• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

What have you done to your Bronco today?

BroncoJimbo

Contributor
Long-term owner
Joined
Jun 11, 2014
Messages
291
Loc.
North GA
Apparently I work slow. After 20 years sitting on all the parts I finally took my glove box out of the center console and did a sliding mount on it. Middle picture is where I have to slide it over to clear the bar.
I need to do this. Details?
 

JeepGuy

Contributor
Bronco Guru
Joined
Aug 24, 2006
Messages
1,521
And, we're back... On today's episode of Bronco Life... The box is still doing box things... but in the meantime I took the Bronco out for a little spin after the completed water pump replacement. I'm elated to announce no leaks! Well, no leaks from the Water pump side of things. I was hoping I could fix this without removing the whole heater box but it appears it all has to come out. Should be awesome.
Rut Roe again.jpg
 

SLOWnEASY

Contributor
Sr. Member
Joined
Sep 26, 2022
Messages
526
Loc.
San Diego, Ca.
I need to do this. Details?
@BroncoJimbo I loosely followed this link. https://www.broncohio.com/tech/gloveboxdoor.html
Instead of one long hinge pin I had a friend TIG weld some individual shafts into the hinges. (sorry no pictures)
Were I to do it again I would probably go with the one long shaft like in the link. Also since I'm running a replacement plastic glove box I had to do the prescribed trimming on both hinges not just the right hinge. Carefully mark the end of each hinge that you're going to cut. I got distracted and cut the wrong little hoop off and had to weld it back on.
 

1969miller

Contributor
Sr. Member
Joined
Jan 18, 2022
Messages
371
Loc.
Elk Grove
And, we're back... On today's episode of Bronco Life... The box is still doing box things... but in the meantime I took the Bronco out for a little spin after the completed water pump replacement. I'm elated to announce no leaks! Well, no leaks from the Water pump side of things. I was hoping I could fix this without removing the whole heater box but it appears it all has to come out. Should be awesome.
View attachment 955965
I just pulled mine out last night. Soo easy compared to new vehicles. 4 nuts for the heater box removed from engine bay along with both heater hoses, unhook air inlet duct inside and both defrost hoses under the dash, unplug heater resistor and heater, unscrew the 2 clamps holding the dash control cables and its out!
 

JeepGuy

Contributor
Bronco Guru
Joined
Aug 24, 2006
Messages
1,521
I just pulled mine out last night. Soo easy compared to new vehicles. 4 nuts for the heater box removed from engine bay along with both heater hoses, unhook air inlet duct inside and both defrost hoses under the dash, unplug heater resistor and heater, unscrew the 2 clamps holding the dash control cables and its out!
Yup. Took about 30 minutes of fumbling around. But I guarantee putting it back in will be at least a half day process. Luckily, the local Napa had the replacement in stock. It's already in the box. Now I'm just finding reasons to delay the reinstall process. :ROFLMAO:
 

hunter1

Contributor
Sr. Member
Joined
Feb 2, 2013
Messages
522
Loc.
Maryville, Tn
Yup. Took about 30 minutes of fumbling around. But I guarantee putting it back in will be at least a half day process. Luckily, the local Napa had the replacement in stock. It's already in the box. Now I'm just finding reasons to delay the reinstall process. :ROFLMAO:
Hardest part of the whole job is connecting the heater/defroster doors cables up. What a pain in the a**.
 

JeepGuy

Contributor
Bronco Guru
Joined
Aug 24, 2006
Messages
1,521
Hardest part of the whole job is connecting the heater/defroster doors cables up. What a pain in the a**.
U Aint Lion! 🤣 That was one of the best core exercises I've had in years. They seem just short enough that I could not get them hooked up prior to mounting the box back on the firewall. So after getting the box back in place, I pulled the Bronco close to my garage cabinets so I could lay on the driver's side floorboard with my feet pressed against the cabinets. I then managed to get my right hand up under the dash to hold the clip while my son used the longest Philips head screw driver we could find to get the screw seated securing the "Heat" cable. Need to finish up this morning with securing the defrost ducts and defrost cable which shouldn't be too bad. Then I get to move onto what is in that box.
Heater Box.jpg

Heater core.jpg


Luckily the foam around the old core was still very new. Still kicking myself for not replacing the core when I did everything else. Used a little contact glue to stick the foam back on the sided sealing up the cold air entrance into the box.
New heater core.jpg
 
Last edited:

JeepGuy

Contributor
Bronco Guru
Joined
Aug 24, 2006
Messages
1,521
Annnnnnnnnnnnnnnd, we're back... again... On today's episode of Bronco Life I reveal what was in that mystery box.

What's in the Box 2.jpg



That's right, you all guessed right... lol. Replacing the entire windshield wiper assembly and motor. I bought the full kit thinking it would not be a bad idea to have a spare windshield wiper switch laying around... might have been a good idea. Install is going pretty straight forward at this point, but as you might have guessed with my usual luck, it's not working. I'll post a thread in the tech so this doesn't go sideways on us.

But this is "What have I done to the bronco for the day."
 
Last edited:

JeepGuy

Contributor
Bronco Guru
Joined
Aug 24, 2006
Messages
1,521
Annnnnnnnnnndddddd we are back again. I gotta say, I'm not sure how I did it, but somehow I managed to weather the complete white out Blizzard we have going on down here in SoCal and found my newest arrival to the household... It was so cold outside I had to wear "slipa's" walking across the driveway to get them.

So, again, any guess at what are in these Boxes??? I cheated and opened the top one already 🤣
Whats in the boxes.jpg
 

JeepGuy

Contributor
Bronco Guru
Joined
Aug 24, 2006
Messages
1,521
Okay... All right... Enough with the harassing PM's. I know some of you have very limited patience and just can't wait to find out what in those boxes... 🤣

So here you go. First up was the small box which I kinda already let out in another thread...

Beginnings of a center Console set up and Switch panel.
Center Console Swich Panel Check.jpg


Second is the Wiper Motor Cover. Figured if I'm gonna replace the whole thing with nice new shinny parts I should at least try to keep them that way.

Wiper Motor Cover.jpg


Today's plans should not include any new boxes... yet... but more so trying to complete the two different projects I've started this week to prepare for next week's shenanigans.

Get out there and turn those wrench's or take for a drive people.
 

904Bronco

Contributor
Bronco Guru
Joined
Sep 28, 2004
Messages
6,720
Loc.
San Martin, CA
Made a replacement speaker cover. Unfortunately, with the AAW harness I can't fit a factory speaker in that location.
Still, it covers the wiring and such behind the dash...
 

Attachments

  • 20260115_124943.jpg
    20260115_124943.jpg
    303.9 KB · Views: 112
  • 20260115_173810.jpg
    20260115_173810.jpg
    258.7 KB · Views: 79
  • 20260116_154220.jpg
    20260116_154220.jpg
    249.1 KB · Views: 110
  • 20260116_174741.jpg
    20260116_174741.jpg
    122.2 KB · Views: 107

mdainsd

Contributor
Full Member
Joined
Mar 16, 2025
Messages
263
Loc.
San Diego
I got the drive train all worked out and installed into the frame today. Major mile stone! That a 427 roller mated to a 4R70W, and the stock transfer case. What started out to be trouble mating the engine, flexplate, torque converter and starter all came together perfectly.

IMG_3167.HEIC.jpeg
 

hunter1

Contributor
Sr. Member
Joined
Feb 2, 2013
Messages
522
Loc.
Maryville, Tn
Cut out a couple of interior panels yesterday and got them fitted. I also ordered some dark gray marine vinyl and foam backing for covering them. Also ordered some LED courtesy lights for under the dash and back corners of the panels. Also hooked up backup camera for the radio display. (Pic didn't come through)

View attachment 955944 View attachment 955945
Had a little time this afternoon and got one of the panels upholstered. Not fastened down yet.
IMG_0682.jpeg
 

JeepGuy

Contributor
Bronco Guru
Joined
Aug 24, 2006
Messages
1,521
Had a little time this afternoon and got one of the panels upholstered. Not fastened down yet. View attachment 956370
I'll probably end up doing something very similar. I'd like to incorporate some kind of side storage pockets in the rear, just not sure if I want to make them with a door, or open with netting.
 

JeepGuy

Contributor
Bronco Guru
Joined
Aug 24, 2006
Messages
1,521
So technically yesterday... really all weekend. Finished up the lower Center Console. That forced me to clean up all the wires left somewhat loose under the dash from the install and put a little thought into where things will be going in the future. As you all know, space is limited under the dash in these things, and this new box helped solve that major problem.

Center Console lower section complete.jpg
Center Console Wire Clean up..jpg
 
Top