• Welcome to ClassicBroncos! - You are currently viewing the forums as a GUEST. To take advantage of all the site features, please take a moment to register. It's fast, simple and absolutely free. So please join our community today!
    If you have problems registering or can't log into your account, please contact Admin.

73’ w/ 97’ Explorer 302 won’t start

wesward15

New Member
Joined
Jul 27, 2017
Messages
13
Alright, very novice mechanic here… I can’t get my Bronco to start. Originally thought battery, not it. I’ve changed the starter solenoid, ignition switch and checked all wiring ( that I can see). I can bridge the solenoid and it start every time. Key turned to on and get all lights, radio and fuel pump going but won’t start. What’s left? I’m thinking it’s got to be ignition wire broken somewhere? Thanks for any help!
 

EPB72

Contributor
Bronco Guru
Joined
Jul 13, 2019
Messages
1,216
Loc.
Pleasant Hill, CA
Have you tested ignition signal at starter relay ? A multimeter or test light would of helped ,, as old timer suggested if automatic wiggle/ cycle shifter , but if no power at relay and when jumped will crank ,, then will need to check that circuit between ignition switch and relay If auto would access NSS and test there or go straight to ignition switch and test there back probe for near battery voltage with key in crank position
 

Broncobowsher

Contributor
Total hack
Joined
Jun 4, 2002
Messages
37,112
Let me filter this out...
You have an engine that will run, but only if the solenoid is jumped. At this point I have to clarify a couple of things, let me know if I have this right. I presume you have the key on, jump the start post, it runs until you turn the key off.
There is another option that you are powering the "I" post on the solenoid and that is what you mean by jumping it. I don't think that is the case, but is possible from what has been described.

Back not starting with the key. Does the starter crank the engine over but just not start the engine? Or no starter spin at all? Those are 2 very different problems. It is not clear which one you are dealing with.

I am going to guess you know about the neutral start switch, no starter at all option.
You are probably really confused at the engine that will not start even though the starter is spinning away. Well that comes down to the ignition switch design. Switched ignition power isn't present in the start position. While that sounds absurd, as the switch was designed in the 60s the ignition was powered by the starter solenoid in the start position. Breaker point ignition and carburators just don't care. Some switches have ignition power in start, some don't, some are sometimes. I've had a couple of the sometimes ignition switches. I've know people who say it always works for them. Other (what I think you have) is the never have ignition power in start.
It isn't just a new switch, it is the basic design. The "I" post off the starter solenoid feeding back into the ignition position. Add a relay. Even a good sized diode off the start position back to ignition will do the trick.

Old fords that would just spin but not start, but would start running the moment the key was released back into the run position. That was a thing. That was a bad "I" post off the starter solenoid mixed with the ignition switch that doesn't have ignition power in start. That was common in a ton of old Ford cars back in the 70s
 

ksagis

Contributor
Aspiring Bronco Guru
Joined
Jun 15, 2020
Messages
819
Loc.
Austin
Not directly relevant to OPs post, but I thought the Bronco factory wiring was done such that the if the factory starter solenoid is getting power at the S terminal, it cross feeds a full 12 volts to ignition coil (via the I terminal on solenoid) when key is in start position? (I think I have S and I terminal right from memory)

1779720674220.png
 

SLOWnEASY

Contributor
Sr. Member
Joined
Sep 26, 2022
Messages
526
Loc.
San Diego, Ca.
To reiterate Broncobowsher's question
"Does the starter crank the engine over but just not start the engine? Or no starter spin at all? Those are 2 very different problems. It is not clear which one you are dealing with." Does the Bronco have a manual or automatic transmission?

If you don't have a 12v test light you might consider picking one up. But look for a test light that uses an incandescent bulb, not an LED. Here's one you might consider.
https://www.harborfreight.com/612v-circuit-tester-with-5-ft-lead-63603.html
With that light you can connect the ground clip to a good ground and then disconnect the Red/Blue wire on the S post of the starter relay and touch the test probe to the wire. Have a helper turn the key to the start position and see if the test light lights. If no light and it's an automatic transmission have the helper hold the key in the start position and cycle the shifter through all the gears while you watch the light for any flickers. If a manual make sure the clutch pedal is pressed all the way down.
 
OP
OP
wesward15

wesward15

New Member
Joined
Jul 27, 2017
Messages
13
Let me filter this out...
You have an engine that will run, but only if the solenoid is jumped. At this point I have to clarify a couple of things, let me know if I have this right. I presume you have the key on, jump the start post, it runs until you turn the key off.
There is another option that you are powering the "I" post on the solenoid and that is what you mean by jumping it. I don't think that is the case, but is possible from what has been described.

Back not starting with the key. Does the starter crank the engine over but just not start the engine? Or no starter spin at all? Those are 2 very different problems. It is not clear which one you are dealing with.

I am going to guess you know about the neutral start switch, no starter at all option.
You are probably really confused at the engine that will not start even though the starter is spinning away. Well that comes down to the ignition switch design. Switched ignition power isn't present in the start position. While that sounds absurd, as the switch was designed in the 60s the ignition was powered by the starter solenoid in the start position. Breaker point ignition and carburators just don't care. Some switches have ignition power in start, some don't, some are sometimes. I've had a couple of the sometimes ignition switches. I've know people who say it always works for them. Other (what I think you have) is the never have ignition power in start.
It isn't just a new switch, it is the basic design. The "I" post off the starter solenoid feeding back into the ignition position. Add a relay. Even a good sized diode off the start position back to ignition will do the trick.

Old fords that would just spin but not start, but would start running the moment the key was released back into the run position. That was a thing. That was a bad "I" post off the starter solenoid mixed with the ignition switch that doesn't have ignition power in start. That was common in a ton of old Ford cars back in the 70s
I’m jumping the source side of solenoid to the starter side. Key in on position, fires up and runs. I kill the engine by turning key to off position.
 

Broncobowsher

Contributor
Total hack
Joined
Jun 4, 2002
Messages
37,112
I’m jumping the source side of solenoid to the starter side. Key in on position, fires up and runs. I kill the engine by turning key to off position.
That's more info. But not enough.

Next, what happens when you turn the key to "start"?
Still not sure if we are dealing with a no spin of the starter issue
OR the starter cranks the engine as long as there is battery but the engine will never barks to life.

We need to know that before we can help anymore.
As stated before, 2 completely different issues. But you are not clear of exactly what is happening.
It start and runs, so most of it is correct.
 
OP
OP
wesward15

wesward15

New Member
Joined
Jul 27, 2017
Messages
13
Have you tested ignition signal at starter relay ? A multimeter or test light would of helped ,, as old timer suggested if automatic wiggle/ cycle shifter , but if no power at relay and when jumped will crank ,, then will need to check that circuit between ignition switch and relay If auto would access NSS and test there or go straight to ignition switch and test there back probe for near battery voltage with key in crank position

That's more info. But not enough.

Next, what happens when you turn the key to "start"?
Still not sure if we are dealing with a no spin of the starter issue
OR the starter cranks the engine as long as there is battery but the engine will never barks to life.

We need to know that before we can help anymore.
As stated before, 2 completely different issues. But you are not clear of exactly what is happening.
It start and runs, so most of it is correct.
Turning the key to start and it does nothing. Only way it cranks and runs is by bridging the solenoid. Is that what you’re looking for?
 

Broncobowsher

Contributor
Total hack
Joined
Jun 4, 2002
Messages
37,112
Yes, you are chasing a neutral start switch issue, not an ignition switch issue.
I presume the '73 started life as an automatic? I may be corrected on this, but I recall there was a 4-wire harness that started at the firewall by the steering column and went to the original C4. That carried the neutral start and the reverse light circuits so the switch on the side of the transmission could cycle them as per the shifter position. If it was a manual transmission there is the same 4-wire plug but 2 wires are jumped (neutral start) and the other 2 wires go the the reverse light switch on the column.

(note for others reading this later, this is only for '73 and newer. The wiring changed when the automatic was an option)

That 4-pin connector isn't tied into the Explorer harness correctly. Do you have working reverese lights? Key in run, shift to reverse (doesn't need to run) and see if there are reverse lights. This is my first place to look given the swap that just happened.

There are 2 more options. Bad range sensor on the transmission (they are typically pretty stout, doubt it) or the ignition switch has failed (typically they will give trouble before completely failing). So I am doubting those as well
Range sensor out of adjustment is another. With the foot on the brake, it could move, hold the key in start and row the shifter from park to 1st and back. That is a real easy test, 2 hands and one foot.

Then it goes to test light mode. This will grow into a 2-person job with one manning the key while someone else check the start wire through the neutral start switch to the starter.

Range selector test is quick and easy. But my bet is the transmission harness didn't get married to the Explorer harness correctly.
 

EPB72

Contributor
Bronco Guru
Joined
Jul 13, 2019
Messages
1,216
Loc.
Pleasant Hill, CA
I’m jumping the source side of solenoid to the starter side. Key in on position, fires up and runs. I kill the engine by turning key to off position.

Turning the key to start and it does nothing. Only way it cranks and runs is by bridging the solenoid. Is that what you’re looking for?
when jumping/bridge relay what are you jumping the two large post together thats what it sounds like in your previous post??? usually when jumping relay you supply power on the s terminal of the relay blue/red wire IF oe harness [aftermarket harness maybe diferent color [violet\ ..IF jumping the large lugs makes me think you might have a PMGR type starter with a piggybacked relay in starter motor?? which jumping large post at relay wouldnt take much current to crank starter if wired how most/supposed to wire PMGR ,, if original starter , then junping large post would require a rather large gauge jumper wire with jumper cable type clamps,,
regardless have you had someone turn key to crank position and confirmed if power is getting to S terminal ??

and a disagree with bowhser that we still dont know if it an ignition switch issue or not ,,it could be fine in the run position , but still fail when in crank position ,

looking at your avitar looks like been restored so more details of vehicle would help ,,
 

ksagis

Contributor
Aspiring Bronco Guru
Joined
Jun 15, 2020
Messages
819
Loc.
Austin
and given it worked for years, I’m assuming the basic wiring was done sufficiently before and something changed.

A simple test is pull the wire off S terminal and see if it has power when key is turned to start. That would rule out all switch, nss, etc very fast.

Somebody knows more about this then me, but does OP have a geared starter? Doesn’t that require some wiring mods?
 
OP
OP
wesward15

wesward15

New Member
Joined
Jul 27, 2017
Messages
13
and given it worked for years, I’m assuming the basic wiring was done sufficiently before and something changed.

A simple test is pull the wire off S terminal and see if it has power when key is turned to start. That would rule out all switch, nss, etc very fast.

Somebody knows more about this then me, but does OP have a geared starter? Doesn’t that require some wiring mods?
I’ll try all that’s been recommended. Bad thing is I’m right in the middle of a move of homes… I may reach out again next week once we’re moved and have some time to look it over. Thank you!
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
Not directly relevant to OPs post, but I thought the Bronco factory wiring was done such that the if the factory starter solenoid is getting power at the S terminal, it cross feeds a full 12 volts to ignition coil (via the I terminal on solenoid) when key is in start position?
Yes, exactly right.
The small Brown "I" wire is hot when the key is in the ON position, but it doesn't do anything to the starter relay because that stud is isolated until power gets to the "S" wire and that closes the internal contacts.
Because the Brown wire gets power from the key, that aspect of the ignition switch can be checked by probing the Brown wire with a volt-meter.
Or, in liu of a volt-meter, you can remove the Red w/blue "S" wire and swap the Brown "I" wire over to that S terminal. Make sure it's in Park or Neutral however, because as soon as you turn the key to ON, the starter will crank!
If it doesn't, then you have an ignition switch or wiring issue.
A simple test is pull the wire off S terminal and see if it has power when key is turned to start. That would rule out all switch, nss, etc very fast.
Also correct. Testing the starter relay is relatively easy most of the time.
First, for the OP, now that you've jumpered the two large posts and determined that the starter, battery and battery cables are all working, do the next test.
Remove the Red w/blue stripe wire from the "S" post and jumper from the hot battery side to the small post/terminal. IF the starter cranks, then you've proven that the starter relay is still good and you have an issue upstream.
If it does not work, then the relay is bad.
Somebody knows more about this then me, but does OP have a geared starter? Doesn’t that require some wiring mods?
Good question. It does require a little bit of a wiring change usually, but should not preclude the initial testing of the starter relay, the neutral-safety swtich (if present), the neutral-safety and backup light switch connector with bypass wire, and ignition switch.
But it's certainly next on the list!

Paul
 

DirtDonk

Contributor
Bronco Guru
Joined
Nov 3, 2003
Messages
51,650
I’ll try all that’s been recommended. Bad thing is I’m right in the middle of a move of homes… I may reach out again next week once we’re moved and have some time to look it over. Thank you!
I hate it when that happens!
First, moves are a hassle. Second, we hate waiting for a resolution! Haha...
But you gotta do what you gotta do. Definitely let us know what you find when you have time again.

Thanks

Paul
 
OP
OP
wesward15

wesward15

New Member
Joined
Jul 27, 2017
Messages
13
I hate it when that happens!
First, moves are a hassle. Second, we hate waiting for a resolution! Haha...
But you gotta do what you gotta do. Definitely let us know what you find when you have time again.

Thanks

Paul
Alright, I took a break from moving boxes.. the relay and starter are good. I wish it was that easy… I jumped out the relay, starter turned over. Tested the brown wire from switch and it has power. I changed the ignition switch Sunday. Thinking it’s a wiring issue?

Update: tested voltage on the back of ignition switch with key to start position. It had voltage on it. Probably have a break in the red/ blue stripe wire?
 
Last edited:

Oldtimer

Contributor
Jr. Member with Sr. moments
Joined
Feb 4, 2005
Messages
1,802
Loc.
Sunnyvale, CA
EDIT: Below comments are based on factory harness and C4 transmission. YMMV

Below is picture of neutral safety switch (NSS).

1779841923911.png


The mating connector is on the firewall, behind the driver side valve cover.
De-mate the plug, and check the wires coming thru firewall.
The BK/RD wires are the backup light circuit. One of them should be hot with key in ON or ACC position. Other BK/RD wire goes to backup lights.

The RD/BU wires are the NSS circuit. One of them should be hot with the key in START position. Other RD/BU wire continues on to the starter relay "S" terminal.
If one of the RD/BU wires is hot with key in START position, ignition switch is good.

SET PARKING BRAKE AND VERIFY TRANNY IS IN PARK.
Using a jumper wire* connect both RD/BU wires in firewall connector together (bypassing NSS) , and turn key to start position.
If starter relay engages, wire form firewall connector to "S" terminal on relay is good, and problem is NSS, or the wires connected to it.


1779842129948.png



*Easiest way to bypass NSS switch is to get a 2 pin connector harness from auto parts store, twist wires together, and plug into RD/BU half of firewall connector.

1779843296109.png
 
Last edited:
OP
OP
wesward15

wesward15

New Member
Joined
Jul 27, 2017
Messages
13
Below is picture of neutral safety switch (NSS).

View attachment 962475

The mating connector is on the firewall, behind the driver side valve cover.
De-mate the plug, and check the wires coming thru firewall.
The BK/RD wires are the backup light circuit. One of them should be hot with key in ON or ACC position. Other BK/RD wire goes to backup lights.

The RD/BU wires are the NSS circuit. One of them should be hot with the key in START position. Other RD/BU wire continues on to the starter relay "S" terminal.
If one of the RD/BU wires is hot with key in START position, ignition switch is good.

SET PARKING BRAKE AND VERIFY TRANNY IS IN PARK.
Using a jumper wire* connect both RD/BU wires in firewall connector together (bypassing NSS) , and turn key to start position.
If starter relay engages, wire form firewall connector to "S" terminal on relay is good, and problem is NSS, or the wires connected to it.


View attachment 962476


*Easiest way to bypass NSS switch is to get a 2 pin connector harness from auto parts store, twist wires together, and plug into RD/BU half of firewall connector.

View attachment 962477
Thank you! This was my next step and wasn’t sure on what to look for. Thank you for the knowledge, I’ll never forget it!
 

Broncobowsher

Contributor
Total hack
Joined
Jun 4, 2002
Messages
37,112
The above photo NSS is for a C4. The one on a 4R70W is in the same location, but completely different and a bunch more wires.
 
Top