• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Narrowing an 08 super 60

joshforrest12

New Member
Joined
Feb 21, 2021
Messages
16
How's it going everyone? So I'm currently in the process of narrowing a Dana 60 out of an 08 superduty. I'm curious if anyone has done this and what things I should be mindful of. How much was narrowed from the passenger side and what not. This will be going under a 66' u15. I have a local company that will be helping with custom fabrication to make this work.
 

Broncobowsher

Contributor
Total hack
Joined
Jun 4, 2002
Messages
37,112
Really depends on what you want out of it. Most people doing a 60 will be running larger tires and a little width gain is generally wanted.

What are your plans for the hubs? Are you keeping the metric bolt pattern? Match to the rear with an axle from the same donor? Converting the front to a different bolt pattern?

I'm guessing most swapping this axle in are running it in stock superduty width. No narrowing.

What size tires are you planning on using?
 

Apogee

Contributor
Bronco Guru
Joined
Nov 26, 2005
Messages
6,348
Loc.
Tangent, OR
In addition to what was asked above, what's the intended use? Is this going to be an all-around trail rig, dedicated rock rig, pre-runner, street queen, etc?

In general, most wouldn't bother to build a D60 for an EB unless you were planning on running 37's or larger and difficult trails/rocks, and more likely 40's or bigger, as you can build the D44's to reliably handle 35's for most situations.
 

sprdv1

Contributor
REBEL
Joined
Mar 8, 2007
Messages
81,996
Definitely what the fellas said.. provide a little more details and the experts attached will give you the advice you need
 
OP
OP
J

joshforrest12

New Member
Joined
Feb 21, 2021
Messages
16
I'm wanting to turn it into a trail rig. Run bigger tires and pmf suspension is going to be helping with the custom fabrication. Keeping same hubs to run the 8x170 lug pattern. And see if I can get new axle shafts for the 9” rear. I work in a differential shop so getting those shouldn't be an issue. And I'll most likely be running a 3 link in the front. Changing coil buckets to match the super 60 so doing a coil over conversion will be easier. There's a lot of custom fabrication going to be involved. Just overall curious what guys that have done it are doing to make it fit underneath. I'm planning on using either 37-40” tires.
 

Broncobowsher

Contributor
Total hack
Joined
Jun 4, 2002
Messages
37,112
In that case you narrow it to get the width you want. There is no set number.
Generally for what you are trying to built, don't narrow it at all.

For the rear you can find a 9" from a 70's or early 80's F150 or Econoline that will be the same general width as the 60. Any halfway decent axle shop can make that metric bolt pattern and hub index for the brake rotor.
 

EB70

Sr. Member
Joined
Jun 9, 2006
Messages
730
FWIW Dana makes a slightly narrower SD60 bolt in for new Wranglers. I think it is about 68" WMS to WMS. You can use the long side out of that axle and cut your housing down. You get about 66.5" WMS to WMS and an upgrade to a 1550 shaft on that side. Not too expensive. Seems like the shaft is about 5" shorter than a regular SD 60.
 

BUCKWILD

Sr. Member
Joined
Jun 20, 2016
Messages
355
Loc.
Butte county
cutting approximately 4" off makes it the same length as a dodge/chevy inner shaft and are readily available to replace
 

Madgyver

Bronco Madman
Joined
Jul 30, 2001
Messages
15,030
following.. i thought about cutting the SD60 but decided not to. i just got wheels with the backspacing that I wanted to make it work. keeping it simple.
 
OP
OP
J

joshforrest12

New Member
Joined
Feb 21, 2021
Messages
16
Okay cool. So if I keep the same width, how much of a pain in the ass is getting everything to line up suspension wise? That was my original plan to go full width, but reading up on it, seemed like a real pain in the ass. Pmf is doing a low profile sub frame to run the radius arms and sub alpha joints. And going to be using their whole steering system setup as far as trac bar, drag link etc. everything is going to be custom fab. Plus swapping out the coil buckets for their coil over conversion setup. Not too expensive and easier to run that sort of setup with going to crazy on the fabrication part.
 

jmhend

Bronco Guru
Joined
Dec 25, 2007
Messages
2,768
Very interesting thought. Have you thought about a 609? Depending on your engine, trans, transfer case you could possibly have some clearance issues. If you are ultimately going to heavily modify the '08 Dana 60 thought I would ask. Post up some pictures of your progress when you get started.

Where are you located?

This is also a great link with a few questions and recommendations:

https://classicbroncos.com/forums/showthread.php?t=310794&highlight=Dana+60&page=2
 
Last edited:

BUCKWILD

Sr. Member
Joined
Jun 20, 2016
Messages
355
Loc.
Butte county
So I know its been done but the 05+ 60 the pinion ends up under the drivers frame rail and I dont like the link angles when there so I built a wider frame
 
OP
OP
J

joshforrest12

New Member
Joined
Feb 21, 2021
Messages
16
Jmhend I haven't. I stopped by pmf today and the owner Trevor hall came up with a game plan. They have low profile sub frames they built in the past for smaller applications. They specialize in superduty lifts. But basically it allows the radius arms to connect to them as well as traction bars. So they are going to make the traction bars extra long, I figure out what length I need them and they cut them down and weld them. Only big modification on the axle is narrowing it. Everything else will be measured and made to fit on the bronco. Only big modification I'll have on this now, is when I swap the coil buckets, I'll have to brace them. I guess the rule of thumb is farther front the frame you go the more it wants to flex. So between the front radius arms and sub frame, it's around 1400$. Traction bars around 200. And whatever the cost on shocks are. Whether I go king or another brand. So far it look like the shocks are going to be the biggest expense. I'm currently in Tucson, Az
 

jmhend

Bronco Guru
Joined
Dec 25, 2007
Messages
2,768
Jmhend I haven't. I stopped by pmf today and the owner Trevor hall came up with a game plan. They have low profile sub frames they built in the past for smaller applications. They specialize in superduty lifts. But basically it allows the radius arms to connect to them as well as traction bars. So they are going to make the traction bars extra long, I figure out what length I need them and they cut them down and weld them. Only big modification on the axle is narrowing it. Everything else will be measured and made to fit on the bronco. Only big modification I'll have on this now, is when I swap the coil buckets, I'll have to brace them. I guess the rule of thumb is farther front the frame you go the more it wants to flex. So between the front radius arms and sub frame, it's around 1400$. Traction bars around 200. And whatever the cost on shocks are. Whether I go king or another brand. So far it look like the shocks are going to be the biggest expense. I'm currently in Tucson, Az

Sounds like a plan.

Have you looked at ORI struts? They are a little more but offer so much benefit especially for the limited room. This would eliminate the need for shocks, coils and bumpers.

https://www.polyperformance.com/ori...boiOuzbERLD7nzcX7u7WDF_F_vyb8IugaAjWIEALw_wcB

Either way good luck.
 
OP
OP
J

joshforrest12

New Member
Joined
Feb 21, 2021
Messages
16
Nice yea I haven't, but better priced. Might go that route. I'm definitely having second thoughts. Most local shops stopped custom axle builds til next year. They are super swamped. I'm debating just going full width and finding a donor full 9” and swapping 3rd members in it. Just trying to gamble what the outlook would be going full width. I'm not sure what the min lift would be to rub a full width sd60. Do any of you know?
 

Madgyver

Bronco Madman
Joined
Jul 30, 2001
Messages
15,030
Nice yea I haven't, but better priced. Might go that route. I'm definitely having second thoughts. Most local shops stopped custom axle builds til next year. They are super swamped. I'm debating just going full width and finding a donor full 9” and swapping 3rd members in it. Just trying to gamble what the outlook would be going full width. I'm not sure what the min lift would be to rub a full width sd60. Do any of you know?

I'm going for 10" bottom of frame to top of axle. That equates to 2.5" of lift. Stuffing 37" tires on them. I'll do what I will need to do to make it fit. And staying full width.
 
OP
OP
J

joshforrest12

New Member
Joined
Feb 21, 2021
Messages
16
I'm going for 10" bottom of frame to top of axle. That equates to 2.5" of lift. Stuffing 37" tires on them. I'll do what I will need to do to make it fit. And staying full width.

Nice. Yea I was talking to a guy on ig that runs a full width 9 and a Dana 60. Might be easier to just keep everything full width. I already have a 3.5” lift. So I'm sure it'll fit. With the way I'm going, it'll be around 6” of lift. I can get a full width 9 for like next to nothing at work. Just was wondering what other issues guys ran into building full width axles.
 

Madgyver

Bronco Madman
Joined
Jul 30, 2001
Messages
15,030
Nice. Yea I was talking to a guy on ig that runs a full width 9 and a Dana 60. Might be easier to just keep everything full width. I already have a 3.5” lift. So I'm sure it'll fit. With the way I'm going, it'll be around 6” of lift. I can get a full width 9 for like next to nothing at work. Just was wondering what other issues guys ran into building full width axles.

while you're at it, go with a 4-link and swaybar.
 
Top