• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Head/Valve Question?

green61bug

Contributor
Bronco Guru
Joined
Mar 25, 2018
Messages
1,116
Loc.
Greensboro
I just posted this in my build thread but I might get a few more responses outside of that and I apologize for any repetitiveness.

I recently rebuilt my carb and adjusted it by ear to what I felt was pretty close. It ran good however the choke wasn't right and I just wasn't sure how accurate I got it so I asked a buddy to check it and set the choke up for me. I drove it over last night and when I cranked it he asked why my valves were so loud and proceeded to try and adjust them. They weren't bogging down or getting any quieter. Upon further inspection we noticed that the rocker is actually hitting the retainer on top of the spring which is why it is causing so much noise and not allowing for adjustment. I'm not really sure what is going on here and could use a little advice.The guy that assembled my heads obviously knew there was a problem because he ground on the rockers to try and clearance them. My buddy said he asked his local machine shop what they thought might be going on and they said probably the wrong valves? Check out the pics and let me know if you have any ideas.
 

Attachments

  • Motor_001.jpg
    Motor_001.jpg
    86.2 KB · Views: 150
  • Motor_002.jpg
    Motor_002.jpg
    80.6 KB · Views: 147
  • Motor_003.jpg
    Motor_003.jpg
    71.2 KB · Views: 148

JWMcCrary

Contributor
Bronco Guru
Joined
Oct 14, 2004
Messages
5,001
My guess is the wrong spring retainers. Never seen the rocker ground down for clearance before.
 

AZ73

Bronco Guru
Joined
Mar 28, 2012
Messages
3,813
There's any number of potential problems. Longer valves, shorter push rods, set up for roller but using stamped rockers, wrong cam, wrong hydraulic lifters. You should let us know what engine you have for starters. It's pathetic the engine builder tried to fix his mistake by grinding the rockers.
 

Broncobowsher

Contributor
Total hack
Joined
Jun 4, 2002
Messages
37,112
That is some machine shop shadieness right there. Mismatch of parts and instead of getting the right match of parts, start hacking away at stuff to get it out the door. They realized there was a problem. Just not capable of recoganizing what the real problem is. Instead they hacked at the symptom.

This gets into one of those ugly ones where you have to find a good machine shop that will spend some time and figure what is really going on. Which parts are incorrect and what will it take to correct them.

I really can't say what it will take to fix it. Can't tell where the hackery is at.
 
OP
OP
green61bug

green61bug

Contributor
Bronco Guru
Joined
Mar 25, 2018
Messages
1,116
Loc.
Greensboro

Attachments

  • Screen Shot 2021-02-17 at 1.32.02 PM.jpg
    Screen Shot 2021-02-17 at 1.32.02 PM.jpg
    114.1 KB · Views: 58
  • Screen Shot 2021-02-17 at 1.33.28 PM.jpg
    Screen Shot 2021-02-17 at 1.33.28 PM.jpg
    132.5 KB · Views: 62
  • Screen Shot 2021-02-17 at 1.35.17 PM.jpg
    Screen Shot 2021-02-17 at 1.35.17 PM.jpg
    90.8 KB · Views: 61
  • Machine_Shop_Receipt.jpg
    Machine_Shop_Receipt.jpg
    93.2 KB · Views: 64
OP
OP
green61bug

green61bug

Contributor
Bronco Guru
Joined
Mar 25, 2018
Messages
1,116
Loc.
Greensboro
So what I've gathered between my buddies information and facebook is that the valves are incorrect for the rockers. I should have a taller valve from the keeper up above the retainer... It's either change the rockers and probably have to add guides etc or change the valves? Does this sound accurate?
 

blubuckaroo

Grease Monkey
Joined
Jun 11, 2007
Messages
11,796
Loc.
Ridgefield WA
I think they've used the wrong push rods.
Check for proper push rods by marking the ends of the valve stem with a Sharpie and rotate the engine. The wear pattern should be centered on the end of the valve stem.
 

Broncobowsher

Contributor
Total hack
Joined
Jun 4, 2002
Messages
37,112
The old hot rod engine builders would bolt down a set of guideplates and use hardened pushrods with non-rail rockers. That can't be done as you still have the pressed in studs. So no place to bolt the guideplates in.

So you know the machine shop that did the work. Time to have a little talk with them about this matter and if they know how to address it. You never know, it might turn out good. I had a radiator that leaked, took it to a shop, rodded and resealed. Still leaked. Went back, they pulled the records, yea he no longer works here. Shop did right, discounts and credits back were liberally applied and there was suddenly a new core in the radiator.
 

Seventee

Contributor
Sr. Member
Joined
Dec 7, 2012
Messages
999
Loc.
In the sticks of MT
So what I've gathered between my buddies information and facebook is that the valves are incorrect for the rockers. I should have a taller valve from the keeper up above the retainer... It's either change the rockers and probably have to add guides etc or change the valves? Does this sound accurate?

I believe you are on the right track. I think the valves/retainers they used are made to be used with later model stamped-steel non-adjustable rockers. You are using adjustable rail rockers, which need additional valve stem clearance due to the rails. You cannot run the later model rockers, or roller tips with guideplates, so I think the only solution is to redo the valves. It's possible a different set of retainers could be used, but I don't know off the top of my head.

I'm shocked that a machine shop would pass this off as legitimate work. You absolutely need to talk to them about this.
 

AZ73

Bronco Guru
Joined
Mar 28, 2012
Messages
3,813
I believe you are on the right track. I think the valves/retainers they used are made to be used with later model stamped-steel non-adjustable rockers. You are using adjustable rail rockers, which need additional valve stem clearance due to the rails. You cannot run the later model rockers, or roller tips with guideplates, so I think the only solution is to redo the valves. It's possible a different set of retainers could be used, but I don't know off the top of my head.

I'm shocked that a machine shop would pass this off as legitimate work. You absolutely need to talk to them about this.

Ditto. It needs the correct valves and a new set of rockers. My guess is the old ground down rockers have wear in the wrong spot already.
 

EPB72

Contributor
Bronco Guru
Joined
Jul 13, 2019
Messages
1,216
Loc.
Pleasant Hill, CA
Rail style rocker arms required taller/extended valve stems,, those retainers look wrong as well ,, and looking like your valve train geometry is off push rods my be a little short ...I. An post a pic latter tonight as I have a set of heads sitting in my garage ..,,, either deal with your engine builder or find a machine shop that knows what there doing ,,, this sucks and is unfortunate,, It better you caught this then wait till it drops a valve !
 

69_Sport

Full Member
Joined
Nov 5, 2014
Messages
286
Talk to the machine shop. This is inexcusable. Did they think they solved the "problem" and you'd never find out? You're very patient. I'd have been down to "discuss" this with them by now over the barrel of my 12ga ...

Give them a chance to fix it correctly, and then if they refuse, use the internet for what it's best at - flaming their a$$e$!

Now I am thinking why would you want them anywhere near your engine again...
 

blubuckaroo

Grease Monkey
Joined
Jun 11, 2007
Messages
11,796
Loc.
Ridgefield WA
Rail style rocker arms required taller/extended valve stems,, those retainers look wrong as well ,, and looking like your valve train geometry is off push rods my be a little short ...I. An post a pic latter tonight as I have a set of heads sitting in my garage ..,,, either deal with your engine builder or find a machine shop that knows what there doing ,,, this sucks and is unfortunate,, It better you caught this then wait till it drops a valve !

I agree with this. The valve stems used on rail type rockers have more stem sticking out from the retainer.
https://www.stangnet.com/mustang-forums/threads/how-to-choose-rocker-arms.796848/
 

Rustytruck

Bronco Guru
Joined
Feb 24, 2002
Messages
10,872
bad to have the rockers hitting the retainers could have popped the keepers and dropped a valve into the cylinder. lash caps may help the situation but make the push rod problem even worse as the push rods are already short. note the adjustment bolts are really cranked down. a strange note you have a strange set of 302 heads as the studs should have a positive shoulder to stop the nuts. what year is the block? i suspect you may have the high deck low compression block which helps screw up the valve train if you don't know what to look for. they came about in 1974 or so. Right now its all a guess. either way its going to cost you to fix it right.
 

73azbronco

Contributor
Bronco Guru
Joined
Nov 11, 2007
Messages
8,782
Have to second the idea of wrong pushrods for the valve/spring rocker setup. A longer pushrod may solve the issue, maybe not. Whatever way, it sure looks wrong in first photo, that valve retainer shouldn't even be close to the rocker. May be moot as it may be the valves are to long for setup.
 
OP
OP
green61bug

green61bug

Contributor
Bronco Guru
Joined
Mar 25, 2018
Messages
1,116
Loc.
Greensboro
From what I have gathered between internet sources and my buddies machine shop(not the builder I used) is that the valve is out of a later model being short and for a different style rocker as many have mentioned. My buddy ground on the rockers enough to have them clearance without hitting the retainers. I know it isnt the right way to fix it and am hoping to get it done the right way before April but not sure if it is in the cards. The push rods measure about 6.8" and I have read that 1969 Flat tappet should have 6.9" push rods. Multiple have sais this should be enough to make a difference and I kind of agree but thought I hsee what yall have to say.
 

blubuckaroo

Grease Monkey
Joined
Jun 11, 2007
Messages
11,796
Loc.
Ridgefield WA
There are machine shops out there that are under the opinion that pushrod and valve length are fixed with a valve adjustment.
Don't go back to those shops.
 

73azbronco

Contributor
Bronco Guru
Joined
Nov 11, 2007
Messages
8,782
I am more concerned your guy said get to it later. No, they messed it up, they fix it now before doing someone elses work.
 

Seventee

Contributor
Sr. Member
Joined
Dec 7, 2012
Messages
999
Loc.
In the sticks of MT
From what I have gathered between internet sources and my buddies machine shop(not the builder I used) is that the valve is out of a later model being short and for a different style rocker as many have mentioned. My buddy ground on the rockers enough to have them clearance without hitting the retainers. I know it isnt the right way to fix it and am hoping to get it done the right way before April but not sure if it is in the cards. The push rods measure about 6.8" and I have read that 1969 Flat tappet should have 6.9" push rods. Multiple have sais this should be enough to make a difference and I kind of agree but thought I hsee what yall have to say.

Those rails are important to keep the rocker aligned on the valve tip. By grinding them down, they are now compromised and you risk more damage. You also risk knocking a valve retainer loose and dropping a valve into a cylinder. The pushrods are a secondary issue that will need to be resolved when the correct valve and rocker setup is in place.

I would not continue to run this engine without fixing the problems or it could get much more expensive real quick.
 
Top