• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Braking Issues

Bukin 67

Bronco Abuser
Joined
Jul 3, 2008
Messages
2,268
My situation requires stopping power for close to 5000 # of Bronco momentum racing on dirt, and since I'm only running 15" wheels, that has to be done with a smaller rotor.
My current system includes 4 disc Wilwood master with 1-1/8" bore, 4 piston Wilwood caliper rear and 2 piston D52 Wilwood front with 2" pistons. (I already plan on replacing the 2 piston front with a 4).
I have all new lines with a proportioning valve mounted on the firewall about 24" or less from the master.
I'm using a typical aftermarket Bronco vacuum booster combined with a 100% duty cycle electric vacuum backup in case of engine failure. It's always on and only kicks off when the vacuum cylinder is evacuated. I've also replaced the main booster with no change.
This system just won't lock em up on the pavement. Maybe a have a gremlin I don't know about?
I know hydroboost is an option, but I think I'll be taxing the explorer p/s pump too much since I already have the ram assist steering on it.
Anyone gone electric? I'm gravitating toward that, since a hot rod builder buddy of mine has good luck with them, and they'll put out 1300 lbs. or better.
 

toddz69

Sponsor/Vendor
Bronco Guru
Joined
Nov 28, 2001
Messages
11,223
Pwcbr here on this forum has used electric on his FSB and I think he liked it.

Which calipers are you switching to on the front? Be advised that most, if not all, of Wilwood's 4-6 piston offerings in their EB kits offer LESS braking torque than the stock Ford or GM calipers (and your current Wilwood D52 calipers).

How is your pedal height/feel? I think that trying at least a 1" bore master cylinder might be warranted and also perhaps a change in pads with a higher cf.

I'll let Apogee and ntsqd chime in as they are bonafide braking engineers whereas I just play one on the internet :)

Todd Z.
 
OP
OP
Bukin 67

Bukin 67

Bronco Abuser
Joined
Jul 3, 2008
Messages
2,268
Thanks Todd. I was told similar to what you said about my present front 2 piston calipers. I thought 4 piston would be better, but maybe I should keep them?

My master is 1-1/8" bore.

The pedal isn't as firm as I think it should be, although I have bled it thoroughly. I am wondering if the outside bleeder on the calipers needs to be bled as well as the inside? I assumed all the air would be pushed out whichever side you bled from.
 

B RON CO

Contributor
Bronco Guru
Joined
Jun 29, 2016
Messages
2,484
Loc.
Statesville, NC
Hi, I can only give an amateur opinion, taken from years of Saturday night stock car experience. No one we know runs power brakes on a stock car. I know off roaders do and that is probably not your problem. Can you try a different compound brake pad? We run a soft pad on a short track to get into the corner as hard as possible
Another concern is to bed the pads in and let them cool down when they are new. If there.is any glazing on the pads or rotors your performance will be sub par. Good luck
 
OP
OP
Bukin 67

Bukin 67

Bronco Abuser
Joined
Jul 3, 2008
Messages
2,268
Hi, I can only give an amateur opinion, taken from years of Saturday night stock car experience. No one we know runs power brakes on a stock car. I know off roaders do and that is probably not your problem. Can you try a different compound brake pad? We run a soft pad on a short track to get into the corner as hard as possible
Another concern is to bed the pads in and let them cool down when they are new. If there.is any glazing on the pads or rotors your performance will be sub par. Good luck

Thanks B RON CO, the pads I think are a possible issue. I just need to figure out what pads to get now. I've heard semi-metallic stop best but ceramic with copper embedded are softer.
 

NicksTrix

Bronco Guru
Joined
Aug 1, 2001
Messages
6,410
Go check out the brake man. They aren't far from you
They make some great pads & pieces
I'm sure willwood has some aggressive compounds you could try
 

nickgp

Bronco Guru
Joined
Jan 17, 2010
Messages
1,024
We put hydro boost on our 66 WITH drum brakes all the way around( discs up front are to be installed). I can't believe how well the damn thing stops! Guess I'll have to thing back about my auto shop teacher praising drum brakes!
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,651
Hey Bukin, what size tires are you running on those 15's? More and more it seems that by the time you go over 33 inches the vacuum type boosters are just not sufficient to really get your whoa on.

As said, the smaller bore master will give you more power-per-pound of foot pressure. But at the expense of slightly more pedal travel to get the job done.
I can't say about the dual bleeders, but I would certainly call Wilwood on that. Anytime I see two bleeders I say they're there for a reason. Yes, maybe it's just so you can more easily bleed them with the wheels still installed on either side without having specific left and right calipers, but maybe it's more than that in this case. Well worth a quick call I would say.
Personally, I would think that both need to be bled as you can have air pockets anywhere there's a high point.

Is your proportioning valve fully open? If you can't lock anything up, you certainly don't need it subtracting any power to the rear brakes. It's only to keep from locking up, so if you can't remove it easily enough, just make sure it's all the way open.

Good luck. Let us know what Wilwood says about it.
I wonder if they have that info on their site?

Paul
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,651
Oh, and just how vertical are the bleeders?
If not straight up, they say you should remove the caliper for bleeding so you can hold it vertically.

Paul
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,651
Confirmed:
Bleed outermost screw first, then move to the inner. Then move on to the next caliper and do the same.
It's the same pattern, as in furthest from the master first. This includes BOTH bleeders.

Paul
 
OP
OP
Bukin 67

Bukin 67

Bronco Abuser
Joined
Jul 3, 2008
Messages
2,268
Confirmed:
Bleed outermost screw first, then move to the inner. Then move on to the next caliper and do the same.
It's the same pattern, as in furthest from the master first. This includes BOTH bleeders.

Paul

Thanks Paul. I don't know why I didn't pick that up! I'll try that first.
I'm running 35x12.5 tires
Thanks, Randy

TheBrake Man is on the list too Nick, thanks for the info
 

Rustytruck

Bronco Guru
Joined
Feb 24, 2002
Messages
10,872
If you bleed the calipers off the rotor put a block of wood between the pads. Are you running steel braided brake lines instead of rubber lines? You will get slightly better response with braided lines and much better if your removing old rubber lines.

Hydro boost brakes should not tax your power steering pump as there is no real volume used through the actuator. Nothing like your power steering ram.
 

broncnaz

Bronco Guru
Joined
May 22, 2003
Messages
24,342
Id get all your specs together there are calculators and guidelines on caliper piston area vs MC piston size. Just a quick look and Id say 1 1/8" is to big. 1in or 15/16" may be what you need but I don't know what your total piston area is. but going down to a 1in MC will give about another 300 psi to the calipers.
Most of the time the more pistons you have in a caliper the less piston area you have especially for a given rotor size.. So going to 4 piston calipers may reduce braking even more.
Either way you still may be hard pressed (pun intended) to get 35's to lock up. I think it may be doeable but the system has to be matched to get as much out of it as you can.
 

68ford

Bronco Guru
Joined
Dec 26, 2004
Messages
2,710
My eb built to do the same as yours and weighs over 5000 and same 15in wheels and 35s. I run 6piston wilwoods in the front and 4 piston supelites in the rear. Rear rotors are custom diamter since I have a floater housing. They are as big as possible, I belive 12.5. I do not have any power assist, but I have a dual master cnc pedal assembly with slightly more leverage than stock eb pedal. Master are 3/4 front and 7/8 rear. It stops amazing, very very little effort even in a panic stop. Pedal travel little more than normal but price you pay for no assist. Brakes work so good when I let people drive it, I don't bother to tell them it has no power brakes or that they will have to push harder than a normal car.
 
OP
OP
Bukin 67

Bukin 67

Bronco Abuser
Joined
Jul 3, 2008
Messages
2,268
Id get all your specs together there are calculators and guidelines on caliper piston area vs MC piston size. Just a quick look and Id say 1 1/8" is to big. 1in or 15/16" may be what you need but I don't know what your total piston area is. but going down to a 1in MC will give about another 300 psi to the calipers.
Most of the time the more pistons you have in a caliper the less piston area you have especially for a given rotor size.. So going to 4 piston calipers may reduce braking even more.
Either way you still may be hard pressed (pun intended) to get 35's to lock up. I think it may be doeable but the system has to be matched to get as much out of it as you can.

Thanks for the imput. I bled the brakes today and still have issues, so,it looks like it's pretty much a do-over at this point.
 
OP
OP
Bukin 67

Bukin 67

Bronco Abuser
Joined
Jul 3, 2008
Messages
2,268
My eb built to do the same as yours and weighs over 5000 and same 15in wheels and 35s. I run 6piston wilwoods in the front and 4 piston supelites in the rear. Rear rotors are custom diamter since I have a floater housing. They are as big as possible, I belive 12.5. I do not have any power assist, but I have a dual master cnc pedal assembly with slightly more leverage than stock eb pedal. Master are 3/4 front and 7/8 rear. It stops amazing, very very little effort even in a panic stop. Pedal travel little more than normal but price you pay for no assist. Brakes work so good when I let people drive it, I don't bother to tell them it has no power brakes or that they will have to push harder than a normal car.

Hi 68, I'm either going long pedal or electric at this point but in any case the vacuum setup is out.

I discussed long pedal with my fabricator a few months ago and we started looking at the feasibility of going that route. It would actually be less costly, and I could sell the vacuum system since it's practically new. Thanks again for your info.
 

68ford

Bronco Guru
Joined
Dec 26, 2004
Messages
2,710
Hi 68, I'm either going long pedal or electric at this point but in any case the vacuum setup is out.

I discussed long pedal with my fabricator a few months ago and we started looking at the feasibility of going that route. It would actually be less costly, and I could sell the vacuum system since it's practically new. Thanks again for your info.

if you do a dual master set up like mine, it takes up almost no room I
outside the firewall. plus if you down in piston diameter you don't a really long pedal.
 
Top