• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Updating to Dana 44 on 69

moses_m

Full Member
Joined
May 5, 2013
Messages
262
Updating to Dana 44 this year for the dunes. Broke pinion on 30 last year near glamis. Thinking of running 4.56 gears. 302 roughly 380 hp. NV3550 with 33s pending approval for 35s. Bronco used around town, highway, and dunes. If a 350 cheby Heep pulls up next to me I will be gunning it up the dune. Please help me make a wise decision. edlebrock heads edlebrock air gap intake. crane cam with specs attached. currently running a 1407 edlebrock which I will probably change but thats for another thread.
 

Attachments

  • Cam_Spec.pdf
    35.3 KB · Views: 152
OP
OP
moses_m

moses_m

Full Member
Joined
May 5, 2013
Messages
262
okay all depends with newer 2.5 lift 2 body. I hit the flares a couple of times on the whoops with the 33s.
 

Jdgephar

Bronco Guru
Joined
Sep 25, 2012
Messages
1,526
If you go with 35's, find/buy Ford disc knuckles so you can use the larger u-joint axle shafts.
 
OP
OP
moses_m

moses_m

Full Member
Joined
May 5, 2013
Messages
262
gonna try to get a new or rebuilt 44. Will 1st gear still be usable with the 4.88 gears? When I am at the dunes I run the j transfer in high high and tranny in first gear then punch it into 2nd at the base of the dune. Have had real good success running up steep dunes that way.
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,651
Sure. It's not really that extreme a difference between the two. What ratio are you running now?
Whether first is useable or not might depend more on just what you consider useable too. It's not like the 3550 has a granny low first gear. It's what? 4.50:1 or something? And you'd still be off-setting some of the difference with the larger tires.

Since you're using an overdrive trans, I would also recommend the lower differential ratios they were talking about. Anything higher and you'll have a hard time using overdrive on the highway once you go to 35's. They might seem low with the 33's at first, but with a high-revving race 302 like you're sporting, I would think it'd appreciate the lower gearing.

What gears are you running now? What rpm range do you like to run in? EFI or carbureted? The type of cam and induction on the engine might dictate which way you go too, whether 4.56 or 4.88. If you had a torquey lower rpm happy engine, the 4.56's might be just the ticket. But if you're really pushing 380 bhp out of a measly 302 cubic inches, you'd have to be running a pretty big cam that's not happy at lower rpms pushing a Bronco around. Have to have some sort of a very sophisticated EFI setup to keep it happy I would think.

Whatcha got? Any pics of your rig handy?

Thanks

Paul
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,651
I should add that, as you probably already know, the 4.56 ratio is going to be stronger than the 4.88's at least in the front. The rear diff doesn't care, but the pinions keep getting smaller and smaller as you go up numerically in a Dana.

So if that motor of yours is tolerant of lower rpm, the lower the number the better from a strength standpoint. And sand running is one of the harder activities on a drivetrain. Some of the damage done to front diffs often comes from flex as much as application of power.
With your chosen wheeling style, I'd seriously consider trussing the differential. And maybe even running one of the diff covers that pre-tension the bearing caps, like Ford Racing used to offer. I think they still have it for the 8.8 diff, but not sure who offers them for the Dana axles.

When the 30's pinion broke, were you just getting started up the side of a dune and it gave out instantly? Or did it just give out over time?

Good luck.

Paul
 
OP
OP
moses_m

moses_m

Full Member
Joined
May 5, 2013
Messages
262
Thanks

Currently have stock 3.50
stock axles have been replaced as one broke last year along with dana 30 pinion.
Here is a good pic of engine. Since pic have gone to explorer front dress and champ radiator electric fan setup.
Cam specs on first post. Top end is all edlebrock rpm heads,air gap intake and 1407 carb. Original motor rebuilt in 08
EFI hopefully in 2016
 

Attachments

  • DSC01153.jpg
    DSC01153.jpg
    122 KB · Views: 174

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,651
Sorry, totally ignored that link you posted first! Got sidetracked again...

Thanks for the pic. We like pics around here. I didn't actually go to your garage or gallery, but it's nice to see a pic in the threads too.

Paul
 
OP
OP
moses_m

moses_m

Full Member
Joined
May 5, 2013
Messages
262
She starts to get up at 2500
Pinion broke close to the top of dune. Like you stated probably the flexing.
Have never heard of the pre tension caps but will look into it.
Thanks again
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,651
I love Crane stuff in our Fords.
But I'd have to say that your power estimates are pretty optimistic. Even your engine BHP (not rear wheel) is likely much less than you think.
With all the goodies on your list, I'd have to estimate say 280 or less. Probably more in the 250-275 range?
But that's just off the top of my head. Probably a calculator somewhere that could get you super close I would think. You ever tried one of those? Maybe I'm wrong.

Don't get me wrong, that's still a LOT of fun horsepower for an EB, especially with the right gearing, but it's not in the 1hp per cubic inch territory with that mild cam. A near 400 hp carbureted 302 is going to be one crappy street motor in a heavy truck in my opinion.

And your new gears, no matter what you end up getting, are going to be way better than your 3.50's I would have to say. But if you liked the 3.50s at all, then maybe you would in fact be happier with the 4.56 rather than the 4.88's?
Your poor old pinion was stuck in-between a healthy motor, a heavy right foot (necessary for dune-running) and 33 inch tires. The 4-series are going to be much happier.
And so are you I bet!

Were you ever able to use overdrive on the highway with your 33's and 3.50's? Maybe on the flatlands or going downhill only?
Just curious. Know a lot of people that can't quite pull that combination. But they don't have the power you have either in most cases, but the EFI ones do have a little better time of it.

Should be fun the next time you hit the sand!

Paul
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,651
...Have never heard of the pre tension caps but will look into it.

Yeah, they're pretty cool. The heavy castings have an additional two bolts/set-screws and lock nuts that you run down lightly after torquing the cover on. It puts some load on the bearing caps and turns the cover into kind of a "stressed member" of the case assembly.
Pretty clever those racer types!

Paul
 
OP
OP
moses_m

moses_m

Full Member
Joined
May 5, 2013
Messages
262
DYNO 08 383 HP motor and your right 281 at the wheels.

Do yall sell complete differentials with disc brakes axles etc? Didnt see it on website just saw call for pricing in the magazine in the third member section.
 
OP
OP
moses_m

moses_m

Full Member
Joined
May 5, 2013
Messages
262
65 mph 5th gear 2k rpms

Works great around here but when I was on I-5 north of sacremento into oregon I had to constantly drop down to 4th gear in the mountains and give it some gas to use the 5th gear.
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,651
Yeah, don't have complete assemblies. That'd be cool, even if the shipping would be a bear!
Would like to get to the point where we're stocking fully built units, or even just the center section, but with so many gear and diff choices, that'd be a pretty fair-sized inventory hanging around.

So, 383 eh? Hmm, that's pretty impressive from that cam and a 302. This isn't a stroker by any chance, is it?
If not, I've got a lot to look forward to with my build! Not going as big as you though. Using a smaller cam, with similar heads and exhaust. Should be fun.

Paul
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,651
Went like stink on the downhills though, didn't it!
Got some pretty good ups-n-downs going through that neck of the woods for sure.

Still, pulling 2000 rpm in a Bronco is pretty stout in the lower range. Not surprised it would bog a bit going up hills, but if you can leave it in fifth on the flatlands, that's pretty good. I mean these things are just rolling phone booths in the aerodynamic department!

Can't wait to hear which ratio you end up with, and how you feel about it.
From your description, and if you're driving it that extensively on the road, I'm still on the fence. If you were keeping the 33's, I'd say 4.56's hands down. But with 35's in your future, you could go either way.

Paul
 
OP
OP
moses_m

moses_m

Full Member
Joined
May 5, 2013
Messages
262
No stroker just bored out.

Inventory would look nice in new digs.
 
OP
OP
moses_m

moses_m

Full Member
Joined
May 5, 2013
Messages
262
probably leaning with 33s hit the flares a couple of times already at dunes. Old suspension gonna update that as well with yalls 2.5 bilis suspension. Has great reviews
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,651
...Inventory would look nice in new digs.

You bet! Everything looks nicer now. We kicked up some dust a couple of weeks ago, that's for sure. Got it all blown out nicely now though.

You'll have to stop by if you find yourself out on Highway 5 again. Jog on over to 99 and we're right off the highway.

Paul
 
OP
OP
moses_m

moses_m

Full Member
Joined
May 5, 2013
Messages
262
Update
picked up 76 dana 44 from cb member and had 4wheel parts install 4.56
Finished installing 2.5 wildhorses lift in the rear. Updated ford 9 to 31 spline 4.56 gears and grizz locker from toms.
Removed dana 30 and started dressing 44 tonight and ran to some issues.
1. Need a ballpark measurement for knuckles so I can install rims to check back spacing. Current rims have 4 inches. going with heim steering from toms
2. brake lines did not match up. Brake lines from caliper to stainless connection 1 size larger.
3. Need to order traction bar.
 
Top