• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Pcv/vent

68ford

Bronco Guru
Joined
Dec 26, 2004
Messages
2,710
I've seen setups similar to what you describe. What about doing the same thing from the valve cover at the rear on one side, have the oil filler on the opposite front side?
I currently run breathers in both, the problem is the breather is at an angle so there will always be some residue that leaks out the bottom side of the breather below the tube opening. If you had a tube that went into the valve cover and then angled to where the breather sat straight up would help with that. Haven't found such an animal but could be made i guess.

I just recently pulled my 395 that was built in 2005, I didn't run a PCV but it had started smoking under hard throttle, still ran great. I decided to build a new roller motor. When tearing down the 395 there was basically no wear in the cylinders, however when I took the heads (Edlebrock RPM Performer) to the machine shop for rework to go on the new engine it was found that every intake valve and guide was bad. These heads were bought new and bolted on, machine shop said the guides and the seats on the intake valves were out of alignment and is why they had worn so bad. I kept one of the valves and have it on my desk as a reminder to not just bolt on new parts without checking them out. That's where my oil was coming from. Nothing else I saw on this engine over 15 years not running a PCV concerned me.

You can run a hose from anywhere up to the air filter base. Just make sure there is enough hose that you can remove your air filter base without having to remove the hose if you care. Also try to not have any low points in the hose for oil to collect.
 

gr8scott

Contributor
Bronco Guru
Joined
Jul 1, 2011
Messages
1,890
I didn't know those existed until now. I just ordered a set for my new build. Those covers will put the breather in more of an upright position which will help with oil residue not getting trapped and leaking out. Be a while before I'm up and running though, couple months.

Thanks for the link.

Cool. Make sure you measure the holes when you get them in and make sure they weren't over-drilled like mine were.
 

Broncobowsher

Contributor
Total hack
Joined
Jun 4, 2002
Messages
37,112
The brake booster has no issues running off a single cylinder port. No continuous flow. Just charge the booster with vacuum and the flow stops. A couple gulps of air won't disrupt the engine.
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,651
Can I tee my pcv to my brake booster vac hose?

As they said, but put another way, if your booster vacuum is taken from a single runner in the intake, then NO you can't Tee them together.
If on the other hand the booster gets it's vacuum from the common plenum area of the intake, then you probably could.

The bottom line in all this wishy washiness, is that you can't take PCV vacuum from a single port runner. It can only be taken from the common plenum area at the base of, or under the carb.

Paul
 
OP
OP
MonsterBIlly

MonsterBIlly

Sr. Member
Joined
Dec 17, 2015
Messages
461
I get it, bit I do not have a carb. I am running a sniper. So if it's at the large port of the t body won't that basically be vac leak? Will that not mess up the iac in the sniper
 

Broncobowsher

Contributor
Total hack
Joined
Jun 4, 2002
Messages
37,112
No, the Sniper is expecting a PCV.

In fact a speed density throttle body EFI is just about immune from vacuum leaks. The computer doesn't see mass airflow, just manifold pressure. How the air gets into the manifold just bout doesn't matter. It can go around the throttle blades, around the IAC, or through a vacuum port via the PCV. The computer learns what amount of fuel to add when there is a given manifold pressure at a given RPM.

Mass air style EFI is actually more sensitive about the PCV. Since it is actually measuring the amount of air entering the engine, the whole engine, crankcase and all, the make up air for the PCV has to be in the metered air. At this point the engine doesn't really care how much is actually going through the PCV valve itself, the route the air takes doesn't really matter. It is all metered by the computer and the matching fuel is added.

I mentioned the Sniper doesn't really care about vacuum leaks. But there is still a distribution issue that has to be followed. A PCV in a single runner will lean that one cylinder out. The fuel is distributed at the plenum. Adding a vacuum leak to a single runner will alter the fuel distribution in that one cylinder adding air to the mix coming out of the plenum. That is why the PCV is added to the plenum, even distribution of the PCV gasses to all cylinders.
 

gr8scott

Contributor
Bronco Guru
Joined
Jul 1, 2011
Messages
1,890
Hey MonsterBilly, add some of your Bronco's details in your signature. At the top of the page click Quick Links→Edit Signature.
You can keep it simple, engine, trans, transfer case, and of course your Sniper.


I have those on a new roller build I have not fired up yet. Glad to hear they are working for you.

You'll like them. Tall enough to clear rollers and baffled. So nice to not have oil on my covers anymore.
 

Attachments

  • Valve Cover1.jpg
    Valve Cover1.jpg
    104.5 KB · Views: 80
  • Valve Cover2.jpg
    Valve Cover2.jpg
    96.1 KB · Views: 67

trekgurl

Full Member
Joined
Dec 7, 2006
Messages
315
You'll like them. Tall enough to clear rollers and baffled. So nice to not have oil on my covers anymore.

In that first pic where does that hose coming from PVC route too? Some kind of tank? Mine routes back into the carb /or intake,, I think? I need to go look at this again closely.
 

gr8scott

Contributor
Bronco Guru
Joined
Jul 1, 2011
Messages
1,890
In that first pic where does that hose coming from PVC route too? Some kind of tank? Mine routes back into the carb /or intake,, I think? I need to go look at this again closely.

I have my PCV valve routed through a oil catch can. Yours is fine the way it is.

EDIT: Yours is fine if its running to the base of your carb. If its connected to a intake runner, move it.
 

Attachments

  • Oil Catch.jpg
    Oil Catch.jpg
    101.5 KB · Views: 73
Last edited:
OP
OP
MonsterBIlly

MonsterBIlly

Sr. Member
Joined
Dec 17, 2015
Messages
461
If I put my pcv hose to my air filter prior to the sniper, will it work? Will there be sufficient vacuum to open the valve. I currently only have one large vacuum port at the base of my sniper I use for my brakes. There are no other 3/8 vacuum ports to connect too.
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,651
No. Your PCV hose needs full vacuum. So putting it to the air cleaner defeats it's purpose.
You must have two separate hoses for the PCV system to work. One is vacuum. That's the one to the base of the Sniper. The other is simple atmospheric pressure return for clean air to get back into the engine. That's the one that goes to the air cleaner.
And never do the two connect.

I'm surprised there were not two ports on the sniper, but if not then the one port must be for PCV. In fact some throttle-bodies actually state "PCV" right on the body and in the instructions.
What intake manifold do you have? Most have at least one port into the back somewhere. Usually in just one runner, but sometimes in a common area. That one runner must do multiple duties which is why manufacturers install vacuum manifolds, often in the shape of a "vacuum tree" with multiple ports.
That's where you can connect the brake booster hose.

Do you have such a port?
Maybe this is one of those times you can Tee into the PCV line to get your brake vacuum? I've always kept them completely separate, but not sure if Tee-ing them together would cause trouble or not.

Just as long as the PCV gets full vacuum at the base of the throttle body, that part is good.

Paul
 

gr8scott

Contributor
Bronco Guru
Joined
Jul 1, 2011
Messages
1,890
My above statement about the PCV valve "robbing" vacuum from the booster is from personal experience. To clean up my hoses,
I once ran PCV, vacuum booster, and C4 to a vacuum tree on the back of my carb. It took a really long time for the booster to "fill"
for the brakes to feel right, and it was for only one or two brake pumps. After that it felt like I had manual brakes and the pedal
was near the floor. I re-ran the PCV to the front of the carb and my booster started working normally. I run hydro brakes now
so its not a issue. I've since put that vacuum tree in the lower intake runner with my C4 and vacuum gauge connected to it,
and the PCV runs to the back of the carb, via a oil catch can.
 

Attachments

  • 20190915_093101.jpg
    20190915_093101.jpg
    85.6 KB · Views: 64

gr8scott

Contributor
Bronco Guru
Joined
Jul 1, 2011
Messages
1,890
What intake manifold do you have? Most have at least one port into the back somewhere. Usually in just one runner, but sometimes in a common area. That one runner must do multiple duties which is why manufacturers install vacuum manifolds, often in the shape of a "vacuum tree" with multiple ports.
That's where you can connect the brake booster hose.

Do you have such a port?

Paul

Paul asked a good question. What manifold do you have? My Edelbrock Performer Intake Manifold has two ports behind the carb.
 

Attachments

  • Intake Runner Ports.jpg
    Intake Runner Ports.jpg
    70.5 KB · Views: 70
OP
OP
MonsterBIlly

MonsterBIlly

Sr. Member
Joined
Dec 17, 2015
Messages
461
I have a Weiand stealth intake intake. It has no bosses for vac.

I tee'd the pcv I to my brake booster a d pretty much lost brake vacuum. Feel like I have manual brakes.
There is a plugged port on the base of the sniper that appears to be vac but nothing in the manual states what it for.
I also dint know if I use it for brakes or ocv if it will effect the other as the tee does.
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,651
it should not effect the other. That would be largely due to the larger volume of the plenum area under the throttle body being able to support both from all 8 cylinders.
At least I've never seen one that had a problem with that.

Was there no additional fittings or other accessories included with the Sniper? If not you can usually get an appropriately threaded hose barb fitting at your local parts store or hardware store that would work in that blocked off port.
Maybe it's the FiTech that has them both already fitted and ready to plumb, but I remember seeing instructions posted here before that showed the underside of the throttle-body with both Brakes and PCV listed for the ports. Apparently was not the Sniper based on your experience.

But that might be due to the fact that most intakes other than the Weiand apparently have additional vacuum ports available so most installs only need the one for the PCV on the TB.
The capped and sealed port would be to keep vacuum leaks to a minimum I would presume.
Since the rubber caps for hose barbs that we see these days are not lasting very long before they fail and leak, this might be a good thing for most Sniper owners.

I would uncap it and thread in a fitting for the brakes. But at this point it doesn't hurt to call Holley either.
Are the instructions online? I notice that not all of our Sniper kits are so blessed, but I did find this one: https://www.wildhorses4x4.com/produ...-Master-Kit-Black/Fullsize_Bronco_Fuel_System on one of the 4bbl kit pages that might help. Both a pdf and video in case that helps.

Paul
 

gr8scott

Contributor
Bronco Guru
Joined
Jul 1, 2011
Messages
1,890
thanks for the real-world experience with sharing the vacuum. I missed it or forgot it in that short time!
Did you make those two vacuum manifold/tree thingies? Or were there some off-the-shelf pieces you could find?

Paul

It could be made by someone with the proper tools and skills, but I bought mine. Kind of pricey, but hey, stimulus money, right?

https://stores.hi-potek.com/hipotek-intake-manifold-vacuum-tree/

I tee'd the pcv I to my brake booster and pretty much lost brake vacuum. Feel like I have manual brakes.

And now we have another member with real-world experience :)

Hey MosterBilly, post a link to the Sniper unit you have, we'll see if we can help you out.
 

JWMcCrary

Contributor
Bronco Guru
Joined
Oct 14, 2004
Messages
5,001
I have my PCV valve routed through a oil catch can. Yours is fine the way it is.

EDIT: Yours is fine if its running to the base of your carb. If its connected to a intake runner, move it.

Do have a part number or those spark plug wire holders?
 
Top