• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Rear spring shim question

BRONCITIS74

Full Member
Joined
Oct 4, 2015
Messages
340
Doing a 3 1/2 lift on my 74. When I get to the rear springs, would it be a good idea to use the tapered shims under them? What degree (4 or 6) do you guys suggest? I figure it would be easy to do while its all apart, rather than have to do it later. Thanks for any suggestion and advice. Mike
 

Doyle

Bronco Guru
Joined
Jun 12, 2006
Messages
1,026
My 73 with 3 1/2 inch springs took 6 degree shims, but as they say "results may vary".
 

66broncoCT

Contributor
Full Member
Joined
Feb 6, 2012
Messages
323
Loc.
Torrington, CT
I used 6° shims on mine when I added the 3.5" lift. You're right its easier to do now then after its all together but to get the measurement it has to be all together. Maybe give the guys at WildHorses a call or pm dirtdonk (paul) on here and see what they say.
 

SHX669

Bronco Guru
Joined
Jan 9, 2009
Messages
1,997
I put 6* shims in both my broncos with 3 1/2" lift. It helped the u joint angle.
 

bronconut73

Bronco Guru
Joined
Aug 7, 2012
Messages
9,919
I definitely needed the 6° shims when I put my 2.5", WH, 11 leaf? packs in. But they have settled down a little more than I expected, not complaining, as I love them. I could prolly go to a 4° now.
 

bronco loco

It never ends
Joined
Nov 12, 2005
Messages
2,735
Loc.
Long Island New York
When I installed the 2.5 WH 11 leaves pack spring, there was no need for shims. 3.5 leaves replacement gave me a vibration which 6 degree shims solved.
 

doghows72

Bronco Guru
Joined
Jan 5, 2005
Messages
2,036
Go with the 6*. I use them on my 2.5" lift because of the extra length with the 4R trans.
My pinion angle was at 12* before maybe even 13 put the 6* shim in and my angle went down to 3*.
If you don't have the extra length in your drive train and a 3.5" lift I would go 6*.
 

chriskent85

Full Member
Joined
Aug 17, 2016
Messages
293
Im gonna be installing the 3.5" extended radius arm lift from dufftuff. Should I go ahead and buy a set of 6* shims
 

jrwyant

Jr. Member
Joined
Jul 26, 2014
Messages
107
I went from 2.5" without shim and no vibration to 3.5" and a barely perceptible vibration that the 6 degree shim eliminated. No measurements, just added the shim and felt the improvement right away.
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,651
Are you guys actually measuring the angle, or is it just trial & error?
What is the pinion angle I'm trying to get?

Some measure, but the vast majority just wing it. If it vibrates (or you visually verify that the pinion angle is wrong) the shim gets added.
We only sell a 6 degree version because 95% of the time that's the one that does it.

I always recommend buying shims ahead of time. Whether you decide to install them before or not, at least they'll be on hand if you need them. And if not needed (still happens occasionally) just send them back for a refund.
With the thicker leaf packs, the need for shims with 2.5" of lift typically runs in the 50% to 60% range.
With the 3.5" lift heights, the percentage changes to more like 90% need the shims.
And it's very possible that some of the remaining rigs where the owner doesn't think they needed the shims actually does. They just don't notice the subtle vibration with more aggressive tires.

The angle you're looking for is approximately 2° down-bubble. So the pinion shaft points just below the centerline of the driveshaft by 2 degrees.
A 1 to 3 degree setting is probably workable, but 3 is pushing it so most shoot for 2 instead.

This is all assuming a stock type double-cardan style shaft of course.

Paul
 

1971lubr

Sr. Member
Joined
Mar 23, 2014
Messages
534
Loc.
Cape Coral, FL
So driving mine after installing 2.5" deaver 11 pack springs I have almost a hop at 30 mph in 3rd. Nothing under acceleration, I'm guessing because of axle rolling. I wouldn't call this a vibration. I'm thinking I need shims? I haven't measured, but can easily see the pinion angle is off. Brand new everything under there. At first I thought the motor was missing, but idles and accelerates fine until rolling along in 3rd. Give it gas and it goes away. Haven't gotten above 30 yet because I'm still working out brake issues.
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,651
Odd time for it to happen when it doesn't happen anywhere else. Usually bad angles give more consistent clues.
But not every time I guess. Still good to verify before going to the trouble.

Does it happen right at the 2/3 shift, or just in third gear at that particular speed?
The going away when you give it gas is a good indicator of an angle too low, but you'd normally feel it more often when any kind of light throttle or decel is going on.
The happening only under one set of circumstances is odd. Not completely out of the realm of understanding perhaps, just odd.

Good luck. Post up your numbers when you're able to check.

Paul
 

Shulaps

Jr. Member
Joined
May 12, 2013
Messages
55
Loc.
BC Interior, Canada
I made my shims to custom fix my angle out of steel and tacked them in with the welder. 1/4 " plate with a 1/2" block under the rear end. Had to grind down the 1/2" a little bit to get it just right. Drilled a hole for the spring nut and welded it in. Worked perfect and is a little more solid than shims but less work than cutting off the spring hangers and re- welding. I put purchased aluminum shims in my previous eb and they were 6 degree and were a little too much.
 

ransil

Bronco Guru
Joined
Sep 6, 2003
Messages
8,138
So driving mine after installing 2.5" deaver 11 pack springs I have almost a hop at 30 mph in 3rd. Nothing under acceleration, I'm guessing because of axle rolling. I wouldn't call this a vibration. I'm thinking I need shims? I haven't measured, but can easily see the pinion angle is off. Brand new everything under there. At first I thought the motor was missing, but idles and accelerates fine until rolling along in 3rd. Give it gas and it goes away. Haven't gotten above 30 yet because I'm still working out brake issues.


I have a gopro , protractor & angle finder.

Brakes could be out of round drums.

as for shims, looks like some are guessing on here, I have used the Ruff stuff spring purches in the past to get the correct angle, if you have access to a welder it not that hard to get the old ones off and weld on the new ones.

http://www.wildhorses4x4.com/product/Anti-Wrap_Leaf_Spring_Perches/Bronco_Rear_Housing

http://www.ruffstuffspecialties.com/catalog/R1991.html
 
Top