• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Sniper Problems - Need some help

JWMcCrary

Contributor
Bronco Guru
Joined
Oct 14, 2004
Messages
5,001
This will be a little long but I think to help me you need you need to know some history. I am running the Sniper 2V version on this Bronco, initial install was October of 2019. It was driven very little, just around the block a few times but it worked great and had power through all the gears. Fast forward to about a month ago and while out on a ride with my granddaughter it started popping back thru the throttle body. Found out a valve lifter had come apart. With this engine being old with almost 0 oil pressure at idle, I decided to change engines. I have a rebuilt 302 that had been run very little when I bought it, I bought the engine and trans from a guy doing a 4BT swap. This was in 2007, engine had sat since then. I tore it down to long block and it was clean as whistle on the inside. I have all the specs from the build, new pistons, bearings, rings, etc, new crankshaft, comp cams RV cam, double roller timing chain and gear, double valve springs on the heads, heads are 289 heads that had been reworked. I resealed the engine and painted. I decided to add the explorer front dress while doing the swap so it got a new water pump. I put in a 4 core 5.0 aluminum conversion radiator. Put in a new HEI distributor, I damaged the coil on the old one it was already running, after looking at a coil, cap, rotor for a few more dollars I just replaced the whole thing and keep the old one as a spare. I'm not controlling timing with the Sniper, it's using the coil connection on the HEI for tach signal. Running stock exhaust manifolds with a single muffler which is 2 in and 2 out. Got it all together, did new wizard calibration on the sniper and fired it up. It runs great. Let it get up to temp, has 180 thermostat and idles at around 180-185. Played with the timing and 12 degrees seems to be the sweet spot by ear. Verified that the distributor was advancing the timing.
A big difference now compared to before is the IAC whistles like crazy, very loud until it settles in between 0-10. Fuel pressure is good and have plenty of fuel. Go for test drive and as soon as it gets out of granny low it bogs like crazy, no power at all. Have to play with the accelerator to get it back running smooth. As long as you stay in a lower gear, granny or first it will pull with a little power but past that it's fluttering and stalling. OK, the tires are too big for the gear, but it didn't do this with a wore out engine. Something obviously isn't right, and I don't know what it is. It also runs hot on a less than 2 mile test drive, jumps up gradually to 220 before I'm back to the driveway, let it idle and the temp comes back down where its supposed to be. I verified that coolant is circulating thru the system. Did this by starting it up cold with the cap off and watching it until the thermostat opens and you can see coolant moving.
I changed the IAC motor this morning and that made no change with the whistling, I'm told this can be common. When it starts running bad on test drive the IAC also starts whistling. I changed out the Ford spacer between the throttle body and intake with a new aluminum spacer and thick gaskets to ensure no leaks.. Idling all the specs are within what the book tells you they are supposed to be. I'm leaning towards changing the oxygen sensor, the old one was black with soot from the old engine. I hate just throwing part at it to fix it and I think the issue is likely simple (hopefully). It runs too good at idle to be a big issue. It starts instantly.
Anybody have any thoughts or suggestions based on what I describe above?
God bless you if you read all the way through that.
I'm headed out of town for a few days, do me good to clear my head of this thing for a while.

I posted over on Holley forum, those guys talk above my level most of the time. Almost always want you to pull a datalog, which I'm sure helps if you know how to read it. Hoping some experience here might help before I dive into that.
 

Broncobowsher

Contributor
Total hack
Joined
Jun 4, 2002
Messages
37,114
Couple things I think of.
Do you have all the plug wires in the right place. Since there are 2 different firing orders for a small block depending on which cam is used. This has happened a lot, I am even guilty of it (more than once).

The other, with the heads freshly installed, head gasket installed backwards. There is print on them "FRONT" but often people will install them with the same side up which puts a "FRONT" at the back of the engine. That screws with water flow. Many gaskets have an external tab so you can tell without taking the heads off.
 
OP
OP
JWMcCrary

JWMcCrary

Contributor
Bronco Guru
Joined
Oct 14, 2004
Messages
5,001
Yes, it's wired correctly, very confident the cam is 15426378

Heads were not off, I stripped it down to the long block. Removed pan, front cover, etc. This was a running engine in a bronco that had just been rebuilt by Plano Machine in Plano Tx. I can't find it right now but I had the list of everything that was done to it. I have confidence in the motor. It idles with 25lbs of oil pressure after warmed up. Giving it throttle from idle it sounds very healthy. But it's running bad before the temp goes up. Wondering if the oxygen sensor is bad and the fuel is way off under load that might contribute to the heating issue.
 

hammer189

Full Member
Joined
Jan 13, 2013
Messages
339
Loc.
South Atlanta
Do you have a fan shroud on the radiator? Very important. My 5.0L runs 196-204 with a 195 thermostat. Can’t help with the sniper. Sorry.
 
OP
OP
JWMcCrary

JWMcCrary

Contributor
Bronco Guru
Joined
Oct 14, 2004
Messages
5,001
Do you have a fan shroud on the radiator? Very important. My 5.0L runs 196-204 with a 195 thermostat. Can’t help with the sniper. Sorry.

Yes, I think the heat is related to the running issue. That's the only reason I brought up the temp issue was in case it helped in diagnosing my problem
 
OP
OP
JWMcCrary

JWMcCrary

Contributor
Bronco Guru
Joined
Oct 14, 2004
Messages
5,001
Problem solved.....and it was simple.

With this engine swap I upgraded to explorer front dress, this moves the timing pointer to the passenger side. I had a pro street balancer that has multiple timing marks that could be easily changed between 28 & 50 oz by changing the weight. I decided to use this balancer with a 28oz weight and the crank pulley that WH sells for serp. When I dropped in the distributor I did old school with my finger over number 1 hole until I had compression, looked at the balancer and moved it to 0. Started it from that point and adjusted timing based on that install.
I had a problem with the flowkooler water pump impeller rubbing bad on the back of the pump, this was due to me pressing the pulley on further until it wasn't against the front cover and would turn. Was hoping it was Ok but it wasn't so I decided to change the water pump. While the water pump was off and I had good access to the balancer I decided to use a piston stop and verify TDC. I could use my ear and move timing to where it sounded better but checked with a light it showed way too far advanced at idle....obviously something is off. Went through the procedure using the piston stop and marked the balancer and it was way off 0 on the timing marks I was using. I took some sand paper and cleaned the balancer and there it was, another set of timing marks on the back of the balancer that I couldn't see previously. And TDC was dead on 0 using those marks. I put a timing tape on to where I could see it with a light, fired it up, moved timing to 10. Runs great, will take off in 3rd gear, loads of power.
Lesson learned....verify TDC. The timing marks I used were close enough that ot would run, and actually idle pretty good, but the timing was retarded .
 
Top