• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

What have you done to your Bronco today?

OP
OP
Heus33

Heus33

Bronco Guru
Joined
Jun 1, 2005
Messages
7,488
Built these little beauty's for a member here:

[youtube]zwId9oRrQxE[/youtube]
 

Burkulater

Full Member
Joined
Mar 30, 2011
Messages
316
Loc.
Lancaster, PA
Went to see Nick,

Swapped for better driveshafts
Picked up referbed steering wheel
Non shifter column sleeve
Early column bezel
Early taillight lenses and one bucket
Horn
Elec wiper switch bezel pigtail knob
Side marker pigtails
Washer tank
New speedo glass
Late style front license plate bracket I'm gonna use on the rear
Throttle linkage
Footmans loop and the block for the driver seat

And a few parts for member fireball05 and some beer and prob some other stuff too
 

Fireball05

Bronco Guru
Joined
Oct 7, 2012
Messages
1,822
Burk - sounds like a darn good trip! Thanks for your help, much appreciated.

While you were running out to Philly I spent an embarrassingly long time agonizing over installing the glovebox door with perfectly even gaps on all 4 sides.

For those counting at home the glovebox and door assembly contains no fewer than 8 screws and 11 nuts and bolts! That's a lot of stuff to fiddle around with and $10 worth of stainless hardware.
utysuja4.jpg


agu6yja8.jpg
 

jcpetrson

Sr. Member
Joined
Aug 26, 2012
Messages
435
Yesterday I patched the last hole in the firewall. It's a good thing the previous owner didn't own a boat.
 

Rox Crusher

Bronco Guru
Joined
Dec 13, 2008
Messages
2,830
Burk - sounds like a darn good trip! Thanks for your help, much appreciated.

While you were running out to Philly I spent an embarrassingly long time agonizing over installing the glovebox door with perfectly even gaps on all 4 sides.

For those counting at home the glovebox and door assembly contains no fewer than 8 screws and 11 nuts and bolts! That's a lot of stuff to fiddle around with and $10 worth of stainless hardware.
utysuja4.jpg


agu6yja8.jpg

that turned out really nice. I couldn't get mine that tight looking.
 

admin

Administrator
Just your friendly, neighborhood webmaster...
Joined
Jan 1, 2001
Messages
38,897
Loc.
Phoenix, AZ
I took mine out for a spin and got the emissions test I've been putting off. Passed with flying colors. :)

But on the 15 minute drive I was reminded of several little things that need attention; heater core leaking slightly, heater plenum flap doesn't open correctly, choke is stuck so it idles at 2,000 RPM unless you really jab the gas pedal. It's always something!
 

Revelation

Bronco Guru
Joined
Oct 9, 2004
Messages
4,825
Getting ready to load it on a trailer and head to Perry, gonna drive her to work a few days this week.
Now if I was comfortable with the F-150 on the trailer being pulled by the Bronco, HUMMMMMMMMM
 

roundhouse

Bronco Guru
Joined
Sep 5, 2003
Messages
2,956
Plugged the mystery hole behind the passenger head Yesterday ImageUploadedByTapatalk1360532407.167014.jpg

Drive it to church this morning
Spent bout an hour in te parking lot after church teaching ( or attempting)my 14 yr old how to drive a manual trans

Pretty sure I heard the u joints groaning in protest.
And I might need a chiropractor now.
 

Revelation

Bronco Guru
Joined
Oct 9, 2004
Messages
4,825
Spent bout an hour in the parking lot after church teaching ( or attempting)my 14 yr old how to drive a manual trans

Pretty sure I heard the u joints groaning in protest.
And I might need a chiropractor now.

4 low is an excellent tool for teaching someone to drive a stick, even better if you have twin sticks, if not just leave the hubs unlocked.
 

jcpetrson

Sr. Member
Joined
Aug 26, 2012
Messages
435
I got it out for a quick spin up/down the street. Without a hood, fenders, etc., I think my neighbor believes I'm nuts.
 

BLAZEOFGLORY

Sr. Member
Joined
Jan 30, 2006
Messages
733
Made me a new fan shroud and finished the lights, almost done with engine install now going to finish the remounting of the front seats. Here's some EYE candy
 

Attachments

  • Right side wire loom done.jpg
    Right side wire loom done.jpg
    157.3 KB · Views: 61
  • Left side wire loom done.jpg
    Left side wire loom done.jpg
    223.7 KB · Views: 57
  • Driving lights 1.jpg
    Driving lights 1.jpg
    58.4 KB · Views: 60
  • Driving lights 2.jpg
    Driving lights 2.jpg
    63.9 KB · Views: 57
  • New Fan Shroud 1.jpg
    New Fan Shroud 1.jpg
    177.6 KB · Views: 64
  • New Fan Shroud 2.jpg
    New Fan Shroud 2.jpg
    116.7 KB · Views: 52
  • New Head lights.jpg
    New Head lights.jpg
    74.9 KB · Views: 51
  • Alice convertion.jpg
    Alice convertion.jpg
    77.4 KB · Views: 53

broncoman1972

Bronco Guru
Joined
Mar 4, 2004
Messages
1,300
Realized the fuse panel mount I made for the ashtray won't work. Need to turn the panel sideways...


Sent from my Eye Phone
 

BronCowie

Contributor
Old Timer
Joined
Apr 24, 2007
Messages
8,291
Loc.
Vancouver, WA
Made a couple of extension brackets for my door straps so they don't get pinched in between the cage down tubes and the kick plates. Thanks to "Nelson" for inspiring me to do this. They will be powder coated soon.

DSCN3033_zps7b5e9a19.jpg


DSCN3037_zpsed3c3264.jpg
 
Top