• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Blown Head Gasket?

Smedley

Sr. Member
Joined
Feb 28, 2004
Messages
928
Loc.
Snohomish
Engine sat for 7 years during rebuild. Maybe had 15 or 20 thousand miles on it. I did not do anything to it other than clean and paint it. I replaced just about everything else, but not the damn engine. The video is from under the pside, where the head meets the block. The silver on the left is the exhaust manifold. Blown head gasket?

https://drive.google.com/open?id=1oQdDvvB1iuubrVbXmRXyrdZChQ_RSsEQ

Thanks,
Will
 

Timmy390

Contributor
Bronco Guru
Joined
Jan 1, 2011
Messages
5,948
Loc.
Conway, AR
Head gasket or the head is cracked...either way it's coming off. Once off you should be able to see the issue....

Tim
 
OP
OP
Smedley

Smedley

Sr. Member
Joined
Feb 28, 2004
Messages
928
Loc.
Snohomish
That’s what I figured. The kick in ass is that after a 7 year build I thought I would be driving it soon. At this point, with everything being new, I’m thinking about a new long block.
 
Last edited:

blubuckaroo

Grease Monkey
Joined
Jun 11, 2007
Messages
11,796
Loc.
Ridgefield WA
How much do you know about the rebuild?
It would be very difficult for me to put in a complete engine without taking it apart for a good inspection. And mileage would make no difference.
Sometimes you can only trust yourself.
 
OP
OP
Smedley

Smedley

Sr. Member
Joined
Feb 28, 2004
Messages
928
Loc.
Snohomish
I have never rebuilt and engine. I can turn a wrench but my engine knowledge is minimal.
 

suckerpunched

Sr. Member
Joined
Aug 24, 2006
Messages
882
I'm doing the same thing right now. Mine was a used engine that I did not tear down. I too am kicking myself. I wanted to drive up to Wildhorses round up but a couple days before I noticed a small puddle of coolant under the engine, next thing I know I am tearing the engine down. Heads are in the shop now getting checked for cracks and resurfaced.
 

Glass Pony

Contributor
Bronco Guru
Joined
Feb 13, 2012
Messages
1,954
Loc.
Sussex County Delaware
I went through the same thing a few years ago. My Bronco sat for 14 years during my restore with a remanufactured motor with 25,000 miles on it. After a couple years driving it after the restore I had a head gasket leak. When pulling the heads off I didn't think the head bolts were torqued enough. So I cleaned everything up got some new gaskets and a good set of head bolts (ARP) and she is good to go.
In hindsight I should have had the heads checked at a shop, but I guess I got lucky.
 

B RON CO

Contributor
Bronco Guru
Joined
Jun 29, 2016
Messages
2,484
Loc.
Statesville, NC
Hi, if that was my engine I would check the compression on all eight cylinders.
You want to see the condition of the engine. Evaluate what you have. If the compression is sketchy you have more work. If the compression is good I would just fix whats broken.
Next I would pull the valve covers and re torque the good side too see if any bolts were loose.
Then I would plan on changing the bad head gasket. Just the one side.
Good luck
 

Timmy390

Contributor
Bronco Guru
Joined
Jan 1, 2011
Messages
5,948
Loc.
Conway, AR
As stated, do a compression test and if everything is good but for the leak then pop the heads off, get them checked and reassemble with new head gaskets.

This can happen to new engines as well as old. I rebuilt my 351W only to have "bubbles" in the coolant. Long thread on it. After like 4 sets of head gaskets it turned out to be a cracked head the machine shop missed.

Tim
 
OP
OP
Smedley

Smedley

Sr. Member
Joined
Feb 28, 2004
Messages
928
Loc.
Snohomish
Thanks for all the feedback. I need to step back and figure out what next. I also noticed a leak at the back of the oil pan. Seems to be mainly when sitting, not running. So I need to track that down as well. Realistically, how much $$$ will I have into doing the head gasket job, if I do it myself? Just the gaskets? If I need to pull the motor to address the leak in the rear of the engine, would it just be worth my time and money to buy a new (reman) engine?

Thanks,
Will
 

Broncobowsher

Contributor
Total hack
Joined
Jun 4, 2002
Messages
37,114
7 years? was that with water in the cooling system? Can't watch the video (work security clamp down on external cloud storage crap).
Mud in the radiator could be excessive internal corrosion. Possibly to the point of compromising the head gasket.
I'll try and watch the video when I get home.
 

Glass Pony

Contributor
Bronco Guru
Joined
Feb 13, 2012
Messages
1,954
Loc.
Sussex County Delaware
I would check out the valve covers or the rear of the intake for the oil leak at the rear of the engine. Those would get replaced anyway if you do the head gaskets.
I guess it would be $100-$150 for head, intake, valve cover gaskets depending on what you get, plus the cost of fluids, anti freeze and oil. A good set of ARP head bolts for my 351w was $90. And then add the machine shop service cost.
How did the engine run before it sat?
 

Timmy390

Contributor
Bronco Guru
Joined
Jan 1, 2011
Messages
5,948
Loc.
Conway, AR
Thanks for all the feedback. I need to step back and figure out what next. I also noticed a leak at the back of the oil pan. Seems to be mainly when sitting, not running. So I need to track that down as well. Realistically, how much $$$ will I have into doing the head gasket job, if I do it myself? Just the gaskets? If I need to pull the motor to address the leak in the rear of the engine, would it just be worth my time and money to buy a new (reman) engine?

Thanks,
Will

Think I paid $20 each for the head gaskets. Heads checked and resurfaced at the machine shop was $75 each as I recall.

I've done head gaskets with the engine in and out. In the end it's about the same. If I had to choose, I would choose pulling the engine and putting it on a stand.

The "mud" is an issue. Sounds like tons of rust in the system.

Tim
 

pcf_mark

Bronco Guru
Joined
Jun 11, 2010
Messages
3,697
If there is anyone who can comment in head gaskets it is Timmy390! I followed his thread for weeks but he figured it out.

I would torque the head bolts again for fun to see if it stops. But I would also think that gasket is done either way. My guess is the engine had some water in it when it was stored or it got in while stored and just slowly rusted away the steel shim gasket. If I was going on the ultra cheap (which I would) I would take the head off and look at the block deck and the head deck. If they are flat with a straightedge I would simply clean up the gasket surfaces and put a new gasket on and re-use the old bolts. I have re-used 50 year old bolts on engines making a lot of power per cylinder. For less than $75 including gaskets and fluid you could be running. If it is cracked you are going to leak again and you are already thinking new long block why spend time or money on this engine beyond the minimum to try and save it?
 

blubuckaroo

Grease Monkey
Joined
Jun 11, 2007
Messages
11,796
Loc.
Ridgefield WA
Too bad about the leak, but replacing the head gaskets on one of these is about as easy as it gets. Especially if yours still has the positive stop rockers.
 

Timmy390

Contributor
Bronco Guru
Joined
Jan 1, 2011
Messages
5,948
Loc.
Conway, AR
If there is anyone who can comment in head gaskets it is Timmy390! I followed his thread for weeks but he figured it out.

I would torque the head bolts again for fun to see if it stops. But I would also think that gasket is done either way. My guess is the engine had some water in it when it was stored or it got in while stored and just slowly rusted away the steel shim gasket. If I was going on the ultra cheap (which I would) I would take the head off and look at the block deck and the head deck. If they are flat with a straightedge I would simply clean up the gasket surfaces and put a new gasket on and re-use the old bolts. I have re-used 50 year old bolts on engines making a lot of power per cylinder. For less than $75 including gaskets and fluid you could be running. If it is cracked you are going to leak again and you are already thinking new long block why spend time or money on this engine beyond the minimum to try and save it?

I still have night mares about it but did a head gasket since then and all was good so got my MO JO back.......:cool:

X 2 on the engine deck possibly being rusted. Something caused the issue and until you get the head off, you will not know the damage.

Tim
 

Thatbroncokid

Jr. Member
Joined
Mar 5, 2015
Messages
135
Loc.
BC Canda
Thanks for all the feedback. I need to step back and figure out what next. I also noticed a leak at the back of the oil pan. Seems to be mainly when sitting, not running. So I need to track that down as well. Realistically, how much $$$ will I have into doing the head gasket job, if I do it myself? Just the gaskets? If I need to pull the motor to address the leak in the rear of the engine, would it just be worth my time and money to buy a new (reman) engine?

Thanks,
Will

I have a similar leak at the back of my oil pan. Only leaks when i shut the truck off. 99% sure its my rear main. Mind you I only paid $500 for the motor, so im not exactly shocked haha. Do you have any oil dripping from the bottom of the bell housing? Thats a pretty good sign of a bad rear main.
 
OP
OP
Smedley

Smedley

Sr. Member
Joined
Feb 28, 2004
Messages
928
Loc.
Snohomish
Did a compression test on all cylinders today. 120 on all except 2 and 3, both got up to 110 then started losing pressure quickly down to 60. That is the same area I saw bubbling between the head and block. SO that seemed to confirm a blown head gasket. I pulled the head and was expecting a catastrophic blow out of the gasket. It looked fine. I’m not sure what a blown head gasket looks like but this seemed to have all of the symptoms of that, but the gasket looks intact. Thoughts?
 

Attachments

  • IMG_3056.jpg
    IMG_3056.jpg
    115.3 KB · Views: 156
  • IMG_3048.jpg
    IMG_3048.jpg
    134.8 KB · Views: 108
  • IMG_3050.jpg
    IMG_3050.jpg
    111.5 KB · Views: 153
  • IMG_3051.jpg
    IMG_3051.jpg
    89.7 KB · Views: 147
  • IMG_3052.jpg
    IMG_3052.jpg
    94.9 KB · Views: 122
  • IMG_3054.jpg
    IMG_3054.jpg
    88.8 KB · Views: 142
  • IMG_3055.jpg
    IMG_3055.jpg
    104.4 KB · Views: 149
Top