• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Caster/Camber Ball-joint Sleeves

u10072

Bronco Guru
Joined
May 18, 2007
Messages
2,249
Hello All,
I have looked all over-- anyone know the Moog part numbers for the adjustable upper caster camber balljoint adjustment sleeves?

thanks,
Matt
 

patkelley

Full Member
Joined
Apr 16, 2010
Messages
168
Loc.
Marietta
How much time to install these?

You can do it with the tire on - remove upper ball joint nut, use special tool to remove threaded sleeve, install new thinner sleeve (with special tool) and push in eccentric sleeve.

Easiest if you lift the wheel off he ground.
 
OP
OP
u10072

u10072

Bronco Guru
Joined
May 18, 2007
Messages
2,249
Next question for those who have used these-- are these something that you buy prior to going to the alignment shop and getting everything done or should you just install the factory style units and get them if you need them. What I am thinking is to get them to be able to max out the the caster regardless of the number. I am guessing you would want to get the ones you need after you get the alignment.

On the SPC website they say a half hour for install.
 
OP
OP
u10072

u10072

Bronco Guru
Joined
May 18, 2007
Messages
2,249
It looks like the SPC are more specific to your needs and the napa are more like you install at the time you do the upper ball joint.
 

garberz

Bronco Influencer
Joined
Jun 24, 2007
Messages
6,864
Loc.
Conejo Valley, Ca.
Next question for those who have used these-- are these something that you buy prior to going to the alignment shop and getting everything done or should you just install the factory style units and get them if you need them. What I am thinking is to get them to be able to max out the the caster regardless of the number. I am guessing you would want to get the ones you need after you get the alignment.

On the SPC website they say a half hour for install.

I've never taken mine to the alignment shop. Thousands of miles on my KM2's, they're wearing just fine. I put those 1 1/2's in to gain max caster. It could still use more caster, even with the 7* "C" bushings. Eventually I'll cut and turn the yokes, run 2* bushings and remove the eccentrics.

Mark
 

Timmy390

Contributor
Bronco Guru
Joined
Jan 1, 2011
Messages
5,948
Loc.
Conway, AR
Until you hit the alignment shop you don't really know what you need.

SPC and the NAPA bushings are the same thing and both install the same way. You will have to remove the upper ball joint nut and then remove the factory/standard bushing already installed then install the "degreed" one. Both are installed with the same tool. Think it's called a spanner socket? Bought mine at NAPA ($13) when I bought my ball joints.

Once the alignment shop gives you the numbers you will know which ones to order. Heck, it might be so far off you need to install different degree C bushings. The switch from 4 to 7 degree C bushings made my rig drive like a dream.......

Tim
 

surfer-b

Contributor
Bronco Guru
Joined
Sep 7, 2006
Messages
3,013
You will have a difficult time removing or installing the bushings unless you get the pressure off them, I have always dropped the knuckles. When the ball joints are torqued down it applies pressure to the bushings. This has worked for me, others may have a diff way.
1: remove tire and wheel
2: remove nut on top ball joint
3: loosen nut on bottom so knuckle will drop a little but not fall out on ground
4: take hammer and hit the yokes where the knuckle ball joints are and let harmonics work for you, once the knuckle drops you will be able to remove and install the bushings with no problems.
 

garberz

Bronco Influencer
Joined
Jun 24, 2007
Messages
6,864
Loc.
Conejo Valley, Ca.
You'll probably need the spanner socket to remove the factory concentric bushing, but not for installing the eccentric one's. They don't torque down, you just thread them down about an 1/8" from the top. That's it. No preload.

Tim, what are your caster specs, with the 2 1/2" coils and 7* bushings?
 

Timmy390

Contributor
Bronco Guru
Joined
Jan 1, 2011
Messages
5,948
Loc.
Conway, AR
Tim, what are your caster specs, with the 2 1/2" coils and 7* bushings?

Funny story....I don't know.....LOL I never got back to get the numbers.

My rig drove like CRAP all over the road all symptoms pointed to not enough caster. I took it to the alignment shop and they told me all they could set was the "toe" and wanted like $45 to give me the numbers......I declined

Had the rig apart for a regear and added the 7 degree C's as recommended by several here on the board. After the regear and disc brake install, I set the toe myself and went for a spin......dang rig drives like a dream so I never went back to get numbers. No funny ware on the tires, it tracks and returns to center at all speeds......

Tim
 

garberz

Bronco Influencer
Joined
Jun 24, 2007
Messages
6,864
Loc.
Conejo Valley, Ca.
Tim, that's pretty much the same story with mine. It drives so nice on the highway, I never felt it was necessary to take it to a shop. I will get the specs on what it is now, before I cut and turn the yokes.
 

bfluegel

New Member
Joined
May 8, 2008
Messages
33
SPC and the NAPA bushings are the same thing and both install the same way.
Tim

Are they really the same? I got the Moog (Part number K936) and they look just like the photo on the NAPA site. But they sure don't look like the drawing on the SPC instructions. The SPC appear to be one piece and the Moog/NAPA are two pieces.
 

Timmy390

Contributor
Bronco Guru
Joined
Jan 1, 2011
Messages
5,948
Loc.
Conway, AR
Are they really the same? I got the Moog (Part number K936) and they look just like the photo on the NAPA site. But they sure don't look like the drawing on the SPC instructions. The SPC appear to be one piece and the Moog/NAPA are two pieces.

I'm going off the link garberz posted up top (http://www.spcalignment.com/index.ph...&pid=23012) and what I've seen and held in my hands at NAPA. A ball joint incert is a ball joint incert just some are tapered and others aren't. New ball joints come with the non tapered incerts.

Post a link to what you're seeing? 2 piece? must be an apples and oranges thing.....lol

Tim
 

Timmy390

Contributor
Bronco Guru
Joined
Jan 1, 2011
Messages
5,948
Loc.
Conway, AR
Tim, that's pretty much the same story with mine. It drives so nice on the highway, I never felt it was necessary to take it to a shop. I will get the specs on what it is now, before I cut and turn the yokes.

Next set of tires I buy, I'll get them to throw in a numbers check for free....or try anyway......LOL

Tim
 

garberz

Bronco Influencer
Joined
Jun 24, 2007
Messages
6,864
Loc.
Conejo Valley, Ca.
Are they really the same? I got the Moog (Part number K936) and they look just like the photo on the NAPA site. But they sure don't look like the drawing on the SPC instructions. The SPC appear to be one piece and the Moog/NAPA are two pieces.

The SPC is two pieces, the other piece not shown is a tapered washer that sits on top, so you can torque down the castle nut.

Mark
 

bfluegel

New Member
Joined
May 8, 2008
Messages
33
I'm going off the link garberz posted up top (http://www.spcalignment.com/index.ph...&pid=23012) and what I've seen and held in my hands at NAPA. A ball joint incert is a ball joint incert just some are tapered and others aren't. New ball joints come with the non tapered incerts.

Post a link to what you're seeing? 2 piece? must be an apples and oranges thing.....lol

Tim

I've only seen the Moog (left photo), but it doesn't look like the SPC from the link above (right photo). The Moog sleeve is not tapered, and it is much thinner than the one in the SPC photo, because the hex-head piece goes inside. The hex head piece is tapered.
The stock ball joints I've seen come with a sleeve that is tapered, albeit concentric and no offset angle.

Brian
 

Attachments

  • K936.jpg
    K936.jpg
    8.5 KB · Views: 144
  • SPC.jpg
    SPC.jpg
    14.3 KB · Views: 122

Timmy390

Contributor
Bronco Guru
Joined
Jan 1, 2011
Messages
5,948
Loc.
Conway, AR
That clears it up....Sorry for the confusion. I was only shown the incert at NAPA the second piece must have been in the box.....

Again, sorry if I cause any confusion........

Tim
 
Top