• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Considering a big block

gggpers

New Member
Joined
Feb 11, 2019
Messages
5
Loc.
Philly
Has anyone put a 390 into a 71 Bronco with success? I have a fresh 390 rebuilt one, bored and stroked to a 455. Edelbrock heads and intake. Looking to do something with it. I currently have a 6 cylinder in the Bronco. Just curious if it can be done with no major problems like engine fitment, and headers fitting as well.
 

Crush

Contributor
Bronco Guru
Joined
May 30, 2007
Messages
3,463
Loc.
Greenbottom, WV
that engine needs to go into a cobra reproduction, superformance or shelby!!!

i have an FMS 460 with aluminum cobra jet heads and rated at 560 hp waiting to go into something. this one was purchased back in about 98 and was one of the last they offered like this. the newer ones were 517 cubes or something like that it has been all i can do to keep from putting it in a 76 bronco i have:)
 

Broncobowsher

Contributor
Total hack
Joined
Jun 4, 2002
Messages
37,112
The FE has been done. So has just about any other engine made as well. Doesn't make it a good idea. No adaptors exist. No off the shelf headers will work. Cooling will be an issue, a small block is already hard to package a decent cooling system.

You would be better off finding a nice dent side F150 and drop it in there. Full size Ford car. I would say early mustang but those are not affordable anymore.

Just because you have the engine doesn't make it the right engine to use.
 

Scoop

Contributor
Bronco Old Fart
Joined
Feb 1, 2006
Messages
11,122
Loc.
Cuchara, CO
The FE has been done. So has just about any other engine made as well. Doesn't make it a good idea. No adaptors exist. No off the shelf headers will work. Cooling will be an issue, a small block is already hard to package a decent cooling system.

You would be better off finding a nice dent side F150 and drop it in there. Full size Ford car. I would say early mustang but those are not affordable anymore.

Just because you have the engine doesn't make it the right engine to use.

Or dent-side Bronco!
 

spap

Bronco Guru
Joined
Jan 2, 2010
Messages
2,642
Hey it’s your motor, but doesn’t an FE weigh about 650 pounds, and with all the cost of customs adapters couldn’t you build a healthy bored and stroked 351 to a 427 / 454 C3i that you can get parts for and put out some really good. Numbers
 

Apogee

Contributor
Bronco Guru
Joined
Nov 26, 2005
Messages
6,348
Loc.
Tangent, OR
That'd be a cool motor for a bunch of different applications, but an EB would be at or near the bottom of the list for me. Given the size, weight and logistics required to install in an EB, there's just too many compromises in doing so IMHO. Bronco Bob of All-4-Fun Off Road built the first 460 EFI powered EB I'd ever seen in person 20+ years ago, and it was a difficult swap by my standards. Cooling was a big issue, and the Volvo (IIRC) radiator ended up in front of the core support behind the grill due to a lack of space. Cooling for the C6 was also an issue, and there were fuel vapor lock issues as well that had to be sorted out. Bob fabbed up his own tubular exhaust manifolds as a solution to the header issue, but they would have definitely been a power limiter on something more than a stockish motor.

If I had that engine, I'd probably pull the 429 out of my '77 F150 and swap it in, then find a Torino or something to put the 429 into.
 

roundhouse

Bronco Guru
Joined
Sep 5, 2003
Messages
2,956
A stock 351W bolts right in and has plenty of torque and HP

Put the 390 in something else
Like a 66 Thunderbird convertible
 

bmc69

Contributor
Bronco Guru
Joined
Jun 11, 2004
Messages
12,015
I’ve wheeled with a guy that has a 390 powered EB. It does great.
 

PickleJar

Full Member
Joined
Nov 21, 2017
Messages
195
I would leave the six in there. Put that honker in something else, give you a reason to scoop up another toy...
 

Broncobowsher

Contributor
Total hack
Joined
Jun 4, 2002
Messages
37,112
I’ve wheeled with a guy that has a 390 powered EB. It does great.

I've wheeled with people that had a worn out 302, they wheel great as well. Just try and stay upwind of them.

The kind of wheeling that much power is useful the weight (and weight distribution) isn't useful.
 

Rustytruck

Bronco Guru
Joined
Feb 24, 2002
Messages
10,872
I knew someone who put in a big block and the truck would sink in the sand on the front end when running up washes, it really screws up the balance in the truck. way too front end heavy and totally screw up all the clearance in front of the motor. He had to butcher up the core support and mounted too small a radiator on the grill and had to go to hood pins to get the hood to close. He had to add body lift and in general butchered up the Bronco. He wasn't much of a fabricator and really ruined a decent bronco. he couldn't sell the thing afterwords. The money pit just got chopped up and sold as pieces.
 

Timmy390

Contributor
Bronco Guru
Joined
Jan 1, 2011
Messages
5,948
Loc.
Conway, AR
Has anyone put a 390 into a 71 Bronco with success? I have a fresh 390 rebuilt one, bored and stroked to a 455. Edelbrock heads and intake. Looking to do something with it. I currently have a 6 cylinder in the Bronco. Just curious if it can be done with no major problems like engine fitment, and headers fitting as well.

That's a BIG 390FE.....most will not bore enough. Most 455's start as 428 blocks as I recall. Would not shock me if it runs hot. The 390 in my 69 Stang is 40 over and that's as far as it can safely go. If you have a bigger than stock cam (and I'm sure you do) you better run end stands. Even the aftermarket rocker shafts will snap. Trust me I know :)

With the E-brock heads and intake it shouldn't weigh that much more than an all iron 351W.

Like said you will have to hack things up and get creative with headers. Cooling will be an issue.....if running a C6 then even more cooling issues.

I'm not saying don't do it. Love FE's but there are better options IMO and the cost will be less.

Tim
 
Last edited:

pcf_mark

Bronco Guru
Joined
Jun 11, 2010
Messages
3,697
Well since everybody threw sand in your shorts I'll go the other way. Sure it is heavy and it will run hot - but you have aluminum heads that will help both of these issues. I love cubic inches - the engine is just loafing along making 500 ft-lbs of torque. Easy to drive, fun to smoke the tires, extra fun to look at when you open the hood.

The cost may not make it worth it but I think that was covered above. This Bronco is the only small block equipped car I own that is from the muscle car era!
 

68ford

Bronco Guru
Joined
Dec 26, 2004
Messages
2,710
I too am in favor of this. As stated with alloy heads and intake it is not much heaver than a 351 with iron heads. Plus 100 more cubic inches all from stroke. Most 445 fe I have seen all made 550 to 625 foot pounds. As long as you do not have a huge bumper with a big winch, your front end will actually be lighter than most. I say ditch the battery to the rear and make what ever mods are required to run a wider radiator.
Oil pan will be the toughest part.
 

fordguy

Contributor
Bronco Guru
Joined
Jan 23, 2005
Messages
6,362
The older I get, the more I appreciate simple and closer to stock.
 

pcf_mark

Bronco Guru
Joined
Jun 11, 2010
Messages
3,697
I was thinking about this further and I think the exhaust manifolds or headers are going to be the bulk of the work after getting trans/4wd working. The passenger side will be the real problem you may not be able to find a manifold that fits the engine and will exit down and at the rear. Pickup perhaps? Or you are making a set of custom headers which is a 30-40 man hours of labor and best done with a big welder.

I think the path of least resistance and lowest cost is to use a 4R70W with an NP205 which we know fits in a Bronco and it pretty easy to do. Then you can use an adaptor bell housing to go from 4R70W to FE. That limits your adaptors to one bolt on piece.

[I should mention I have a 460 sitting in my shed]
 

Broncobowsher

Contributor
Total hack
Joined
Jun 4, 2002
Messages
37,112
That size engine, aluminum heads, not going to find a cast iron manifold anywhere close to usable. Good enough to allow the engine to idle and that is about it. Custom headers are a must. No off the shelf header will fit a Bronco chassis.
 

jckkys

Contributor
Bronco Guru
Joined
Mar 15, 2012
Messages
5,221
The original log type manifolds worked well. The street 427 Cobra was the fastest production car on the road at the time, with those manifolds. It also didn't have a real 427 medium riser engine. They had 428 PIs with a medium riser duel quad intake.
An aluminum intake is is the cheapest way to drop 50 lbs, from an FE. That makes it only 50 lbs. more than a 351W. All that being said The Gas Monkey redo of the Bullet '68 Mustang was inspirational. That's a far better home for a big inch FE.
 
Top