• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Suggestions on cooling a C4.. Update

Tiko433

Contributor
I know just enough to be dangerous
Joined
Jul 9, 2014
Messages
1,898
Loc.
Bolivia, North Carolina
I been running a Derale 15 row Atomic cooler but I had it ignition hot. When I did my swap I wired in the 180* thermo switch with a light so I could see when it switched on. It works as it should, it cuts on after about 20 min of driving. It does not cut off so either it's holding at 180* or it continues to get hotter. I don't like using the cooler in the radiator, I had one fail and trash a transmission before. I'm hooking a temp gauge and a and slack plate cooler, I'm going to put the new cooler before it goes into the Derale.
What is a good temp range for a C4?
I never thought about it before I had that light telling me it hit 180*
This is all after my swap and new exhaust, the pipe that crosses under the transmission is right under the lowest part of the bell housing. It's not touching, a BFH made sure of that but it about a 1/4 in away. I also put header wrap on it to help. I will know more when I install the gauge but suspect that pipe is not helping at all.
 
Last edited:

Eoth

Bronco Guru
Joined
Mar 10, 2004
Messages
1,692
175 is normal temp and your fluid will be happy and will last 100,000 miles. As a rule of thumb, every 20 degree increase in operating temperature above 175 degrees cuts the life of the fluid in half. At 195 degrees F., for instance, fluid life is reduced to 50,000 miles. At 220 degrees, which is commonly encountered in many transmissions, the fluid is only good for about 25,000 miles. At 240 degrees F, the fluid won't go much over 10,000 miles. Add another 20 degrees, and life expectancy drops to 5,000 miles. Go to 295 or 300 degrees F., and 1,000 to 1,500 miles is about all you'll get before the transmission burns up. Bad fluid = bad trans.... At 250 degs damage to seals will occur even if your fluid is good.
 

Broncobowsher

Contributor
Total hack
Joined
Jun 4, 2002
Messages
37,111
What gears are you running and what size tires. That affects the loading on the torque convertor and that reflects the heat it is creating.

The in radiator cooler is highly effective for the small size that it is. It has been the standard cooler for 50+ years in nearly every production car. There is good reason for this. The oil to air cooler is a helper, optional in many cases. And now asking to do all cooling. That's hard.
 

KyleQ

Bronco Guru
Joined
Apr 24, 2008
Messages
5,480
I gave up on those 180* thermostat units on both of my installs, one for PS and one for my trans. They just don't work like I want them to - I just leave both ignition hot now.

I use an 15 row Atomic Cool for my power steering and a 25 row Hyper-Cool for my trans.
 
OP
OP
Tiko433

Tiko433

Contributor
I know just enough to be dangerous
Joined
Jul 9, 2014
Messages
1,898
Loc.
Bolivia, North Carolina
Thanks guys Holly crap Eoth that is some scary information.
Broncobasher .., ( I will update my signature)
I'm running 33s and 3.50 gears . I rebuild the transmission last September and put a new TQ in it. It is a stock stall rate .
I'm not ruling out using the radiator cooler , if we're to use it What's the line routing ?
(Front outlet port) of trans -----radiator------cooler------back to trans(rear port)
I will know more when I mount the gauge. I have a deep aluminum Summit pan I'm going to tap it into it.
 

blubuckaroo

Grease Monkey
Joined
Jun 11, 2007
Messages
11,796
Loc.
Ridgefield WA
Yes, that little liquid cooled unit in the radiator has way better heat transfer capabilities than an air cooler. It would take an enormous air cooler to match it.
But sure, it's still a good idea to add an auxiliary cooler in series with it. Always put it in the return line to the tranny. That way you won't have the hotter tranny fluid the cooler in front of your radiator. Also, heat transfer is the best when the temperature differential is the highest.

Another thing I like to do with my C4 is to change the tranny fluid in the tranny pan every time I change the motor oil. It's really easy. The fill tube makes a great drain plug. The pan holds about two quarts. I don't bother with the filter since it's pretty much just a screen. This simple maintenance keeps the fluid red, the additives up, and the tranny happy.
 

KyleQ

Bronco Guru
Joined
Apr 24, 2008
Messages
5,480
This is how I keep my trans happy - running a deep pan to that filter to that giant cooler.

20170520_214745_zpsrognloy9.jpg
 

JohnJohn

Contributor
Bronco Guru
Joined
May 6, 2005
Messages
2,179
Loc.
Richmond
I also have the same problem and same 180* cooler switch but I am running 37" H1 wheels and 4.65 gears. I am going to visit my trans shop this week to get some ideas. I don't want to roast my newly rebuilt C4.
 

KyleQ

Bronco Guru
Joined
Apr 24, 2008
Messages
5,480
I also have the same problem and same 180* cooler switch but I am running 37" H1 wheels and 4.65 gears. I am going to visit my trans shop this week to get some ideas. I don't want to roast my newly rebuilt C4.

Same - I just leave the fan on all the time and it warms up a little when I'm beating on it (43's and 4.10 gears) and it cools off right away. I just don't trust the dang turn-on, I'd rather have an adjustable probe that controlled a relay that turned on the fan.
 

sanndmann3

Contributor
Bronco Guru
Joined
Jun 13, 2007
Messages
1,832
I'm running a F350 superduty trans cooler in front of my radiator. have an Autometer trans temp gage and 2 senders. one is coming out of the trans and the other just before it goes back in. use a switch to check hot and cool side.

Last trip to the dunes, the trans was running 160 deg. on hot side and 100 on the return. I'm currently adding a thermostat https://www.summitracing.com/parts/der-25719
to try and get the temp up to 180 or 190 so I'm not dumping so much heat in front of radiator...
 
OP
OP
Tiko433

Tiko433

Contributor
I know just enough to be dangerous
Joined
Jul 9, 2014
Messages
1,898
Loc.
Bolivia, North Carolina
Thanks for all the feedback guys. I'm going to get the gauge installed and see what Temps I'm actually seeing. I ordered a line kit today , I'm going to use the radiator cooler then into the Derale. I will be able to compare temps before using the radiator and using only the Derale .
 

ntsqd

heratic car camper
Joined
Jan 30, 2005
Messages
5,970
Loc.
Upper SoKA
Put the temp sensor in the trans pan. Putting it in the line only tells you the temperature of the oil in the line, not the temperature of the oil that the trans is pulling into itself for cooling and lubrication. I've been told that in a C4 the cooler line fluid is from the converter only, so that temperature is going to vary with load and not tell you anything about how the trans itself is doing.
Said differently, the fluid in the cooler system may or may not be the temperature of the fluid in the pan, and it is the pan fluid temperature that is most important.

I don't like putting the air to fluid cooler inline after the radiator. I put it before the radiator, and I size it to be able to do most/all of the cooling work. Then when the trans is working really hard the radiator cooler can help out, but when it's cold outside the radiator cooler actually helps get the trans up to operating temp faster, reducing wear on the trans. I don't care about abusing the fluid with thermal cycling, I care about the trans. The fluid is the service item and can easily be replaced. The trans, not so much. :eek:
I've posted this before and others disagree with it. That is fine. I've posted what I prefer to do and why, what you do with the info is up to you.

In a race rig, dedicated trails rig, or purely hot weather desert rig I'd probably do like above and use a liquid to air cooler with a fan on it and by-pass the radiator, but for a rig that is expected to be driven in all sorts of weather I want the trans to warm up too.
 
OP
OP
Tiko433

Tiko433

Contributor
I know just enough to be dangerous
Joined
Jul 9, 2014
Messages
1,898
Loc.
Bolivia, North Carolina
It's street rig, however it's driven to the beach and used to drive on the beach , its driven to where ever I take it off road so it needs to able to handle street traffic as well when I take it off road.
It will be interesting to see what temperatures I'm actually getting with the current set up. Maybe it's holding at 180-190 which would be ok, but if it's continuing to climb that's a problem and my current setup needs the be modified.
Funny how before I just had that cooler ignition hot and I didn't think much of it. But know that dam light is staring at me all I can think about is I'm cooking my trans. I don't even know how accurate that thermo switch is anyway. The switch is mounted right before it goes into cooler. I will put the temp sensor in the pan that should give me a good average
 

KyleQ

Bronco Guru
Joined
Apr 24, 2008
Messages
5,480
A road vehicle I would put the cooler before the radiator cooler and use the radiator to keep the fluid at the desired range. Your engine should always be around 180-190 and a fluid/fluid cooler works best, so then your trans would always be at that same range. Putting the cooler in front of the radiator would ensure you are consistently getting the temp that your coolant temp gauge reads.

I placed mine in the rear as I'm using a 4.0 Ranger radiator with a 450HP 357W and I wasn't sure that the radiator was even going to keep up, let alone add the heat of an automatic. Good news though, the radiator is more than enough with the Explorer mechanical fan, so I'm thinking I may add the radiator cooler into the mix, before my cooler though, there is a lot of hot under floor space the fluid has to go through before getting back to the filter and cooler, so I need it as cool as I can get it. The headers and exhaust will help heat the trans up just as fast as plumbing it through the radiator normally would anyway.
 

Broncobowsher

Contributor
Total hack
Joined
Jun 4, 2002
Messages
37,111
3.50 gears and 33s are going to be tough on transmission temps. That puts a lot of load on the convertor. Shorter tires or more gear will really help.

I would run the oil to air cooler first, to dump as much heat as possible before running it through the radiator for the final cooling. The oil to water cooler is on the cold tank of the radiator, so it will run cooler than engine temps (which are measured and thermostated on the hot side going to the radiator).

Line temps are pretty meaningless. Line out simply is showing how hard the convertor is working. Return line shows how good the cooler is working (which can read really low if there is a restriction in the line and the fluid is going through the cooler very slowly). But what matters is the fluid in the transmission. It is picked up by the pump and some of it goes to the convertor, and some of it goes to the clutches and lube. The part that goes to the clutches and lube is what matters. If you are not probing intermal passages, the pan is going to be nearly the same. Pan temp is the industery standard for monitoring transmission temps.
 

ntsqd

heratic car camper
Joined
Jan 30, 2005
Messages
5,970
Loc.
Upper SoKA
With the sensor right before the cooler all it's seeing is fluid coming out of the converter, which is consistently the hottest fluid in the trans. You may just be getting a false positive heat indication. Move the sensor before doing anything else, and drive it for a while before making any changes.

Rubber hose has its place in cooler lines, but using steel tubing for most of the cooler plumbing adds more heat rejection surface area. Could even put one of these in the cooler run from the trans: http://www.speedwaymotors.com/Aluminum-Heatsink-Transmission-Cooler-18-Inch,39873.html
91023118~2_L_16e26331.jpg


By itself I doubt it would be enough, but in combo with everything else it all adds up.
 

chuck

Bronco Guru
Joined
Aug 14, 2001
Messages
6,474
Loc.
Ingram, Texas
If you are running a stock stall speed convertor this will not help you but if you have a higher stall speed convertor and are driving below that speed the convertor will produce extra heat. We had a customer complain about engine and trans overheating and he thought he had a stock convertor but after checking found that he had a 2300rpm stall convertor and was driving below that RPM after changing it for a 700 rpm stall conv. all his heating problems left.
 

blubuckaroo

Grease Monkey
Joined
Jun 11, 2007
Messages
11,796
Loc.
Ridgefield WA
I guess if you're struggling with engine overheating, you might be tempted to run the fluid through the air cooler first. However, all the aux cooler vendors and cooling experts I've referenced recommend running through the radiator first. It has to do with the temperature differential and making the system work more efficiently.

You can read up on it if you want...

https://www.etrailer.com/question-40598.html
http://www.haydenauto.com/Installation-FAQs/Content.aspx
https://derale.com/images/stories/virtuemart/product/pdfs/13501.pdf
 
Top