• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Starting problems

CopperBronco

Sr. Member
Joined
Aug 13, 2021
Messages
389
My Bronco is having problems starting after having it sit, it can do this normally especially after sitting for 4-5 days. This is the first time I can’t get it to truly start though… Here's my setup:

302 V8, 2brl Carb, electronic ignition, not the old points, have a 3G alternator, high torque mini starter, brand new optima red top agm battery last month as old one was dying, testing at 12.5 volts at battery and relay after cranking on it a bit. 11.7 volts at old style 70s fuse box… this has been typical while I’ve had it… and often starts no problem.

New taylor spark plug wires as of last year each wire with .01 resistance. I have grounds from battery to engine block to the frame. Also lots of other grounds all around the Bronco. I've been through most of them and cleaned them up not too long ago as I want to avoid gremlins. I've also lightly sanded and cleaned the inside top metal point of the distributor to remove carbon build up which I had some.

When I go to start my Bronco, it'll turn over nice and fast from the starter, but just won't start. Engine fan will start to turn… Sometimes I end up flooding it like last night. It started briefly but then couldn't sustain and of course I couldn't give it gas as it already had too much, I let it sit over night to get rid of flooding, but still won't start.

Hooked up remote starter and ran inline spark plug test… got spark, but longer I ran starter weaker the spark got… wondering if plugs are wet… how long does it take those to dry? I’d rather not pull them all out manually… spark plugs are newer as well if I recall right… replaced a yr ago…

Would love any advice or diagnostics I should run.
 

Bronco-Brian

Full Member
Joined
Jun 30, 2015
Messages
306
Loc.
Lake Oswego, OR
I think it is best to isolate what problem exists after sitting. Is it spark, or is it fuel (flooding)? You should be able to brainstorm some tests during the period it will restart. Fuel flooding is most likely in my mind. A couple things to try: Make sure your fuel tank caps are not allowing the tanks to build pressure. Pressure can force fuel to the carb past the fuel pump even when not running. Secondly, make sure that no fuel drips into manifold after a hot shutdown - a sign that the carb needle and seat are kaput. Also check your choke. For now, I would adjust choke to the lean side to avoid future flooding.

You can lock off or remove the fuel line to check the 1st item. I have found once a set of plugs are flooded, the only way to revive them is to remove them and completely dry them out using a torch (or just replace with new). What plugs are you using?

Keep posting what you find. Good luck, Brian
 
OP
OP
C

CopperBronco

Sr. Member
Joined
Aug 13, 2021
Messages
389
I think it is best to isolate what problem exists after sitting. Is it spark, or is it fuel (flooding)? You should be able to brainstorm some tests during the period it will restart. Fuel flooding is most likely in my mind. A couple things to try: Make sure your fuel tank caps are not allowing the tanks to build pressure. Pressure can force fuel to the carb past the fuel pump even when not running. Secondly, make sure that no fuel drips into manifold after a hot shutdown - a sign that the carb needle and seat are kaput. Also check your choke. For now, I would adjust choke to the lean side to avoid future flooding.

You can lock off or remove the fuel line to check the 1st item. I have found once a set of plugs are flooded, the only way to revive them is to remove them and completely dry them out using a torch (or just replace with new). What plugs are you using?

Keep posting what you find. Good luck, Brian
Thanks Brian! Fuel caps are vented kind, and I have a EVAP charcoal canister to my air cleaner… should be good there…

I have an electric choke… no idea if that contributed… ideally slows down fuel a bit at first and then opens up as you crank.

You said make sure no fuel drips into manifold… so remove carb and take look? Haven’t done that before. I’ve practically torn apart most areas of the bronco… really engine and transmission are both bigger areas I haven’t gone deep yet and are probably most important. I’ll dig in.
 
OP
OP
C

CopperBronco

Sr. Member
Joined
Aug 13, 2021
Messages
389
Here is video of inline spark plug on plug #1… can see it get weaker as it cranks… my distributor and coil are old… wiring isn’t that new either… where do I ground to to test voltage on coil while key is on?

I think that wiring harness in my garage might be in my immediate future… was hoping to drive thru summer without doing that…
 

Attachments

  • IMG_6297.mov
    20.8 MB

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
I have an electric choke… no idea if that contributed… ideally slows down fuel a bit at first and then opens up as you crank.
Not sure what you’re describing.
An electric choke is still closed when cold. This closed position adds MORE gas to the air.
It only opens up, leaning out the mixture, as the spring inside the housing heats up.
It heats up through a combination of both engine heat, and more quickly due to the electrical current flowing into it.

What is it connected to though? If directly to the ignition switch, then you can turn the key on, and the choke will slowly open up while you watch.
If it’s connected to the stator circuit of the alternator, like from the factory, it will only open up after the engine starts.
You said make sure no fuel drips into manifold… so remove carb and take look? Haven’t done that before.
No. Remove the air cleaner and look down inside with the carburetor still attached.

When you have a flooded condition, such as it sounds like you were experiencing, the quickest cure (hopefully) is to hold the throttle all the way open while you crank the starter.
Don’t pump it, just hold it open.

This is the time tested, tried and true method of clearing a flooding situation. As long it’s not too serious.
 
OP
OP
C

CopperBronco

Sr. Member
Joined
Aug 13, 2021
Messages
389
Not sure what you’re describing.
An electric choke is still closed when cold. This closed position adds MORE gas to the air.
It only opens up, leaning out the mixture, as the spring inside the housing heats up.
It heats up through a combination of both engine heat, and more quickly due to the electrical current flowing into it.

What is it connected to though? If directly to the ignition switch, then you can turn the key on, and the choke will slowly open up while you watch.
If it’s connected to the stator circuit of the alternator, like from the factory, it will only open up after the engine starts.

No. Remove the air cleaner and look down inside with the carburetor still attached.

When you have a flooded condition, such as it sounds like you were experiencing, the quickest cure (hopefully) is to hold the throttle all the way open while you crank the starter.
Don’t pump it, just hold it open.

This is the time tested, tried and true method of clearing a flooding situation. As long it’s not too serious.
Thanks for this, will pull air cleaner. Choke is wired to ignition… and thanks for correction on air/fuel! As for flooding… how long can you hold down pedal and crank? I’ve tired it for about 5-8 seconds at a time a few times after letting Bronco sit and hopefully unflood… will try again tomorrow. Since I can smell fuel I’m going to assume I most likely have a spark problem and not a fuel delivery problem, is that a wise place to start? Been reading every thread I can tonight on here, learning a lot!
 

gnpenning

Contributor
Bronco Slave
Joined
Dec 26, 2011
Messages
2,601
Loc.
I have more questions than answers.
Every time you release the throttle pedal and step on it again if carb is working correctly you are giving it another shot of fuel and adding to a potential flooding issue.

A simplified version of what you need for a motor to run is spark at the right time, fuel in the right amount and compression. You already know you have spark, the next question would be is it at the right time? A timing light will quickly answer that question.

Just because you smell fuel doesn't mean you don't have any spark. It can mean the carb is flooding the motor, so doing what Paul suggested is a logical place to start. You are checking to see if you are having unmetered fuel dumping in while the motor is cranking. Hopefully you aren't getting any backfiring.

The fact you are smelling fuel is extra incentive to have a fire extinguisher handy.

Pull your oil dipstick and check for fuel in your oil as well.
 

EPB72

Contributor
Bronco Guru
Joined
Jul 13, 2019
Messages
1,216
Loc.
Pleasant Hill, CA
On your vieo you have weak, inconsistent spark .. with a couple of brite hits 2 or 3 time in video.. is that spark tester adjustable or is it the simple bulb style ???....prefer the adjustable thexton one but ok..


could preform same test on coil wire ... same results ,, check voltage at coil positive terminal.. could even jumper from bat pos. to positive side of coil ..
 

blade

Contributor
Maker of sharp things
Joined
May 13, 2020
Messages
195
Loc.
Santa Fe
Being that you have had problems with flooding you may need to pull the plugs and clean them or replace them. Plugs can foul from being fuel soaked repeatedly causing them to not fire. I would at least pull the plugs and check them.
 
OP
OP
C

CopperBronco

Sr. Member
Joined
Aug 13, 2021
Messages
389
Measured volts at coil, have 10.0 volts when key is on… supposedly this is enough, IDK if I have a ballast resistor, but those take it down to 7 bolts supposedly, but this does mean I’m losing voltage along the way… jumped the battery to coil and still didn’t get consistent spark… will pull plugs next.
 
OP
OP
C

CopperBronco

Sr. Member
Joined
Aug 13, 2021
Messages
389
Here is spark plug… definitely seen better days, but no build up on actual spark area… will pop new one in and just see how spark light performs… doesn’t look wet. If that doesn’t work onto carburetor and fuel delivery…
 
OP
OP
C

CopperBronco

Sr. Member
Joined
Aug 13, 2021
Messages
389
Spark plugs
 

Attachments

  • IMG_6314.jpeg
    IMG_6314.jpeg
    194.2 KB · Views: 139
  • IMG_6313.jpeg
    IMG_6313.jpeg
    415.4 KB · Views: 101
OP
OP
C

CopperBronco

Sr. Member
Joined
Aug 13, 2021
Messages
389
its official, I’m a super idiot, or just getting old… I forgot that I’d turned fuel valve off before I left town… float bowl was dry and wouldn’t release fuel… 🙄… regardless got a mini education in troubleshooting my electrical and fuel delivery systems, I’ll take the knowledge and count it as a win. Apologies if I wasted any of your time, this forum always amazes me. I’d be up a creek without it.
 

NJBronk

Contributor
Sr. Member
Joined
Oct 11, 2022
Messages
369
its official, I’m a super idiot, or just getting old… I forgot that I’d turned fuel valve off before I left town… float bowl was dry and wouldn’t release fuel… 🙄… regardless got a mini education in troubleshooting my electrical and fuel delivery systems, I’ll take the knowledge and count it as a win. Apologies if I wasted any of your time, this forum always amazes me. I’d be up a creek without it.

After replacing my intake gasket and putting on a new carb, my truck was running great. Forgot to tie the radiator hose back out of the way like the PO had and the belt sliced a hole into it. After replacing the hose, I took it to a cruise night 30 minutes from home, then around town the next day. Towards the end of the day I looked down and saw my oil pressure was pegged to zero. My heart sank into my stomach and I limped home carefully. I was driving myself crazy trying to figure it out (remove distributor and check pump drive shaft, check oil level, look for leaks, etc.), then when I was about to order a mechanical fuel pressure gauge I realized I never put the wire back on the oil pressure sending unit after reinstalling the intake...

Two of probably 20 examples where I forget something that I did just days before...
 
Top