• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

New motor, same problem.

OP
OP
Okie69

Okie69

Contributor
Sr. Member
Joined
Nov 28, 2011
Messages
842
The wife thinks I'm crazy by the way...I keep running to the garage to check/ take pictures of things.
 
OP
OP
Okie69

Okie69

Contributor
Sr. Member
Joined
Nov 28, 2011
Messages
842
Borrow the carb off the ole man's Bronco.;)

This is going to be shocking, but he sold his. Got too old to mess with it when it broke down haha he still loves to go for rides in mine though.
 

half cab

Contributor
Guru Bronco
Joined
Dec 8, 2010
Messages
16,311
This is going to be shocking, but he sold his. Got too old to mess with it when it broke down haha he still loves to go for rides in mine though.

Dawg gone ...I'm with the others on it being a carb or vacuum issue.
 
OP
OP
Okie69

Okie69

Contributor
Sr. Member
Joined
Nov 28, 2011
Messages
842
I think I'll probably just get a replacement tomorrow and hope to hell that it fixes it.
 

jckkys

Contributor
Bronco Guru
Joined
Mar 15, 2012
Messages
5,221
It's amazing how many approach engine problem diagnoses by replacing parts with new ones until the engine runs correctly. Any fleet mechanic would be fired for using this approach, because his employer would otherwise go broke. I see no reason to believe the original engine needed to be replaced.
The distributor may not have been installed correctly,the fuel line could be obstructed ie (plugged fuel filter or pick up screen), and many others. Search loss of power trouble shooting. To buy after market parts while having no reason to believe the originals were in any way defective is absurd. The originals were time proven and dependable when properly maintained, far more so than offerings by the aftermarket. Literature to walk you through the trouble shooting process will always refer to the assumed original parts.
 

broncnaz

Bronco Guru
Joined
May 22, 2003
Messages
24,342
Well he did say he had low compression on a few cylinders on the orginal engine. He has also rebuilt the current carb. If I remember we have walked through some of this before with him on the orginal engine. So its not like nothing was done and he's just replacing parts. Maybe some of us should take our own words to heart.
Few of us here are fleet mechanics or even just automotive mechanics by trade so there common place procedures followed by professionals are not always practiced by the hobbiest.
You also have to look at the other side not everyone has the time or wishes to fool with every little part again so in some cases they will try new parts. Some are simple upgrades that may or may not help but something they may have wanted to do anyhow. Many come here for a crash course in troubleshooting so they dont have to go through all the steps and whatnot.
 
OP
OP
Okie69

Okie69

Contributor
Sr. Member
Joined
Nov 28, 2011
Messages
842
I replaced the original motor after finding out a couple of cylinders were only at 60 lbs or so. I thought that pretty much told me it was something serious internally. I've rebuilt the carb and had two different people tune it for me. I've replace the entire fuel delivery system except for the tank itself. Plugs and wires are new and ignition system is known good after testing it on another bronco. I may be a novice at best when compared to most of the guys on here, but I think I've covered a lot of bases without just throwing new parts at it. (The things I did replace were otherwise deteriorated or just more convenient to replace with the new motor.)
 

treihesse

Bronco Guru
Joined
Aug 1, 2008
Messages
1,459
If buy replacing normal tune up and wear items to diagnose im all for that. Most shops have many more tools than most of us therfore I would expect them to run more tests. When I was running a carb I always did this when it was acting up. Fuel filter, cap and rotor, regap plugs, take apart carb and clean, check plug wires for cracks or header burns, points or electronic ignition, I would do it in stages so I could figure out what was wrong. .cost less than a tune up at a shop..
 
OP
OP
Okie69

Okie69

Contributor
Sr. Member
Joined
Nov 28, 2011
Messages
842
If buy replacing normal tune up and wear items to diagnose im all for that. Most shops have many more tools than most of us therfore I would expect them to run more tests. When I was running a carb I always did this when it was acting up. Fuel filter, cap and rotor, regap plugs, take apart carb and clean, check plug wires for cracks or header burns, points or electronic ignition, I would do it in stages so I could figure out what was wrong. .cost less than a tune up at a shop..

Thanks, I'll go through all of those things before spending the money for a new carb.
 

WheelHorse

Bronco Guru
Joined
Nov 22, 2004
Messages
2,511
When it's running rough, can you see black smoke coming out of the exhaust?

Without knowing the first question, also, double check that you can blow through the fuel filter.

Reverse blow through it onto a paper plate and see if a bunch of crud comes out of it. Also, have you gone through your fuel line, traced it all the way back, to see if there's another filter in line or that it's free and clear?

Don't rule out the fuel pick up has the metal strainer / or filter sock attached to it. Ethanol crystals could be robbing you of fuel volume. I had this happen on a Poncho 400. She'd run ok for a few blocks and then run like a complete dog. Long story short, the fuel sock was about plugged in the thing.
 
OP
OP
Okie69

Okie69

Contributor
Sr. Member
Joined
Nov 28, 2011
Messages
842
I've replaced the entire fuel system from the tank outlet to the carb haven't done anything inside of the tank though. Inline fuel filter with pump and clear filter by the carb. I can see crap floating in the clear filter.
 
OP
OP
Okie69

Okie69

Contributor
Sr. Member
Joined
Nov 28, 2011
Messages
842
When it's running rough, can you see black smoke coming out of the exhaust?

Without knowing the first question, also, double check that you can blow through the fuel filter.

Reverse blow through it onto a paper plate and see if a bunch of crud comes out of it. Also, have you gone through your fuel line, traced it all the way back, to see if there's another filter in line or that it's free and clear?

Don't rule out the fuel pick up has the metal strainer / or filter sock attached to it. Ethanol crystals could be robbing you of fuel volume. I had this happen on a Poncho 400. She'd run ok for a few blocks and then run like a complete dog. Long story short, the fuel sock was about plugged in the thing.

To answer the first question there is no smoke of any kind except for the puffs of white smoke that come out of the top of the carb haha
 

treihesse

Bronco Guru
Joined
Aug 1, 2008
Messages
1,459
If you have sediment in the second filter imagine whats in the first one. I would drain the gas and drop the tank and start there. Any tiny pieces of material will collect in jets, passages and anywhere else in between. Clean fuel is number one. If that tank is original I will bet its full of sediment. Its not fun but its kinda important to have a clean tank. Ive had similar issues and it goes like this. Replace filter runs great , clogs , replace filter, runs great clogs. I still think Its a carb issue but sediment in the gas could have been the start of it
 
OP
OP
Okie69

Okie69

Contributor
Sr. Member
Joined
Nov 28, 2011
Messages
842
If you have sediment in the second filter imagine whats in the first one. I would drain the gas and drop the tank and start there. Any tiny pieces of material will collect in jets, passages and anywhere else in between. Clean fuel is number one. If that tank is original I will bet its full of sediment. Its not fun but its kinda important to have a clean tank. Ive had similar issues and it goes like this. Replace filter runs great , clogs , replace filter, runs great clogs. I still think Its a carb issue but sediment in the gas could have been the start of it

That sounds like a good idea I think that's the way I will go. I figured the two filters would get most of it but I guess not. It's starting to sound like I've gotten crap into my carb at some point.
 
OP
OP
Okie69

Okie69

Contributor
Sr. Member
Joined
Nov 28, 2011
Messages
842
And I got a new carb at the parts store it will be here in the morning so you guys think it would be counterproductive to hook it up without cleaning the tank out first?
 

treihesse

Bronco Guru
Joined
Aug 1, 2008
Messages
1,459
No I would hook it up. Put a new clear filter on. If it runs good you Know it was your carb. I would still drop the tank and clean it for peace of mind
 

Rustytruck

Bronco Guru
Joined
Feb 24, 2002
Messages
10,872
If you look at the picture of your old carb the distrubiter vacuum should be hooked up on the fitting under the front bowl on the drivers side. It looks like you have the vacuum hooked up on the passengers side of the carburator. That is full manifold vacuum. It will screw up your vacuum advance and your timing settings for the distributer. Fix that before making major changes.
 
Top