• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

eliminating the 3 speed column shifter

Gas Pig

Bronco Guru
Joined
Oct 19, 2005
Messages
2,778
I'm eliminating the stock 3 speed sifter and putting a smooth collar back on the column. Can I also remove the shift tube without effecting the steering shaft operation. It appears that the steering wheel nut does not preload against the shift tube and/or collar but the lower steering shaft bearing. So, there would be no effect if the shift tube is in or out the steering column. Is this true?

Thanks Jeff
 

garberz

Bronco Influencer
Joined
Jun 24, 2007
Messages
6,864
Loc.
Conejo Valley, Ca.
I removed the shifter tube and went with the smooth collar. I think the 3 speed collar and shifter tube are all one piece. Take it out and you'll be fine.
Mark
 

av bronco

Bronco Guru
Joined
Mar 3, 2008
Messages
1,742
Loc.
Palmdale CA
I have a auto and did the smooth collar from toms, the billet one you have to drill mounting holes for it but when I pulled the shift shaft out no problems.
 

casadejohnson

Bronco Alchemist
Joined
Jan 21, 2005
Messages
3,587
A couple quick notes on this.

First, go ahead and yank the shift tube. After you do, cover the hole in the column where the shift leavers come out ( Under the hood ). A lot of air makes its way through the column and into the cab if you don't.

Second, before you go ordering a smooth collar from one of the vendors you can check your local pick and pull yard. Forget looking for Mustangs to find it, head to the 70's Ford trucks and find one with a standard transmission. I grab a couple every time I go to the junkyard. I pay a couple bucks for them and Ebay them for $30-40
 
OP
OP
Gas Pig

Gas Pig

Bronco Guru
Joined
Oct 19, 2005
Messages
2,778
Hey guys thanks! I didn't think removing the tube shift would effect the steering because they work independent from each other. If they weren't independent you would shift gears while turning. lol

I had planed on welding a small cover plate were the shift levers comes out for a cleaner finished look. Also casadejonson makes a good point about the air moving through an empty tube too.

I'll hit the local boneyard to see if any smooth collars that I could grab.

Thanks again to all, Jeff
 

casadejohnson

Bronco Alchemist
Joined
Jan 21, 2005
Messages
3,587
Jeff,

I was out at the bone yard this morning and grabbed another shift collar. I gave $5 for it. If you want it, you can have it for what I paid and the cost of shipping. If not, no worries, I'll ebay it.
 
OP
OP
Gas Pig

Gas Pig

Bronco Guru
Joined
Oct 19, 2005
Messages
2,778
Jeff,

I was out at the bone yard this morning and grabbed another shift collar. I gave $5 for it. If you want it, you can have it for what I paid and the cost of shipping. If not, no worries, I'll ebay it.

Thanks I might take you up on the offer. Today I ground off the shift handle part of the stock shift collar. I'm going to fill hole with Alumaloy. If it turns out well I'm good if not I'll take you up on yours. Please give me a day or two to let know before ebay it.

Thanks again, Jeff
 

casadejohnson

Bronco Alchemist
Joined
Jan 21, 2005
Messages
3,587
Thanks I might take you up on the offer. Today I ground off the shift handle part of the stock shift collar. I'm going to fill hole with Alumaloy. If it turns out well I'm good if not I'll take you up on yours. Please give me a day or two to let know before ebay it.

Thanks again, Jeff

No problem, take your time. I just thought about it while I was there so I grabbed it. If you don't need it, it will go into my "Ebay it" box till I get around to doing it. While I was in the yard, I picked myself up a 79 tilt column for $30. It kinda makes the $5 for the shift collar seem high.%)
 
OP
OP
Gas Pig

Gas Pig

Bronco Guru
Joined
Oct 19, 2005
Messages
2,778
No problem, take your time. I just thought about it while I was there so I grabbed it. If you don't need it, it will go into my "Ebay it" box till I get around to doing it. While I was in the yard, I picked myself up a 79 tilt column for $30. It kinda makes the $5 for the shift collar seem high.%)

Thanks and I'll let you know in a few days for sure. I need to keep moving on this project. Anyways here is what I did with the shift lever hole/slot to fill it in so air doesn't pass through to the cab.

As You can see I had a scrap column that I cut a section out of. I figured that the scrap would be prefect because the wall thickness and curvature of the steel is exactly the same. All I had to do is make a piece that was a close fit to the hole and weld it in. I clamped caddy corner to insure proper fit. Weld it up, then grind it smooth again. I'll 2K prime and sand smooth to fill any pits left from rust (from under the rubber firewall column seal) or my work blocking off the hole.
 

Attachments

  • DSCN0010.jpg
    DSCN0010.jpg
    67.1 KB · Views: 141
  • DSCN0011.jpg
    DSCN0011.jpg
    43.7 KB · Views: 89
  • DSCN0012.jpg
    DSCN0012.jpg
    61.4 KB · Views: 122
  • DSCN0013.jpg
    DSCN0013.jpg
    42.7 KB · Views: 111

pcf_mark

Bronco Guru
Joined
Jun 11, 2010
Messages
3,697
Nice work! I am stealing the column idea from a Ford truck from this thread when I am at a yard next...
 

Lunar-tic

Sr. Member
Joined
Sep 28, 2009
Messages
629
Loc.
Brentsville
Jeff, do you have to remove the column to get the shift tube and levers out? I just converted from a 3 speed to a C4 and I want to do the same thing.

Thanks
 
OP
OP
Gas Pig

Gas Pig

Bronco Guru
Joined
Oct 19, 2005
Messages
2,778
Nice work! I am stealing the column idea from a Ford truck from this thread when I am at a yard next...


Hey Mark, thanks it wasn't really that hard. Hopefully I'll have some finished pics in a day or two, all painted up.
 
OP
OP
Gas Pig

Gas Pig

Bronco Guru
Joined
Oct 19, 2005
Messages
2,778
Jeff, do you have to remove the column to get the shift tube and levers out? I just converted from a 3 speed to a C4 and I want to do the same thing.

Thanks

Hey William, I did remove the whole column from the truck. I wanted to fill the hole and then paint so it I had to pull the column.

But to answer your question I don't see a reason why you couldn't just pull the 3 speed shift tube & levers to swap it out for a auto tube and lever. But I have never done that before myself. Hopefully someone who has will post to this thread!

The only hang up would be for the blinker wires which could be snaked back through the column even on the truck but a bit harder then if it were on a bench.
 
OP
OP
Gas Pig

Gas Pig

Bronco Guru
Joined
Oct 19, 2005
Messages
2,778
Here are pics of the column painted with the 3 speed shift lever hole plated over. Also I have installed the new after market wheel which I happen to really like. I got this one off ebay for $112 shipped and it came with everything I needed.:)

Please excuse the finger prints over shiny new wheel.
 

Attachments

  • DSCN4965.jpg
    DSCN4965.jpg
    50.1 KB · Views: 97
  • DSCN4964.jpg
    DSCN4964.jpg
    55.5 KB · Views: 97
  • DSCN4957.jpg
    DSCN4957.jpg
    121.7 KB · Views: 112
  • DSCN4956.jpg
    DSCN4956.jpg
    106.9 KB · Views: 105
  • DSCN4962.jpg
    DSCN4962.jpg
    52.3 KB · Views: 91
  • DSCN4963.jpg
    DSCN4963.jpg
    55.3 KB · Views: 101
Top