• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Bouncing voltmeter and pulsating headlights

broncofiresmith

Sr. Member
Joined
May 6, 2006
Messages
416
I saw this thread about trying a voltage regulator from 78 Granada I went to Napa to get one but it has a square plug instead of the round one. Did I get wrong one or do I need to change ends?

Thanks

Early thread I saw in the archives.

"If you're looking at the stock gauge in the cluster, it's an Ammeter. Measures current flow, not voltage. Not that that really means anything about your question. The bouncing is the mechanical voltage regulator keeping the proper charge on the battery. Points open... points closed.... points open... etc. If you don't like the bouncing, I've read that you can replace the mechanical one with an electronic one from a 78 Granada."
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
Something's not right, but without a pic it's hard to tell which one is wrong.
Square isn't right sounding though, for any Ford regulator, so that new one sounds suspect.

Is your old one a flat and rectangular 4-position connector with just 3 positions filled? If so, that's pretty much the standard regulator design for all early Ford cars and trucks, so I'm not sure what Napa was trying to sell as a replacement. Wrong part in the box maybe?

Is your '74's regulator back on the firewall, or over on the fender or skirt? Just curious.

Try asking for one for your year Bronco. By now they should all be electronic replacements like the Granada ones were early on. If not, maybe they give you choices like I've seen in years past?

And last question, but did this just start out of the blue? Been doing it for awhile now? Or did it happen after changing something like an alternator or some wiring?

Paul
 

Broncobowsher

Contributor
Total hack
Joined
Jun 4, 2002
Messages
37,112
Need pictures. Can't think of a round voltage regulator plug you speak of.
 
OP
OP
broncofiresmith

broncofiresmith

Sr. Member
Joined
May 6, 2006
Messages
416
Something's not right, but without a pic it's hard to tell which one is wrong.
Square isn't right sounding though, for any Ford regulator, so that new one sounds suspect.

Is your old one a flat and rectangular 4-position connector with just 3 positions filled? If so, that's pretty much the standard regulator design for all early Ford cars and trucks, so I'm not sure what Napa was trying to sell as a replacement. Wrong part in the box maybe?

Is your '74's regulator back on the firewall, or over on the fender or skirt? Just curious.

Try asking for one for your year Bronco. By now they should all be electronic replacements like the Granada ones were early on. If not, maybe they give you choices like I've seen in years past?

And last question, but did this just start out of the blue? Been doing it for awhile now? Or did it happen after changing something like an alternator or some wiring?

Paul

Thank you for your help. I will get a picture today. It has been happening for many years but I just now thought I should try to do something about it. It is mounted on the drivers side inner fender skirt. The wire come out and plug into I think 2 round connectors but I'm not sure, I will look today and get a picture. Thanks again.
 

01JLH

Sr. Member
Joined
Sep 3, 2007
Messages
392
If you are looking at the square box with 2 round connectors on the Drivers side inner fender, you are looking at the DuraSpark ignition box. The Voltage regulator is probably on the passenger side firewall or inner fender just behind and beside the battery. Ignition box has nothing to do with voltage regulation at all.
 
OP
OP
broncofiresmith

broncofiresmith

Sr. Member
Joined
May 6, 2006
Messages
416
If you are looking at the square box with 2 round connectors on the Drivers side inner fender, you are looking at the DuraSpark ignition box. The Voltage regulator is probably on the passenger side firewall or inner fender just behind and beside the battery. Ignition box has nothing to do with voltage regulation at all.

That's is thanks
 

zonian

Sr. Member
Joined
Nov 5, 2013
Messages
764
Loc.
St. Augustine
Ditto on the passenger side inner fender, I just replaced mine with one from Auto Zone, didn't cost much, easy to swap....
 

70_Steve

Old Guy
Joined
Dec 13, 2002
Messages
8,317
Make sure you mount the regulator to the inner fender before plugging in the connector!!! The regulator depends on the mounting for a ground, and you can Fubar the regulator if you plug it in first.
 
OP
OP
broncofiresmith

broncofiresmith

Sr. Member
Joined
May 6, 2006
Messages
416
Thank you for your help it works great. I even get ambitious and fixed my instrument lights today.
 
OP
OP
broncofiresmith

broncofiresmith

Sr. Member
Joined
May 6, 2006
Messages
416
Installed a new voltage regulator that fixed the pulsating headlights and bouncing gauge. On the dash label lights it was dirty terminals and bad ground.
 

R.P. Coltrane

Jr. Member
Joined
Sep 11, 2014
Messages
147
Loc.
Iowa, the flat part
Glad you got it fixed, congrats! Flickering is annoying

If you go through it again, IMO there's no need for the 78 granada regulator, in the last 15 years pretty much all of the replacement brands have gone to solid state operation and done away with the old style mechanical switch internals.
 

Casey835

Sr. Member
Joined
Mar 8, 2008
Messages
759
I have a bouncing voltmeter and pulsating heAdlights but with a 3G alternater with the voltage regulater on the back of it for bout two years now. Doesn't seem to cause any issues other than annoying. Could voltage regulator be my problem? Seeing this thread just brought it back up for me.
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
Seems like the most possible culprit Casey. But even then I suppose it's not guaranteed.
In the meantime, here are a few questions:

1. Does your alternator have a good clean physical connection to the engine block? No paint, rust or grease in other words?

2. Are you using the original wiring, or do you have an upgrade harness between the alternator and battery?

3. Have you added grounding circuits to all the major components? From the battery to the: Engine, body, frame, etc.

4. Anyone with a known-good 3G you could temporarily trade to see if that's the obvious issue? This last is a long-shot, but if you know other vintage Ford owners you hang out with, that might be a possible shortcut to testing if all the other stuff is good.

Good luck.

Paul
 

Casey835

Sr. Member
Joined
Mar 8, 2008
Messages
759
1. I will say yes but will check again as everything is new.
2. New EZ wiring harness thru out with RJM 3G wiring harness.
3. Wildhorses headlight harness. I do need to check the body to frame and engine.

As I stated earlier, issue has been there since rebuild. I've just let it go because it doesn't seem to affect anything. I've also noticed the tach doesn't drop all the way down when ignition is switched off.
 
OP
OP
broncofiresmith

broncofiresmith

Sr. Member
Joined
May 6, 2006
Messages
416
I thought all was good with mine but today while driving it bounced. No bouncing while sitting there or no headlight pulsating but bouncing. I checked the ground and cleaned it but still no luck.
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
I thought all was good with mine but today while driving it bounced. No bouncing while sitting there or no headlight pulsating but bouncing.

What did you do to reduce the instance of it bouncing? Whatever you did, at least it helped!
Now, with these old gauges, especially one that's been bouncing for a long time, perhaps it's just losing some of it's needle dampening and your bouncing-while-driving issue is now strictly from the gauge itself being old?
Next time the engine is off or you're just sitting there and it's not bouncing, give the cluster or dash a few tapes to see if it bounces. No need to break the glass of course! But a little bang next to the gauge might showcase it's weakness, if there is any.


I checked the ground and cleaned it but still no luck.

Which ground? Just so you know, if there is only one, that's not enough. Nor is it original.
Reason I say that is that even though EB's got the dregs when it came to sophisticated wiring, even Ford saw fit to make to major grounding points in the engine compartment.
One was the engine of course, as the main connection to the battery's negative terminal. But the other was the body at the inner wheel well. Probably a small hole in the sheet metal right there facing the exhaust manifold near the front corner of the wheel house.

If your cable was ever changed, chances are better than not that it did not get reconnected to the body. If not, you should definitely make this a priority. Updating all your grounding scheme as well.
A good place to start is the body from the battery, as just mentioned, but another good one would be to make a strap or wire or cable and attach it between the engine and body. This is usually most convenient near the back of the intake manifold to the firewall. Several places there you can attach to without using one of the intake manifold attaching bolts. They work, but best to leave them alone and not create a leak by removing one temporarily.

I usually add one between the engine and the frame too, but most think this is overkill. I think overkill is just enough when it comes to grounds and battery cables. The more and larger, the better!

Paul
 
OP
OP
broncofiresmith

broncofiresmith

Sr. Member
Joined
May 6, 2006
Messages
416
Thank you for your help. I am going to take your advice and put two grounding straps on it. I installed a new voltage regulator which fixed it at idle. I tapped the instrument cluster today and the ammeter didn't move at all. I will post a update when I get the additional straps installed.

Thanks again.
 
Top