• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

New brake kits

duffymahoney

Contributor
Bronco Guru
Joined
Apr 26, 2015
Messages
2,734
Got a link? I don't see that on their site. That must be a pretty expensive kit.
I am sure that is an expensive kit, the owner and I chat about it. I dislike wilwood, so I would rather not use their products.

I thought it had launched, but I don't see it on their site. I plan to reuse an aluminum caliper from another rig, it's just going to be a large undertaking. Currently knee deep developing boat parts and Datsun parts:)
 

LittleBeefy

Huge Brakes - www.hugebrakes.com
Joined
Aug 1, 2023
Messages
67
@LittleBeefy thanks for putting into geeky engineering speak what I have theorized about and supports my theories. Makes me feel less crazyšŸ˜‚
Bachelors and Masters in engineering from Georgia Tech. Geeky Engineering is my second language! I plan to have ā€œWork = Force x Distanceā€ put on my gravestone hahaha. Happy to help.
 

Yeller

Contributor
Bronco Guru
Joined
Mar 27, 2012
Messages
7,692
Loc.
Rogers County Oklahoma
Bachelors and Masters in engineering from Georgia Tech. Geeky Engineering is my second language! I plan to have ā€œWork = Force x Distanceā€ put on my gravestone hahaha. Happy to help.
That splains that šŸ˜‚

In the EB world we need a plastic reservoir master with a 1-5/16 bore that is the same height as a corvette style master. Many of us are running large enough calipers that we need this much master cylinder to push enough fluid for a good pedal travel ratio. Actually, would be happy with a corvette style master, just never seen one with a large enough bore. The issue some of us have is the only thing we've found that is close to fitting under the hood is for a 85 chevy K30. it works but mine hits the hood and they are terrible about the lids leaking. I have nowhere to move the master to, it is a special build that everything is close to everything LOL. we also need a 2" bore caliper that fits a 1.295" thick rotor for better bias. I also understand that this stuff is what you do for a living, not expecting you to give out info for free, I'm one of the few shop owners that gives virtually everything away LOL.
 

LittleBeefy

Huge Brakes - www.hugebrakes.com
Joined
Aug 1, 2023
Messages
67
That splains that šŸ˜‚

In the EB world we need a plastic reservoir master with a 1-5/16 bore that is the same height as a corvette style master. Many of us are running large enough calipers that we need this much master cylinder to push enough fluid for a good pedal travel ratio. Actually, would be happy with a corvette style master, just never seen one with a large enough bore. The issue some of us have is the only thing we've found that is close to fitting under the hood is for a 85 chevy K30. it works but mine hits the hood and they are terrible about the lids leaking. I have nowhere to move the master to, it is a special build that everything is close to everything LOL. we also need a 2" bore caliper that fits a 1.295" thick rotor for better bias. I also understand that this stuff is what you do for a living, not expecting you to give out info for free, I'm one of the few shop owners that gives virtually everything away LOL.
I am now very confused. 1 5/16ā€ is an enormous bore. That’s what you would find on a 97 Suoer Duty which has dual 60mm pistons at all 4 wheels and hydro boost assist. Why do you need an MC with such a massive bore? What calipers are you running? Stock is 2 7/8ā€ so 2ā€ seems undersized. What rotors are you running that are so thick?
 

jamesroney

Contributor
Bronco Guru
Joined
Sep 11, 2007
Messages
2,607
Loc.
Fremont, CA
I am now very confused. 1 5/16ā€ is an enormous bore. That’s what you would find on a 97 Suoer Duty which has dual 60mm pistons at all 4 wheels and hydro boost assist. Why do you need an MC with such a massive bore? What calipers are you running? Stock is 2 7/8ā€ so 2ā€ seems undersized. What rotors are you running that are so thick?
Need is a funny word.

Nobody needs a 1-5/16 master cylinder in a 3800 lb car.

The problem is that the pedal ratio in the original Bronco was designed for manual drum brakes. Brake evolution over time has maintained that same pedal ratio. When you add Hydroboost to the original pedal geometry, you end up short-stroking the hydroboost input. In order to reduce pedal travel to approximate a "normal" movement, you "need" to oversize the master cylinder piston.

Every once in a while, someone will try to run the factory K30 caliper when they do a Dana 60 axle swap, and it ends up with a 3.368 diameter bore caliper. Those pistons displace a lot of fluid, and the factory K30 master cylinder bore is 1.31 inch. I think that @Yeller plays with the big stuff...
 
Last edited:

LittleBeefy

Huge Brakes - www.hugebrakes.com
Joined
Aug 1, 2023
Messages
67
Need is a funny word.

Nobody needs a 1-5/16 master cylinder in a 3800 lb car.

The problem is that the pedal ratio in the original Bronco was designed for manual drum brakes. Brake evolution over time has maintained that same pedal ratio. When you add Hydroboost to the original pedal geometry, you end up short-stroking the hydroboost input. In order to reduce pedal travel to approximate a "normal" movement, you "need" to oversize the master cylinder piston.

Every once in a while, someone will try to run the factory K30 caliper when they do a Dana 60 axle swap, and it ends up with a 3.368 diameter bore caliper. Those pistons displace a lot of fluid, and the factory K30 master cylinder bore is 1.31 inch. I think that @Yeller plays with the big stuff...
That makes sense now. Have you considered switch out your pedal assembly for one with a lower ratio?
 

Yeller

Contributor
Bronco Guru
Joined
Mar 27, 2012
Messages
7,692
Loc.
Rogers County Oklahoma
@LittleBeefy , @jamesroney is correct, I play with the big stuff. GM single piston calipers for an 85 k30 on a yes…. GM 60, pumpkin on the wrong side and all. No hydroboost, 9ā€ vacuum booster. Brakes are great, pedal travel is good and stops well. The rear rotors are front 85 K20 front rotors, with currently 2-3/4 bore GM calipers. Bias is horrible, manual valve is closed as much as it will go and barely sufficient, needs a smaller caliper. The master rubbing on the hood is annoying too šŸ˜‚

My signature doesn’t lie, I tend to ride the short bus lol. And if you want a different kind of build thread read, it’s in my signature as well, it’s just a well disguised buggy that does wear most of a bronco tub šŸ˜Ž
 
Last edited:
OP
OP
toddz69

toddz69

Sponsor/Vendor
Bronco Guru
Joined
Nov 28, 2001
Messages
11,222
You don't have the stock Bronco power brake bracket, do you, @Yeller? That reduces the stock manual 6:1 pedal ratio a bit.

Todd Z.
 

ksagis

Contributor
Aspiring Bronco Guru
Joined
Jun 15, 2020
Messages
819
Loc.
Austin
Is there anybody that makes a revised pedal geometry for hydro applications with something closer to 4:1?

Seems like it would be a fairly easy conversion, no?
 
Last edited:
OP
OP
toddz69

toddz69

Sponsor/Vendor
Bronco Guru
Joined
Nov 28, 2001
Messages
11,222
Is there anybody that makes a revised pedal geometry for hydros application with something closer to 4:1?

Seems like it would be a fairly easy conversion, no?
I don't know of anyone that does that except one of the hydro kits that mounts to the stock-type angled booster is probably in that range (it's been years since I've measured anything on those brackets so I don't remember what they change the ratio to). Tom's h-boost bracket might change the ratio as well too. I did one conversion on a buddy's truck years ago with the stock angled bracket and as I recall, it had a real good pedal feel when I was done (Ford discs in front, Eldorado's out back and a 1.125" Corvette master iirc).

Within the last year or so, I bumped my master cylinder up to a 1.25" Dodge unit after 20+ years of running a 1.125" Dodge unit (various brake caliper configurations - all 4 wheel disc) and the pedal feel is much better. Much less touchy, better pedal height, less pedal travel, and firmer pedal at the bottom of the travel, and feels more like an OEM installation (my '01 Super Duty as a baseline for pedal feel).

Todd Z.
 

Broncobowsher

Contributor
Total hack
Joined
Jun 4, 2002
Messages
37,111
curious how much brake bias matters with these early broncos and if any of the existing BBKs have calcs to share?
I think brake bias really matters on an early Bronco. Especially when lifted. Short wheelbase, high CG. Under a hard brake stop (if you have the tires and front brakes that can take it), and a bit of a lift, light back end and an heavy nose. You could just about stand it on its nose.

One of the things I found was you can really dial in a lot of brake bias change just by changing pads. How grippy is the pad. That is one of the things I found that I really like about the GM disk conversion. There are so many different pad compounds available. Not talking the local parts store that has 2 versions on the shelf and 3 more in the warehouse. I mean go to a racer supply house or even Speedway motors and you have a few dozen different compounds.
 

Yeller

Contributor
Bronco Guru
Joined
Mar 27, 2012
Messages
7,692
Loc.
Rogers County Oklahoma
You don't have the stock Bronco power brake bracket, do you, @Yeller? That reduces the stock manual 6:1 pedal ratio a bit.

Todd Z.
I’m running a Duff bracket. I’ve looked at removing it and moving the assembly outboard further to clear the valve cover but then it hits the alternator. I’ve contemplated going to a 3.5ā€ spring from the 5.5ā€ spring so I can lower my spring tower so I can lower the master cylinder a 1/2ā€ so it stops getting friendly with the hood. I built everything with manual brakes, which is part of the closeness issue.

As for rear brakes. I’ve looked for a thinner rotor to run metric calipers, with no luck. I’ve considered turning them down far enough to fit the calipers but am concerned about warping, taking nearly .200ā€ off is a lot, well past minimum spec.

Truck drives great, but I notice the bias valve being almost closed, it makes the rear brakes slow to react, most would never notice, highway speeds is where it becomes really evident, hold steady pressure and the braking increases as you slow down.
 

LittleBeefy

Huge Brakes - www.hugebrakes.com
Joined
Aug 1, 2023
Messages
67
@LittleBeefy , @jamesroney is correct, I play with the big stuff. GM single piston calipers for an 85 k30 on a yes…. GM 60, pumpkin on the wrong side and all. No hydroboost, 9ā€ vacuum booster. Brakes are great, pedal travel is good and stops well. The rear rotors are front 85 K20 front rotors, with currently 2-3/4 bore GM calipers. Bias is horrible, manual valve is closed as much as it will go and barely sufficient, needs a smaller caliper. The master rubbing on the hood is annoying too šŸ˜‚

My signature doesn’t lie, I tend to ride the short bus lol. And if you want a different kind of build thread read, it’s in my signature as well, it’s just a well disguised buggy that does wear most of a bronco tub šŸ˜Ž

The problem you have is a combination of factors and so there are different ways to solve it. First, you have far too much mechanical advantage in the pedal so you are making up for it by reducing the hydraulic advantage in the MC (I’m sure you know that). That creates the second problem which is that you are needing a a bore size in your MC that is generally reserved for hydroboost based systems, but you are using a vacuum booster. It’s virtually impossible to find any MC with a bore that large that fits a vacuum booster. Consider a couple of options. First you can reduce your mechanical advantage with a pedal kit designed with lower ratio. Second, you could look for a booster mount that will reduce mechanical advantage of the pedal on the MC. Third, you can switch to an Astro boost setup which will give you significantly more options in MC.

Or you could use the MC from a 1983 Corvette 🤣. After cracking out on an MC search last night for a few hours I couldn’t find another MC like what you are looking for.
 
OP
OP
toddz69

toddz69

Sponsor/Vendor
Bronco Guru
Joined
Nov 28, 2001
Messages
11,222
The problem you have is a combination of factors and so there are different ways to solve it. First, you have far too much mechanical advantage in the pedal so you are making up for it by reducing the hydraulic advantage in the MC (I’m sure you know that). That creates the second problem which is that you are needing a a bore size in your MC that is generally reserved for hydroboost based systems, but you are using a vacuum booster. It’s virtually impossible to find any MC with a bore that large that fits a vacuum booster. Consider a couple of options. First you can reduce your mechanical advantage with a pedal kit designed with lower ratio. Second, you could look for a booster mount that will reduce mechanical advantage of the pedal on the MC. Third, you can switch to an Astro boost setup which will give you significantly more options in MC.

Or you could use the MC from a 1983 Corvette 🤣. After cracking out on an MC search last night for a few hours I couldn’t find another MC like what you are looking for.
Having not messed around with the 80-86 trucks, like your 84, much at all - what kind of pedal ratio do they have?

Todd Z.
 

ksagis

Contributor
Aspiring Bronco Guru
Joined
Jun 15, 2020
Messages
819
Loc.
Austin
I don't know of anyone that does that except one of the hydro kits that mounts to the stock-type angled booster is probably in that range (it's been years since I've measured anything on those brackets so I don't remember what they change the ratio to). Tom's h-boost bracket might change the ratio as well too. I did one conversion on a buddy's truck years ago with the stock angled bracket and as I recall, it had a real good pedal feel when I was done (Ford discs in front, Eldorado's out back and a 1.125" Corvette master iirc).

Within the last year or so, I bumped my master cylinder up to a 1.25" Dodge unit after 20+ years of running a 1.125" Dodge unit (various brake caliper configurations - all 4 wheel disc) and the pedal feel is much better. Much less touchy, better pedal height, less pedal travel, and firmer pedal at the bottom of the travel, and feels more like an OEM installation (my '01 Super Duty as a baseline for pedal feel).

Todd Z.
I haven't looked at the factory power brake booster bracket lately, but from memory, I don't remember much of a difference in the linkage lengths in it, and thought all of the pedal ratio was set inside the truck at the pedal.

Does anybody have better data then my crappy memory?

First you can reduce your mechanical advantage with a pedal kit designed with lower ratio.

You aware of somebody who sells one by chance?

Or you could use the MC from a 1983 Corvette 🤣.

Like this one? :)
 

LittleBeefy

Huge Brakes - www.hugebrakes.com
Joined
Aug 1, 2023
Messages
67
Having not messed around with the 80-86 trucks, like your 84, much at all - what kind of pedal ratio do they have?

Todd Z.
I don’t have the stock pedal ratio (or the stock pedal for that matter). I switched to hydroboost and installed a brake pedal from a 1997 SD to reduce my pedal ratio. The are interchangeable on the bracket (just hard to find).
 

LittleBeefy

Huge Brakes - www.hugebrakes.com
Joined
Aug 1, 2023
Messages
67
I haven't looked at the factory power brake booster bracket lately, but from memory, I don't remember much of a difference in the linkage lengths in it, and thought all of the pedal ratio was set inside the truck at the pedal.

Does anybody have better data then my crappy memory?



You aware of somebody who sells one by chance?



Like this one? :)

Successful rickroll. Thanks for the laugh.

I’m not sure on the difference between early, later and aftermarket pedal assemblies. Maybe someone with more experience on that can chime in.

One other option is welding a lower brake rod attachment point on your existing pedal. That would lower your ratio. But that might give the rod a funny angle. A way to resolve that would be to modify your firewall so that your booster mounts lower. I’m not familiar with the firewall and obstructions on the EB. Is that even possible?
 

jamesroney

Contributor
Bronco Guru
Joined
Sep 11, 2007
Messages
2,607
Loc.
Fremont, CA
I’m running a Duff bracket. I’ve looked at removing it and moving the assembly outboard further to clear the valve cover but then it hits the alternator. I’ve contemplated going to a 3.5ā€ spring from the 5.5ā€ spring so I can lower my spring tower so I can lower the master cylinder a 1/2ā€ so it stops getting friendly with the hood. I built everything with manual brakes, which is part of the closeness issue.

As for rear brakes. I’ve looked for a thinner rotor to run metric calipers, with no luck. I’ve considered turning them down far enough to fit the calipers but am concerned about warping, taking nearly .200ā€ off is a lot, well past minimum spec.

Truck drives great, but I notice the bias valve being almost closed, it makes the rear brakes slow to react, most would never notice, highway speeds is where it becomes really evident, hold steady pressure and the braking increases as you slow down.
Don't forget that the bias ratio goes with the square of the piston diameter. So your 3.368 front pistons have 8.9 square inches of piston area. Your rear calipers have 2-3/4 pistons with 5.93 square inches of area. (that's 66% bigger) Typical D60 (1 ton) front rotors are 12-7/8 diameter, and the 3/4 ton GM fronts (adapted for use on the rear) are 12-1/2. Most people think that the 1 ton GM brakes are a lot bigger than the 3/4 ton stuff. But it's really not. It's just a lot heavier. They had to stay relatively small diameter to fit under the 16 inch wheel. Braking force acts linear with rotor diameter, and that contributes another 3% difference. (and yes, I know it's really an (r cross F) vector.)

Nominal values for ideal brake bias in a 3800 lb, 93 inch wheelbase high CG vehicle can be found in the 2003 Wrangler Rubicon. It has:
Front Disc piston = 2.60
Rear Disc piston = 1.89
Front rotor dia = 11.03
Rear rotor dia = 11.22
Intrinsic bias = caliper bias, rear area 2.80 sq in / front piston 5.3 sq in = 53% + rotor bias, 11.03/11.22=2% so let's call it 51%.
(I use the '03 Rubicon because it approximates a Bronco dimensionally, and it came factory with 4 wheel disc brakes. I do not have the intellectual bandwidth to calculate the relative brake force in a disc/drum scenario, because I cannot calculate the self-energizing effect) But with 4 wheel discs, we can assume away a lot, and the net number is 51%.

Frankly, I am surprised that you need to choke down your rear hydraulic pressure.
 
Top