• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Fuel Pressure on Carb?

moses_m

Full Member
Joined
May 5, 2013
Messages
262
Installed a holley truck avenger carb with a holley regulator. Starts fine and I have pressure when i start it 7 to 9 lbs. Once the engine is warm I lose all fuel pressure. Do i need a different regulator with a pressure relief back to tank. I have adjusted the float levels on carb like the directions state.

I have ran the carter fuel pump for years its the 4060 or 4070. Ran a eddlebrock. Trying out a holley for the larger sand dunes. The eddlebrock seams to bog from time. Its a regular street carb.

Going to run it today. See what it does on this warm day.
 

blubuckaroo

Grease Monkey
Joined
Jun 11, 2007
Messages
11,796
Loc.
Ridgefield WA
Electric fuel pumps aren't normally affected by vapor lock because they are typically mounted back close to the tank. Is yours mounted back there?
 

Rustytruck

Bronco Guru
Joined
Feb 24, 2002
Messages
10,872
Make sure the lines and clamps between the tank and pump are good and not sucking air. Make sure the tank is venting properly.
 
OP
OP
moses_m

moses_m

Full Member
Joined
May 5, 2013
Messages
262
TTT
I think i am good on volume. Running 3/8 fuel lines. Just ran it 80 mph 5 miles west then 5 miles back home. Got the temp up to 200 and it stayed there. Got home turned it off. Came right back on. Waited 15 more turned on no issues. Did not have to give it gas. Still no pressure on gauge. Took off gas cap did not hiss. Thoughts? Suggestions?
 

Broncobowsher

Contributor
Total hack
Joined
Jun 4, 2002
Messages
37,114
What fuel pump are you running right now? It isn't clear in your description.
 

Broncobowsher

Contributor
Total hack
Joined
Jun 4, 2002
Messages
37,114
My first though is a pin hole in the suction side of the pump. Old rubber hose. Amazing how much air can be sucked through such a small hole.

If you are suspecting the regulator, put the pressure gauge before the regulator. If it drops before the regulator, it isn't an issue with the regulator.

That carter pump should not need any bypass regulator.

And make sure you are not out of gas.
 

SHX669

Bronco Guru
Joined
Jan 9, 2009
Messages
1,997
Where do you have the regulator installed ?
And yes - are you using a tank that has fuel in it - I assume you have only one tank .
 

Rustytruck

Bronco Guru
Joined
Feb 24, 2002
Messages
10,872
Is your p4070 wired through an oil pressure switch or a rollover switch? Is it hooked up to an electric relay. When it shuts off is the pump motor hot? I would check all electrical connections for signs of heating up and loose connections
 

69_Sport

Full Member
Joined
Nov 5, 2014
Messages
286
That's a lot of pressure for a carb. I'd expect around 5psi or so. What does the manufacturer recommend?
 

mrdrnac

Contributor
Sr. Member
Joined
Feb 6, 2010
Messages
577
That's a lot of pressure for a carb. I'd expect around 5psi or so. What does the manufacturer recommend?

Agree! I run about 3-4 pounds maximum to my Holley truck avenger carb. I think the lower pressure may help prevent off angle flooding? Also saw that Holley said not to keep the pressure gauge permanently installed as failure of the gauge could result, don't know if you did or not just a thought?
 
OP
OP
moses_m

moses_m

Full Member
Joined
May 5, 2013
Messages
262
TTT
My issue is I am not getting fuel pressure at the gauge by the carb. Fuel tank is 3/4 full. I have the regulator, and fuel pump relay, bolted to the fire wall by the master cylinder. No oil switch installed. Going to bypass regulator first. Then going to run some new hose from pump to carb. Going to use AN fittings
 

Broncobowsher

Contributor
Total hack
Joined
Jun 4, 2002
Messages
37,114
I still want to know pressure before the regulator.
Diagnose the problem before throwing parts and changes at it.
 
OP
OP
moses_m

moses_m

Full Member
Joined
May 5, 2013
Messages
262
Bronco is running good. Just drove it round trip from Odessa TX to Yuma Arizona. 15hrs one way. Most of it at night driving. I have a air leak somewhere as the fuel pressure at carb works off and on. My question is Do I need a vented or a non vented gas cap?

Also looking for some suggestion on keeping the floor board cooler. Will start different thread on that one.
 

Bronco4x4

Sr. Member
Joined
Dec 21, 2009
Messages
621
What fuel lines and filter? I have the BCB lines and filter. I have same issue >> drives fine but pressure at carb was low. Only stalled once that raised the warning flag. It appears the BCB flared fuel line at filter outlet used an O-ring for some reason. My filter spun easy when checked. This was assembled in 2010 and I guess things loosened over time. There was no gas leak or smell. I put new fuel filter with same O-ring for now until the redo later. So far OK. The old filter was clean/perfect inside. So either the O-ring leaked air in or my rubber fuel line near tank may be collapsing (will redo if happens again). Need more drive time.
 
OP
OP
moses_m

moses_m

Full Member
Joined
May 5, 2013
Messages
262
TTT

My question is Do I need a vented or a non vented gas cap?
 
Top