• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Transfer Case vent options

OP
OP
Fitz24

Fitz24

Bronco Guru
Joined
Jul 4, 2007
Messages
1,299
I just bought a single 1/4" NPT tap at Lowes in the tool section. You don't need an entire pipe tap/die set. You most likely won't use it but a couple of times. Make sure you buy some teflon tape to seal the threads also. Just wrap 2 or 3 layers.
 

zerostar2410

Sr. Member
Joined
May 19, 2009
Messages
612
just found one at my local parts store.

I took the mushroom cap off and found this:
SSPX0223.jpg


Can someone please walk me through the steps? what do i do next? am i just supposed to thread through this?
 
Last edited:

Steve83

Bronco Guru
Joined
Jul 16, 2003
Messages
9,360
Loc.
Memphis, TN, USA, Earth, Milky Way
Hook something under it & pry it up. Or lock ViseGrips onto the edge & pull it out. If it breaks off below the casting, drill it out or drive it through, and then clean the inside of the t-case.
 
OP
OP
Fitz24

Fitz24

Bronco Guru
Joined
Jul 4, 2007
Messages
1,299
Grab it with pliers or vise grips and wiggle it back and forth until it pulls up out of the case. Once out, the hole will be about 1/2" in diameter. It is just about the right size for the 1/4" NPT tap so you don't need to drill. If you do have to drill some out, make sure you turn your case upside down to keep shavings from getting inside the case. The hole is already slightly larger than it needs to be for the tap so make sure not to drill it out to a larger size.

Since you have the tail housing mounted to the main case you don't want to let any shaving from tapping get down inside the housing. Turn you case upside down so the hole faces the ground. Put a lot of grease on the tap and begin to thread into the hole. Make sure you thread a little then pull the tap out and test fit a 1/4" male fitting. You want the fitting to go in as far as possible BUT it must tighten up before you run out of thread on the fitting. If you run the tap to far in, you will end up with a loose fit and the fitting will not tighten up properly. Make sure to clean the tap and use new grease each time you pull it out for a test fit.

Once you get the hole threaded to where you feel you have enough thread to tighten up good and before you turn the case back over, shine a light in the hole and look for shavings. There should not be any but you need to make sure. Once you verify there are no shavings inside the case, turn it back over.

You can then put teflon tape on the threads of the fitting and install. When putting the tape on the fitting wrap it in the same direction as if you were threading a nut onto the fitting. That prevents the tape from unwrapping as you thread the fitting into the hole. Snug up good but do not over tighten.

Good luck. I hope this helps.
 

zerostar2410

Sr. Member
Joined
May 19, 2009
Messages
612
very descriptive but, what am i supposed to be pulling out/off? the entire outer circular piece? or just the inner piece with the small hole?
 

zerostar2410

Sr. Member
Joined
May 19, 2009
Messages
612
what type of elbows did you guys use? All of the ones i tried wouldnt screw in because there isnt enough room to screw it in. what type of material is your fitting and pictures would help. thanks.
 
OP
OP
Fitz24

Fitz24

Bronco Guru
Joined
Jul 4, 2007
Messages
1,299
I used a 1" brass nipple with a brass 90 degree elbow. Then screwed a barbed fitting into that. I left it pointed toward but a little rear of the speedo cable. That let me run the hose around behind the case to the frame and then up under the hood along the wiring harness and ARB lines. Just tie wrapped them all together.
 

broncoroper

New Member
Joined
Aug 31, 2009
Messages
4
off road venting

If you ever plan on driving through even relatively shallow water, you may want to extend the breathers on all gear cases (diffs, t-case, tranny) up higher to avoid the possibility of water getting into those area.

Not any more to modifying the transfer case breather than what's been stated in this thread already.
  1. Remove the stock breather
  2. Tap the hole for a NPT fitting
  3. Connect that fitting to a breather higher up in the Bronco.
I just bought a couple cheap breathers at Autozone. I never had one connected to the Dana44, and didn't extend the one on my NV4500 when I installed it. I do have the transfer case and 9" extended up.

you can check out our web site at lovelakeent.com we may have some stuff that is helpful to you
 

zerostar2410

Sr. Member
Joined
May 19, 2009
Messages
612
ok, i got a problem. Just finished installing new vent breather. I took off the output shaft(?) that the breather vent portion is on.

After assembling everything, I noticed i was unable move the shift rails from outside the case like i used to prior to dismantle. is this common? was i supposed to be able to shift the case from the outside with the shift rails? am i supposed to be able to shift them now?

I dont want to put it back on the bronco and find out it wont shift through the gears.
 

Viperwolf1

Contributor
electron whisperer
Joined
Aug 23, 2007
Messages
24,451
ok, i got a problem. Just finished installing new vent breather. I took off the output shaft(?) that the breather vent portion is on.

After assembling everything, I noticed i was unable move the shift rails from outside the case like i used to prior to dismantle. is this common? was i supposed to be able to shift the case from the outside with the shift rails? am i supposed to be able to shift them now?

I dont want to put it back on the bronco and find out it wont shift through the gears.

Did the 13 roller bearings drop out of the end of the output shaft? They can easily jam things up.
 

zerostar2410

Sr. Member
Joined
May 19, 2009
Messages
612
No, the rear output housing & vent have nothing to do with the shift rails. Did you bend the caps?


I figured it had nothing to do with it. Bend what caps? Im pretty sure i didnt bend anything.




Did the 13 roller bearings drop out of the end of the output shaft? They can easily jam things up.


Those 13 bearings fell out a long time ago, but i recovered them. I also dont see anything jamming the rails down below. The rails move somewhat, but not enough to move the forks in order to move the ring gears.I cant move the rails by hand like i used to be able too.
 

Viperwolf1

Contributor
electron whisperer
Joined
Aug 23, 2007
Messages
24,451
Those 13 bearings fell out a long time ago, but i recovered them. I also dont see anything jamming the rails down below. The rails move somewhat, but not enough to move the forks in order to move the ring gears.I cant move the rails by hand like i used to be able too.

Ok I re-read your post. If you're trying to shift it without the shifter it ain't gonna happen. If you remove the detent plugs/springs/balls you can do it.
 

zerostar2410

Sr. Member
Joined
May 19, 2009
Messages
612
Ok I re-read your post. If you're trying to shift it without the shifter it ain't gonna happen. If you remove the detent plugs/springs/balls you can do it.

Yes, i am trying to shift it without the shifter. I was able to shift it before without the shifter. I would just grab the shift linkage and pull the individual rail. Now i cannot do that. if i attach my twin stick, would i be able to shift it? i just want to make sure it shifts before i install.


Do you have images enabled? They're labelled in that diagram as "caps". ;) ;D

Oh, haha... Didnt even touch the caps. They're not bent.
 

Viperwolf1

Contributor
electron whisperer
Joined
Aug 23, 2007
Messages
24,451
Yes, i am trying to shift it without the shifter. I was able to shift it before without the shifter. I would just grab the shift linkage and pull the individual rail. Now i cannot do that. if i attach my twin stick, would i be able to shift it? i just want to make sure it shifts before i install.

Shifter or long screwdriver will do it.
 

Viperwolf1

Contributor
electron whisperer
Joined
Aug 23, 2007
Messages
24,451
I tried a long screwdriver and had no luck. Ill try to install the sticks tomorrow and see what happens.

any other ideas just in case the forks dont move?

Loosen or remove the detent plugs and try it. If it works with the plugs removed it's ok inside. If you shimmed the springs you might have shimmed too much.
 

zerostar2410

Sr. Member
Joined
May 19, 2009
Messages
612
Loosen or remove the detent plugs and try it. If it works with the plugs removed it's ok inside. If you shimmed the springs you might have shimmed too much.

I didn't touch anything other than loosening the 5 bolts to take off the output shaft in order to tap the breather vent. but will try to mess with the detent plugs.
 
Top