ran really well once it was running (great mileage and smooth power) but, shut it off and...... good luck getting it started again! Once the motor was warmed up it was really tricky to start, do it wrong and it would flood. You had the hold the throttle just right and then, it would either flood or go into a high idle.......not ideal when you're trying to start it in gear (I have an NP 435) in a precarious, technical situation on the trail! I spent several hours (on more than one occasion) on the phone with Holley's tech dept. and they were no help at all. I finally got so fed up with it that I pulled it off and reinstalled the Edelbrock performer carb (that I hated but, carried in a plastic box....just in case) while out on the trail! I sold most of it to a guy that really wanted it for his Scout (I tried my best to talk him out of it) for $150! I saved the pumps, valve and adapter plate to use on the GM TBI conversion I plan to do (one of these days). Anyway, you asked for an opinion%) And no, it wasn't due to installer error as I'm extremely anal about how I do things. Hell, I was more knowledgable about tuning the thing than the rep I spoke with.Anyone here using this system..'73 I just bought has it and I have been tweaking it along with some other things about it I want to mod..what has been you experience?
Thanks for the support, Paul. In all fairness to Holley, after constantly screwing around with that thing, I read a small (very hard to spot) disclaimer in the installation manual, that said it was designed to be used on a totally stock, unmodified motor........my cam? still made plenty of vaccum so.......?:? ---------HansHey bronco_daddy. In case nobody's said it yet, welcome to CB! I see this isn't your first post, so you might already have gone through it, but what the heck.
Oatmeal has been a wealth of detailed technical knowledge, so with his direct experience, I'd say he's right on the money.
I know that's not what you wanted to hear of course, but I only know of a few people who have had their base Pro-Jections systems dialed in to the point they were happy about it. Doen't mean you can't get there, but just be ready for a lot of frustration. The concept is totally valid. It's just the implementation that seemed to work against us.
You might take a stab at the search function aboe to see what you come up with. Seems like there have been several discussions about just this subject recently.
Good luck! Hope yours is one of the ones that can be finely tuned.
Paul
Biggest piece of crap I ever spent too much money on.........I sold it and put the carb back on. Seriously though, I had one on my old 302. Got the dual tank kit (additional pump and electric selector valve, wiring.......), closed loop kit and air/fuel ratio meter and installed an in line fuel pressure gauge to help with the tuning. My motor was fairly stock with only a little more compression and mild torque cam. Cold start was instantaneous and it ran really well once it was running (great mileage and smooth power) but, shut it off and...... good luck getting it started again! Once the motor was warmed up it was really tricky to start, do it wrong and it would flood. You had the hold the throttle just right and then, it would either flood or go into a high idle.......not ideal when you're trying to start it in gear (I have an NP 435) in a precarious, technical situation on the trail! I spent several hours (on more than one occasion) on the phone with Holley's tech dept. and they were no help at all. I finally got so fed up with it that I pulled it off and reinstalled the Edelbrock performer carb (that I hated but, carried in a plastic box....just in case) while out on the trail! I sold most of it to a guy that really wanted it for his Scout (I tried my best to talk him out of it) for $150! I saved the pumps, valve and adapter plate to use on the GM TBI conversion I plan to do (one of these days). Anyway, you asked for an opinion%) And no, it wasn't due to installer error as I'm extremely anal about how I do things. Hell, I was more knowledgable about tuning the thing than the rep I spoke with.------------Hans
I think I would know what I bought, installed, removed and ultimately sold%) It was this unit here: http://www.pirate4x4.com/tech/projection/ 2DI, where 2=2barrel, D=digital, I=injection. No laptop programing, no idle air control motor. Bought the optional closed loop kit (oxygen sensor) to go with it and the air/fuel ratio meter (fed info from the oxygen sensor) to help with the tuning. Like I stated in my earlier post, I really liked the way it ran, but the hot start issue was totally unacceptable......isn't that one of the reasons one would want EFI? If you read the write up in the Pirate 4X4 link, it says "the engine is very easy to start up when its cold or has been parked for a long time"........what about hot start? So, please don't tell me what I DIDN'T have. ----------HansWell your comments state that you were NOT working with a 2DI system. but more then likely the old analog projection. Once again Holley projection is being lumped into a single program when it is not. There are several diffferent versions of the Projection system
The lowest and crappiest (and what a lot of people bought when it first came out and now gets a ton of bad feedback) is the old analog system. 5 knobs on the box, no O2 sensor (but kit availible)
Then there was the "D" or digital. Can't remember if it had O2 or not. Tuned about the same way but with plug in knobs.
Then through the late 90's the high end, the "DI" or Digital Interactive. This one takes a laptop to get dialed in. Rev limiter, O2 switching voltage, a bunch of stuff is programable. Still a pain to do, but can be done far better then the old analog systems. O2 sensor was standard for this.
I have not played with the latest and greatest Commander 950 system the Holley makes.
So just to be fair, when you have questions about Holley fuel injection and are looking at feedback, make sure the feedback you get actually matches the model you are playing with.
--end rant on generalizing Holley ProJection---
So you are working on an existing already installed system. Did you get the software disks with the truck? without those you are not doing anything. You really should have the manual as well. The copies I had just went with the last Bronco I sold so I don't have mine anymore either.
If it is an older DI system with an older ROM, there are some firmware issues that anything newer then Windows 95 (pre SE version) won't run. I updated my old laptop and was locked out of the fuel injection for several years. Found an old laptop that had been hiding in a closet for years that had an old enough operating system that I could get into the fuel injection again. After talking with Holley about it they have an updated ROM that could have fixed mine so I could use a newer laptop. I never bothered to update. But if you have the disks, and the cable and can't get the two to talk, that may be your issue.
With it set up right it ran good. I was running a 351W that was no slouch. Had small cam and Trickflow heads on it. IT was EFI so it always started and ran the same regardless of angle. It controlled idle so it idled the same. Lug it, and it would add a little idle to keep it going. did pretty much anything any other factory EFI could do except that I could change the settings. Want 50 more RPM of idle, few keystrokes and it is done. Lean on the top end, add more fuel just to the top end.
I ran the DI system for 10 years. And I got it used. I would not have left it there that long if it was that bad.
I also knew people who had the old analog system, mounted to the bottom of the dash so they could turn the knobs as they drove down the road to get them to run right. I don't think any of them still have that system anymore.
Naw no problem, the wound has healed and only a small scar as a reminder remains;D You seem to really know what you're doing. Mine was the opposite, it ran pretty good when cold but, was dumping too much fuel during a hot start. I dunno maybe it just didn't like the cam I had but, the number of people I spoke with that had issues........ well, we could have started a support groupSo, sorry I touched a nerve with you and uncovered some old wound
Yeah, I replaced the temp sensor, adjusted the fuel pressure regulator (there's an adjustment screw at the throttle body return port) set the TPS voltage per Holley's instructions, the mixture was also set to the proper stoic ratio via the control pots on the under dash mounted computer.......that was tricky as the meter is hooked to the oxygen sensor but, the mixture needs to be set with the oxygen sensor out of the loop (open loop as in not feeding data back to the computer) so, I had to rig a toggle switch that would interupt feedback to the computer but, would still supply power to the meter, no vacuum leaks etc, I bought it through Summit and they even sent me a replacement computer, thinking that, that might have been the problem (Summit, by the way, is great to deal with!)......I mean, I loved the way it ran but, the hot start issue was extremely aggravating. I once got over 17mpg on a trip home from the Rubicon! I bet if Holley would have designed it with some sort of idle air control (like a stock GM TBI system) it would have been alot better.--------HansI'm wondering, not knowing diddly about the projection stuff, that if your having hot start problems, I would look to a temp sensor being bad, is there a temp sensor included in that thing?
Lastly, as always, are you sure you don't have a intake vacuum leak? Do you have any idea what you fuel ratio is while it is running?






