• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

Rat to Dana 20 Help

Cmaxx252

Contributor
Jr. Member
Joined
Nov 13, 2023
Messages
73
Loc.
Bakersfield
Does anyone have a diagram showing the original parts to mate a RAT 3 speed to a dana 20 T style? Or a thread that explains it.
The d 20 was in the process of getting a c4, with the cut down shaft, and adapter parts. I'd like to go back to the manual 3 speed, but will need a new intermediate housing as the
original had an ear broken off during c4 install.

Broken ear.

Broken adapter.jpg
Broken adapter 2.jpg

Dana 20 side
D 20 side.jpg
 
OP
OP
Cmaxx252

Cmaxx252

Contributor
Jr. Member
Joined
Nov 13, 2023
Messages
73
Loc.
Bakersfield
Evening Gents. I was able to get the intermediate housing off, and the aluminum bearing retainer out to see what I had in there (I wasn't there when it was assembled.
My questions are:
The original spud shaft was shortened 5/8".
If I order the replacement intermediate housing for the RAT, will the aluminum bearing, spud shaft, bearing, clip and seal still work? Im still digging for the dimensions of the OEM bearing retainer.
Best case scenario is that I only need to order the replacement housing. I could see the old mark on the output shaft of the RAT fit inside the spud shaft originally and It seems like plenty
of meat there.

Also, should there be needle bearings down inside where the end of the spud shaft rides when mated together? Circled in red below. When I pulled it apart there were none, but thought
it was supposed to have them.
spud shaft.png

Please advise.

Cody
 

thegreatjustino

Contributor
Red Head Grease Monkey
Joined
Jan 23, 2002
Messages
16,291
Loc.
Stockton, CA
The shortened spud shaft that was used with the C4 will not work with a manual transmission. You need the longer one that's made for a manual.
 
OP
OP
Cmaxx252

Cmaxx252

Contributor
Jr. Member
Joined
Nov 13, 2023
Messages
73
Loc.
Bakersfield
Does it being 5/8 shorter not leave enough body there to handle torque load while in a certain gear?
 

Viperwolf1

Contributor
electron whisperer
Joined
Aug 23, 2007
Messages
24,451
With a shortened manual shaft, you will have less than optimal spline engagement if you use it with a manual trans. Why risk damaging the trans output when it fails? Those manual shafts are easy to find.
 
OP
OP
Cmaxx252

Cmaxx252

Contributor
Jr. Member
Joined
Nov 13, 2023
Messages
73
Loc.
Bakersfield
Ordering the correct length spud shaft, housing and needle bearings. I appreciate the input and help. 😅 If anyone needs a shortened spud shaft for the C4/dana 20 swap ill let it go for cheap + shipping.
 
Last edited:

Oldtimer

Contributor
Jr. Member with Sr. moments
Joined
Feb 4, 2005
Messages
1,802
Loc.
Sunnyvale, CA
I think this bearing retainer is auto tranny only.

1701655542200.png


You will also need the double lip oil seal that goes in extension housing, or tranny gear oil bleeds into transfer case, and then leaks all over back half of Bronco.

1701655762951.png


There are different length adapters, depending on engine and transmmision flavors.
The input shaft for I6 & V8 manual trans are same lengths. (I6 transmission has 3" shorter output shaft)

Per my notes, but have not verified:
V8 RAT T-case adaptor is 8 7/8"
V8 RAN T-case adaptor is 9 3/8"
V8 C4 T-case adapter is 7 1/2"
I6 RAN T-case adaptor is 6 1/2"

RAN has 2.99 1st
RAT has 3.41 1st
RAT tranny is ½” longer than RAN
 
Last edited:

Oldtimer

Contributor
Jr. Member with Sr. moments
Joined
Feb 4, 2005
Messages
1,802
Loc.
Sunnyvale, CA
@Cmaxx252 ,

Could measure your broken adapter, mouting surface to mounting surface, and fill in the blank?

V8 C4 T-case adaptor is ______"
 

jeffncs

Contributor
Bronco Guru
Joined
May 4, 2004
Messages
1,898
Loc.
Raleigh, NC
Does anyone have a diagram showing the original parts to mate a RAT 3 speed to a dana 20 T style? Or a thread that explains it.
The d 20 was in the process of getting a c4, with the cut down shaft, and adapter parts. I'd like to go back to the manual 3 speed, but will need a new intermediate housing as the
original had an ear broken off during c4 install.

Broken ear.

View attachment 914909 View attachment 914910
Dana 20 side
View attachment 914911


Do you still have these parts? Assuming they’ll work on my c4, I’m interested in a shipped price. I’ll send you a PM to take it offline.
 
Top