• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

What have you done to your Bronco today?

Adarcy

Sr. Member
Joined
May 19, 2010
Messages
826
I've been having a great time just driving it the last two weeks since installing power steering. Then I said it "it hasn't run this good in 2 years". Got home and found a gas leak. Doh!
 

markperry

Bronco Guru
Joined
May 8, 2009
Messages
4,175
Installed the carpet and front seats. Placed the cage and drilled holes for mounting bolts. Prepped rear seats for install with longer bolts. The plan is to paint the cage flat black, but I don't have time for that right now, so primer it is.

660BA5B5-EB0A-4E30-90A3-65584C524B48-3808-000002CD9B1028FE.jpg


7FED1E8C-7CFF-48B7-B352-93C3E3CD04CA-3808-000002CD7C3E746E.jpg


3BF082E9-0133-4BE7-8E4D-16E003902AA3-7817-000005F46C716E08.jpg


D2E93008-47A1-44D5-8289-6D12BBE3E81D-3653-000005951DEC9561.jpg


528028BC-2FFE-4C67-A98A-3A9449F69FB6-3653-00000595255B1FD7.jpg

Is that rollcage from Tom's?
 

jcpetrson

Sr. Member
Joined
Aug 26, 2012
Messages
435
I bought a 60 gallon compressor from Lowes. My wife swung by to pick it up after work. They didn't have it ready so they will deliver it tomorrow with a $25 gift certificate. Winner!
 

Vincen

Contributor
Sr. Member
Joined
Nov 24, 2012
Messages
369
Big Orange 70

This is my 3rd Bronco but the 1st since I totaled a totally restored 69 Sport in 2000. I bought my 70 in late November at which time it ran, had a rust free body but with a bunch of dents. I focused just on the drive train, stopping, seeing, fuel system and the suspension. Before May I will be adding:

Power Steering Conversion
IDIDIT Tilt Column w/ Tom's Leather steering wheel
Adjustable Trac Bar
AAW Re-wire kit
Dash and door panels out for powder coating
Rebuilding heater box
Patching a bunch of unexplained holes in the tub
Coating the entire tub with POR15
firewall insulation
Getting gauge cluster refurbished
All new switches
All new weather stripping.

Then it's time to drive it for the summer (or until I can afford to finish the body)
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,651
I don't mean to brag... :)

Go ahead and brag. I remember being impressed that you even knew the factory spec in the first place!

Thanks for the link too.
In that image of one of our master cylinders, it's hard to really see the detail, but that little 3/4" to 1" long bullet-thingy there next to the plugs (to block off whichever ports you don't use) is the piston spacer. It's not so much "adjustable" as it is "settable" depending on what type of rod length your particular setup has.

Thanks Fireball. Good to get the chance to talk to you on the phone. Glad you got some work done on it.
Oh, and as for what I did on my Bronco today... I walked past it.
Twice!

Paul
 

gnsteam

Contributor
Bronco Guru
Joined
Jan 29, 2010
Messages
4,148
Loc.
Lincoln NE
Yesturday afternoon I was driving home from work when, suddenly the Bronco started running like crap.:eek:%) Luckily I was able to limp it home to the garage. I wasn't able to look at it till this morning. What I found was the engine was getting to much fuel and flooding itself. What had happened was the float retaining clip that attaches to the float pivot shaft, and snaps into a groove on the back side of the float seat body, came unsnapped from this groove. Allowing the float To raise up to the top of the fuel bowl, thus over filling the bowl and flooding the engine. Not sure why It came loose, so I gave it a little extra bend to make it snap on a little tighter.;D A simple no cost fix, but I did have to burn a vacation day. So I made good use of my time and hooked up the timing light, tach and vacuum gauge. And proceeded to fine tune the carb. Then my son and I went to lunch and a long drive.;D
 

bknbronco

Bronco Guru
Joined
Jan 17, 2011
Messages
4,388
Loc.
North Metro, MN
i havent done anything for a few months mostly because its 5below outside and also because i ran out of funds. I cant wait for spring so i can fire it up again. No big mods in the near future, just drive it, beat on it a little, and drive it some more. Its nice owning a 40year old truck that you dont have to work on all the time. Sure i could do alot of things to it like disk brakes, power steering, and a rool cage, but im more into enjoying the drive than working on it lately.
 

wesleydax

Full Member
Joined
Apr 12, 2011
Messages
331
got to drive it to work today, 22 deg and the fast efi did excellent. started first time and ran good.
 

ugly74

Bronco abuser
Joined
Apr 17, 2006
Messages
2,856
Loc.
Colorado
Fired her up and went for a spin. Startled a neighbor walking her dog when i came around the corner sideways! I didnt even get close to her, but she sure gave me a funny look.
Went to the store, came home and found a road that still had maybe 6 inches of snow on it. That was fun
 

bknbronco

Bronco Guru
Joined
Jan 17, 2011
Messages
4,388
Loc.
North Metro, MN
Thats ausome! Im glad you guys arnt afraid of driving a classic in the snow! WAY TO GO!!

The funny look is her trying to figure out what the heck you were driving. Kinda looks like a jeep but only better. Thats what that look was!
 

Unknown

Sr. Member
Joined
Jan 21, 2012
Messages
695
Looks like I'm pulling my PTO set up. Found a donor D20 - gonna clean her up and replace the seals and swap out.
 

wesleydax

Full Member
Joined
Apr 12, 2011
Messages
331
Got to drive it around in a little snow, learned the value of a good seal between top and windsheild. snowing came in through the crack, o well it was still fun
 

Attachments

  • snow.jpg
    snow.jpg
    97.1 KB · Views: 92
Top