• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Camber settings ?

JWMcCrary

Contributor
Bronco Guru
Joined
Oct 14, 2004
Messages
5,001
What are the specs for camber ? I wouldn't think it would but I'm using Duff's hybrid knuckles if that matters. Driving mine on the road more than I used to and notice the front tires are wearing faster than the rear and seem to have a pattern that would make me think they are leaning out at the top. I borrowed a Rebco caster/camber tool to check it.
 

broncodriver99

Bronco Guru
Joined
Jan 27, 2008
Messages
4,780
Loc.
Glen Allen, VA
I think originally it was around 1.5 degrees but that was for bias ply tires. Radials don't need much camber. I shimmed mine to about .5 degrees. You do want a little or it feels like you are driving on ice skates.
 
OP
OP
JWMcCrary

JWMcCrary

Contributor
Bronco Guru
Joined
Oct 14, 2004
Messages
5,001
1st pic is the right rear, 2nd pic is the right front. It could be toe-in, I haven't checked anything yet. Between the pic and looking at it from the front made me suspect camber......and don't ask me why, just one of those feelings.
 

Attachments

  • IMG_8229.jpg
    IMG_8229.jpg
    142.1 KB · Views: 87
  • IMG_8230.jpg
    IMG_8230.jpg
    150.4 KB · Views: 90
OP
OP
JWMcCrary

JWMcCrary

Contributor
Bronco Guru
Joined
Oct 14, 2004
Messages
5,001
couple pics from the front
 

Attachments

  • IMG_8243.jpg
    IMG_8243.jpg
    165.5 KB · Views: 127
  • IMG_8244.jpg
    IMG_8244.jpg
    167 KB · Views: 115

Yeller

Contributor
Bronco Guru
Joined
Mar 27, 2012
Messages
7,692
Loc.
Rogers County Oklahoma
for that much wear I'd suspect too much toe. Too much camber will wear the outside more but it shouldn't be accelerated. Mine has enough (never measured it) that you can actually see it. It does wear the outside of the tire more than the inside but they are not wearing faster than the rear over all. Also keep in mind swampers are notorious for not having the same wear characteristics from one tire to another, they build a great off road tire but not the best road tire. They are also sensitive to age, which can also effect wear rates, one tire may be 2 years old and another may be 5 which they will have different wear rates.

Keep driving it, its fun:) mine's in the parking lot today
 
OP
OP
JWMcCrary

JWMcCrary

Contributor
Bronco Guru
Joined
Oct 14, 2004
Messages
5,001
These tires are almost 8 years old. Plan to change them out in a couple months, thought I might fix at this issue before new ones. Never been rotated and don't drive it enough that it should really matter. But if there is something obviously off in the front end and can be fixed or made better easily....then why not. I'm off Friday and plan to investigate.
 

dholder

Full Member
Joined
May 24, 2012
Messages
227
I have 35's all terrain T/A, and they became worn like yours in a very short time. I eyeballed mine as well, and they looked about like yours as far as camber goes, tilted out at the top. I installed the largest adjustable upper ball joints and the largest spindle shims and have mine down to about 1/2 degree of camber. That is the lowest I can get out of mine.
 

Yeller

Contributor
Bronco Guru
Joined
Mar 27, 2012
Messages
7,692
Loc.
Rogers County Oklahoma
These tires are almost 8 years old. Plan to change them out in a couple months, thought I might fix at this issue before new ones. Never been rotated and don't drive it enough that it should really matter. But if there is something obviously off in the front end and can be fixed or made better easily....then why not. I'm off Friday and plan to investigate.

I'm betting a good alignment will take care of most of that. These old trucks are pretty simple, if you can just find an alignment tech that can read a machine, interpret what its saying and turn that into fixing it. And in truth with a tape measure will do most of it
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,651
Original spec was 1 to 2 degrees positive camber. With the 1.5 degrees broncodriver mentioned being considered the optimal setting. But what the others have said is all true. These things seem to work better with less than 1 degree. Getting it down to a half to a quarter degree seems to be a sweet spot.

Caster was 2.75 to 3.25 in the early years, 4 to 6 later when power steering was ubiquitous. It's a pretty rare '75 or earlier EB however, that can achieve that with normal methods. Probably didn't even have it from the factory. Cut-n-Turn is the only solution for the worst offenders.
Full-size Broncos got 6 to 8 if I remember correctly.
If you're still running manual steering, your options are fewer. But if you do have a good power setup already, try to get 4.5 to 6 degrees positive caster if you can. Really anything over 3.5 on an EB is a coup if you can achieve it!

Toe-in seems to follow factory recommendations for most of us, at between 1/16 to 1/4 inch. With 1/8" being optimal. That's worked for me with every tire/wheel combo I've had.
However, there are a few running "toe-out" settings now, which also seem to be having good luck with it. Can't remember exact numbers at the moment, but there was a discussion about it last month I think it was.

Offset ball-joint collars, tapered spindle shims, C-bushings and radius arm drop brackets are the most common ways of getting caster, camber or both. Many of us run multiples of those, and even a few all-of-the-aboves running around.
When trying to correct caster you still have to be mindful of the pinion angle and not biding up the front u-joint.

I know you were talking about camber only, but I figured it was good to put all the categories on the table while you're messing about with yours.

Good luck.

Paul
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,651
...I wouldn't think it would but I'm using Duff's hybrid knuckles if that matters.

You're right that it should not matter. Pretty sure the Duff knuckles are based off of the Ford specifications, BUT, knuckles can indeed make a difference.
Depending on how a particular one is designed and manufactured could have a direct effect on camber at least, and caster as well.

But getting a readout with your gauge, and maybe even a full printout from a shop so you know what your current settings are will be a good thing.

Let us know what you find out with yours.

Paul
 

Broncomt

Full Member
Joined
Oct 4, 2015
Messages
187
These tires are almost 8 years old. Plan to change them out in a couple months, thought I might fix at this issue before new ones. Never been rotated and don't drive it enough that it should really matter. But if there is something obviously off in the front end and can be fixed or made better easily....then why not. I'm off Friday and plan to investigate.

If you are going to have alignment checked, do it after new tires are put on. If aligned before it will be all off with new tires, especially so if they are different design. Then you have to spend the money all over again.
 

B RON CO

Contributor
Bronco Guru
Joined
Jun 29, 2016
Messages
2,484
Loc.
Statesville, NC
Hi, looks like a little toe out. Just an eyeball thing, from Saturday night stock car experience, where we run 3/16 toe out. From your whole front end shot it looks to me that your left wheel is pointing straight ahead and your right wheel is going ever so slightly to the right. It could be an optical illusion but I say it the way I see it. You could have some worn parts that let it settle that way. It is very easy to check toe and really the only setting you have any simple adjustments to make. As mentioned get the alignment done after the new tires. Good luck
 

blubuckaroo

Grease Monkey
Joined
Jun 11, 2007
Messages
11,796
Loc.
Ridgefield WA
Back when our '77 Bronco was still new, it had so much positive camber on the passenger side, that you could actually see it. The car came that way when we got it new. It ate tires like crazy!
I took it to a truck chassis shop. They put it on the alignment rack, chained it down and bent the tubes with a hydraulic jack. That's the proper way to fix it. Some use the eccentric ball joint nuts, but that can leave the ball torque incorectly adjusted.
 

Digger556

Sr. Member
Joined
Aug 8, 2013
Messages
801
What are the specs for camber ? I wouldn't think it would but I'm using Duff's hybrid knuckles if that matters. Driving mine on the road more than I used to and notice the front tires are wearing faster than the rear and seem to have a pattern that would make me think they are leaning out at the top. I borrowed a Rebco caster/camber tool to check it.


Specs for Camber are 1.50° from the factory. Most axles have held this if they don't have damage. That said, 1.5° is garbage for modern tires and will wear the outside edge of wider tires.


These are good basic specs with modern radial tires.
0.25° Camber
0.25° Toe In
3-5° Caster


If you want to be more advanced about it, you can split the front camber to achieve a left-pull-bias which will combat road crown and make the truck drive straight on most roads. I shoot for ~0.2° positive split to the driver's side, so my truck is set 0.3° Driver's / 0.1° Passenger's. The vehicle will pull to the side with more positive camber.

Additionally, if you have a wandering issue, add another 0.25° of toe in. People with large scrub radius' tend to dynamically toe out going down the road.



On to your specific issue, there is an easy way to distinguish between toe and camber wear: If the outside is worn evenly, you have too much positive camber. If the edge is "feathered" then you have a toe issue.

There is one other possibility to consider, even with perfect camber and toe settings, you can tear up the outside edge and see feathered wear if your Ackerman angle is not correct and you make lots of tight, near full-lock turns. I had this problem in college. I was running an EB44 on a 125" wheelbase Ranger and making tight turns into my apartment parking space everyday. It destroyed the tires and it looked like toe wear. I replaced the tires and moved to a house and never had an issue since.

Even switching to tie-rod over can screw with Ackerman geometry. Plus I'm not sure how good it was from the factory.
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,651
Back when our '77 Bronco was still new, it had so much positive camber on the passenger side, that you could actually see it. The car came that way when we got it new. It ate tires like crazy!...

I love telling the story of a friend (almost hate telling it actually!) who turned his Stroppe Baja Bronco back in to the dealer for the same reason.
He'd traded his plain '66 in on a '74(?) Baja, but unfortunately for him, nobody that he talked to (not sure if he tried an independent shop or not) could fix it and he didn't know how either, so he got his money back and bought a Suburban or something.
I was shocked when I heard that the first time because I was already a huge fan of the Baja. Oh well.
Glad you and your shop had the fix dialed in.

Paul
 

Bronco Junkie

So Cal Broncos
Joined
Feb 29, 2012
Messages
3,246
I did the alignment on my trail rig recently. The experienced alignment guy said he wanted 0.25 degrees camber...and that is what I have. Needed shims to get it.
 
Top