• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Gas gauge help

ruckin69

Contributor
Sr. Member
Joined
May 10, 2005
Messages
430
I am stumped on my gas gauge. Here is a diagram of what it looks like here is a picture of what I have. When I move my auxiliary sending unit up it puts my other tank gauge reading to empty. When I put it down it leaves the main tanks gauge reading where it is correct. So basically the aux sending unit is affecting the main sending unit and when I switch to aux on the switch it is not reading and stays on empty. I did a test light and it seems like the white and black wire on my gas gauge is blinking on and off is that normal but wiring colors seam correct? Where do I go from here? I'm trying to troubleshoot. Thanks.

Sent from my SM-G950U using Tapatalk
d75a57621f5d6ad725d206b2aab0ab9e.jpg
32c2e6c1a066b5519c426afa5b3ca344.jpg
ef37be6ad650739ea6eac250028d686b.jpg
51a44b5dfd93e1763b17ff169102078d.jpg
 
Last edited:
OP
OP
ruckin69

ruckin69

Contributor
Sr. Member
Joined
May 10, 2005
Messages
430
1 gauge with the main aux switch.
Dual tank.

Sent from my SM-G950U using Tapatalk
 

75MIKE

Sr. Member
Joined
Aug 22, 2001
Messages
991
Loc.
NE Washington
Are both tanks full of fuel? The main tank is the back one. Aux front if it has original wiring.

The switch should not be up and down, but side to side with the main on the left and aux on the right as the bezel sits.
 

Jebus

Full Member
Joined
Feb 13, 2011
Messages
303
Loc.
Longview, WA
I'm assuming the aux sending unit is out so you can raise and lower it?

The blinking on the white and black wire is the regulator, that it is connected to, regulating the voltage?, current? to the dash gauges.

I would start at grounds and check that tank gauge switch for leakage to another terminal.
 

oldiron

Bronco Guru
Joined
Jul 21, 2005
Messages
1,054
I'm assuming the aux sending unit is out so you can raise and lower it?

The blinking on the white and black wire is the regulator, that it is connected to, regulating the voltage?, current? to the dash gauges.

I would start at grounds and check that tank gauge switch for leakage to another terminal.

x2 on grounds. establish or verify.
 
OP
OP
ruckin69

ruckin69

Contributor
Sr. Member
Joined
May 10, 2005
Messages
430
Yes sending unit is out. Will do but Im am pretty sure grounds are good. So is that pulsing on the regulator normal?
 
OP
OP
ruckin69

ruckin69

Contributor
Sr. Member
Joined
May 10, 2005
Messages
430
Are both tanks full of fuel? The main tank is the back one. Aux front if it has original wiring.

The switch should not be up and down, but side to side with the main on the left and aux on the right as the bezel sits.
Rear 25 gallon has gas in it. Aux is out and sending unit is out. Switch it right.

Sent from my SM-G950U using Tapatalk
 

.94 OR

Contributor
Bronco Guru
Joined
Jul 5, 2009
Messages
2,215
Loc.
Willamette Valley, OR
When you first turn the key on and watch the fuel gauge, it sends the needle up in "pulses" instead of a continual sweep of the needle.

I'm dealing with mine too but my sending unit is in the tank so I need to check the ohm's to know if it is indeed setting on the bottom showing an empty tank.
 
Top