- Joined
- Oct 14, 2004
- Messages
- 5,001
This will be a little long but I think to help me you need you need to know some history. I am running the Sniper 2V version on this Bronco, initial install was October of 2019. It was driven very little, just around the block a few times but it worked great and had power through all the gears. Fast forward to about a month ago and while out on a ride with my granddaughter it started popping back thru the throttle body. Found out a valve lifter had come apart. With this engine being old with almost 0 oil pressure at idle, I decided to change engines. I have a rebuilt 302 that had been run very little when I bought it, I bought the engine and trans from a guy doing a 4BT swap. This was in 2007, engine had sat since then. I tore it down to long block and it was clean as whistle on the inside. I have all the specs from the build, new pistons, bearings, rings, etc, new crankshaft, comp cams RV cam, double roller timing chain and gear, double valve springs on the heads, heads are 289 heads that had been reworked. I resealed the engine and painted. I decided to add the explorer front dress while doing the swap so it got a new water pump. I put in a 4 core 5.0 aluminum conversion radiator. Put in a new HEI distributor, I damaged the coil on the old one it was already running, after looking at a coil, cap, rotor for a few more dollars I just replaced the whole thing and keep the old one as a spare. I'm not controlling timing with the Sniper, it's using the coil connection on the HEI for tach signal. Running stock exhaust manifolds with a single muffler which is 2 in and 2 out. Got it all together, did new wizard calibration on the sniper and fired it up. It runs great. Let it get up to temp, has 180 thermostat and idles at around 180-185. Played with the timing and 12 degrees seems to be the sweet spot by ear. Verified that the distributor was advancing the timing.
A big difference now compared to before is the IAC whistles like crazy, very loud until it settles in between 0-10. Fuel pressure is good and have plenty of fuel. Go for test drive and as soon as it gets out of granny low it bogs like crazy, no power at all. Have to play with the accelerator to get it back running smooth. As long as you stay in a lower gear, granny or first it will pull with a little power but past that it's fluttering and stalling. OK, the tires are too big for the gear, but it didn't do this with a wore out engine. Something obviously isn't right, and I don't know what it is. It also runs hot on a less than 2 mile test drive, jumps up gradually to 220 before I'm back to the driveway, let it idle and the temp comes back down where its supposed to be. I verified that coolant is circulating thru the system. Did this by starting it up cold with the cap off and watching it until the thermostat opens and you can see coolant moving.
I changed the IAC motor this morning and that made no change with the whistling, I'm told this can be common. When it starts running bad on test drive the IAC also starts whistling. I changed out the Ford spacer between the throttle body and intake with a new aluminum spacer and thick gaskets to ensure no leaks.. Idling all the specs are within what the book tells you they are supposed to be. I'm leaning towards changing the oxygen sensor, the old one was black with soot from the old engine. I hate just throwing part at it to fix it and I think the issue is likely simple (hopefully). It runs too good at idle to be a big issue. It starts instantly.
Anybody have any thoughts or suggestions based on what I describe above?
God bless you if you read all the way through that.
I'm headed out of town for a few days, do me good to clear my head of this thing for a while.
I posted over on Holley forum, those guys talk above my level most of the time. Almost always want you to pull a datalog, which I'm sure helps if you know how to read it. Hoping some experience here might help before I dive into that.
A big difference now compared to before is the IAC whistles like crazy, very loud until it settles in between 0-10. Fuel pressure is good and have plenty of fuel. Go for test drive and as soon as it gets out of granny low it bogs like crazy, no power at all. Have to play with the accelerator to get it back running smooth. As long as you stay in a lower gear, granny or first it will pull with a little power but past that it's fluttering and stalling. OK, the tires are too big for the gear, but it didn't do this with a wore out engine. Something obviously isn't right, and I don't know what it is. It also runs hot on a less than 2 mile test drive, jumps up gradually to 220 before I'm back to the driveway, let it idle and the temp comes back down where its supposed to be. I verified that coolant is circulating thru the system. Did this by starting it up cold with the cap off and watching it until the thermostat opens and you can see coolant moving.
I changed the IAC motor this morning and that made no change with the whistling, I'm told this can be common. When it starts running bad on test drive the IAC also starts whistling. I changed out the Ford spacer between the throttle body and intake with a new aluminum spacer and thick gaskets to ensure no leaks.. Idling all the specs are within what the book tells you they are supposed to be. I'm leaning towards changing the oxygen sensor, the old one was black with soot from the old engine. I hate just throwing part at it to fix it and I think the issue is likely simple (hopefully). It runs too good at idle to be a big issue. It starts instantly.
Anybody have any thoughts or suggestions based on what I describe above?
God bless you if you read all the way through that.
I'm headed out of town for a few days, do me good to clear my head of this thing for a while.
I posted over on Holley forum, those guys talk above my level most of the time. Almost always want you to pull a datalog, which I'm sure helps if you know how to read it. Hoping some experience here might help before I dive into that.











