• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

LOWERING my Bronco

OP
OP
greatguy57078

greatguy57078

Contributor
Bronco Guru
Joined
Jul 15, 2006
Messages
3,430
Here are a few pics to show what I am aiming for. I would refer to the person that I "borrowed" the pics from (bax maybe?), but I am not sure who it was other than I remember it was his dad's rig....maybe?
 

Attachments

  • floor mod 1.JPG
    floor mod 1.JPG
    168.5 KB · Views: 133
  • floor mod 5.JPG
    floor mod 5.JPG
    58.9 KB · Views: 126

77bronco_ed

Bronco Guru
Joined
Jul 3, 2004
Messages
1,793
Get anything done over the weekend?

Checked the calander, Hudsonville swap meet and Broncorama are right around the corner
warm weather is near ;)
 

behemoth

Bronco Guru
Joined
Jul 2, 2003
Messages
1,736
I built some gap fillers for the doors, found some rattle can paint that comes kindof close and installed them. Working on building a cheap toneau cover for the back bed, just plywood and some kind of covering for the plywood.

Not much other than the eb tach showed up yesterday so that will go in sometime this week.
 
OP
OP
greatguy57078

greatguy57078

Contributor
Bronco Guru
Joined
Jul 15, 2006
Messages
3,430
What tach did you get? The one that WH started selling that match the speedo? They have a place her locally that does bed covers for trucks all over the country. Very well made and function well. Truxedo

http://www.truxedo.com/
 

Attachments

  • NEW TACH.jpg
    NEW TACH.jpg
    51.3 KB · Views: 87

behemoth

Bronco Guru
Joined
Jul 2, 2003
Messages
1,736
Thats the tach, mine is mounted lower left side. Since I shortened my column on this side by 4" its a little tight. Those covers are nice, but I am going low budget. The bed on mine does not appear to be square anymore so I am glad I did not spend a lot on it.
 
OP
OP
greatguy57078

greatguy57078

Contributor
Bronco Guru
Joined
Jul 15, 2006
Messages
3,430
Thats the tach, mine is mounted lower left side. Since I shortened my column on this side by 4" its a little tight. Those covers are nice, but I am going low budget. The bed on mine does not appear to be square anymore so I am glad I did not spend a lot on it.

Snap a pic of that tach in your truck when you have time. I think lower left is the only way to mount it, unles you have room straight up. Either way...I want one! :eek:
 

behemoth

Bronco Guru
Joined
Jul 2, 2003
Messages
1,736
Here it is just placed I have to wire it now and adjust it. I really would like one of these without the black face to match the cluster.
 

Attachments

  • Photo0309.jpg
    Photo0309.jpg
    58.3 KB · Views: 142
  • Photo0308.jpg
    Photo0308.jpg
    62.8 KB · Views: 101
  • Photo0311.jpg
    Photo0311.jpg
    73.2 KB · Views: 101

77bronco_ed

Bronco Guru
Joined
Jul 3, 2004
Messages
1,793
Mass buy on the tach right now.... Placed an order.

Marty did you/will you need to modify the firewall with the 4.6?
 

behemoth

Bronco Guru
Joined
Jul 2, 2003
Messages
1,736
Here are some pics of its current and close to final state. I think when the time comes for paint I will paint it the same brown color again.

I will be dropping the rear lower to achieve this ride height, it will require some bed floor cutting as well as some rear inner fenders.
 

Attachments

  • DSCN2939 (Medium).jpg
    DSCN2939 (Medium).jpg
    89.6 KB · Views: 272
  • DSCN2943 (Medium).jpg
    DSCN2943 (Medium).jpg
    93.5 KB · Views: 241
  • DSCN2942 (Medium).jpg
    DSCN2942 (Medium).jpg
    89.5 KB · Views: 247

77bronco_ed

Bronco Guru
Joined
Jul 3, 2004
Messages
1,793
It looks nice... What did you do to bring it down lower for the pictures?

It must not be low enough for ya yet?
 

behemoth

Bronco Guru
Joined
Jul 2, 2003
Messages
1,736
When I did the lowering my focus was on the front ride height and not cutting the bed.

I chose air bags for the rear to allow me to adjust the height as needed. So when I arrived at fab fords I aired down for this look. Its not a big drop, just an inch or two. I can drive it at this height but I hit the bump stops when I hit bumps.

So To keep this ride height I will have to trim some more out of the notch and french in the bump stop or move it out of the notch.
 
OP
OP
greatguy57078

greatguy57078

Contributor
Bronco Guru
Joined
Jul 15, 2006
Messages
3,430
I am getting back into the swing...kinda? I am sidetracked right now cause the boy wants to drive the halfcab to prom this weekend. yeah....caught me right in the middle of swapping to disc brakes so I can slap on the big tires. I am VERY close to pulling the body off to set on the street rod frame, so an update is coming. Trust me, I am not a man with alot of patience..... so bear with me!:-X
 
OP
OP
greatguy57078

greatguy57078

Contributor
Bronco Guru
Joined
Jul 15, 2006
Messages
3,430
Well ...alright. If you really want to know it all started when I saw that low half that Duffy built a looooooong time ago!
 

Broncobowsher

Contributor
Total hack
Joined
Jun 4, 2002
Messages
37,111
Here are some pics of its current and close to final state. I think when the time comes for paint I will paint it the same brown color again.

I will be dropping the rear lower to achieve this ride height, it will require some bed floor cutting as well as some rear inner fenders.

After looking at those pictures, I was thinking about the ride Todd gave me in the red racer at the Stampede in March. It just had a couple of little plexi wind deflectors that worked amazingly well. I wonder what your Bronco would look like without the windshield and only a little wind deflector for each seet. I am thinking of some of those late 50's to mid 60's road race cars that were similer. I think there was a famous thunderbird that was that way as well as a few others. As well as the Stoppe racer too.
 

behemoth

Bronco Guru
Joined
Jul 2, 2003
Messages
1,736
I am looking at the possiblilty of removing the steel at the top of the windshield.
 
Top